L1
L2
L1
L2
L1
L2
L1
L2
L1
C x x x || A C T I V A T E
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form 169242
UNLOADING AND ASSEMBLY
C x x x || S E N S O R
I N P U T
M x x x || H D R
H E I G H T
C x x x || S E N S O R
I N P U T
M x x x || H E A D E R
A N G L E
C x x x || S E N S O R
I N P U T
M x x x || K N I F E
S P E E D
C x x x || S E N S O R
I N P U T
M x x x || R E E L
S P E E D
F U N C T I O N S ?
N O / Y E S
C x x x || A C T I V A T E
M x x x || H E A D E R
C x x x || A C T I V A T E
M x x x ||
R E E L
C x x x || A C T I V A T E
M x x x || H D R
T I L T
C x x x || A C T I V A T E
M x x x || K N I F E
D R I V E
C x x x || A C T I V A T E
M x x x || D R A P E R / A U G E R
C x x x || A C T I V A T E
M x x x || R E E L
C x x x || A C T I V A T E
M x x x ||
N O / Y E S
C x x x || T O
A C T I V A T E
M x x x || P R E S S
A N D
C x x x || P U R G E
C Y C L E
M x x x || P R E S S
A N D
C x x x || P U R G E
C Y C L E
M x x x ||
C x x x || P U R G E
C Y C L E
M x x x ||
N O
E X I T
C x x x || E X I T
F U N C T I O N
M x x x ||
N O / Y E S
C x x x || E X I T
D I A G N O S T I C S ?
M x x x ||
N O / Y E S
S E N S O R
S E N S O R
S E N S O R
S E N S O R
E X I T
F U N C T I O N S ?
D O W N / U P
For diagnostic purposes each header function can be
F U N C T I O N S ?
activated by using the "arrow" keys on the CDM. When
D O W N / U P
"SELECT" is pressed the program will go to the next
F U N C T I O N S ?
I N / O U T
F U N C T I O N S ?
O N
If the HEADER TILT cylinder or the REEL FORE / AFT
F U N C T I O N S ?
O N
menu then the ACTIVATE FUNCTIONS menu selection
F U N C T I O N S ?
F O R E / A F T
H Y D
P U R G E ?
ACTIVATE HYD PURGE - This is to allow the operator
to purge the air from a new or changed pump system.
P U R G E
H O L D
S T A R T E D
H O L D
Releasing pressure on the switch or a completed cycle
E N D E D
(timed out) will jump to the PURGE CYCLE ENDED
E N D E D
Y E S
M E N U ?
99
If a sensor has been disabled "SENSOR" will be
flashing in the area where the input reading would
have been.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
If "NO" then jump to:
D I A G N O S T I C S ?
function that can be activated.
valve is not installed under the TRACTOR SETUP
for these items should be suppressed.
Pressing and holding the right hand "arrow" button
activates a predetermined timed purge cycle.
menu selection.
If "NO" then jump to:
H E A D E R
D O W N / U P
If "NO" then jump to:
D I A G N O S T I C
M O D E ?
Revision F