MacDon M 2009 Series Assembly Instructions Manual page 96

L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1 C x x x || V I E W
M x x x ||
L2
L1
L2
L2
L1
L2
L2
L1
L2
L2
L1
L2
L2
L1
L2
L2
L1
L2
C x x x || E X I T
L1
L2 M x x x ||
L1 C x x x || C A B D I S P L A Y
||
L2 M x x x
C x x x || D I S P L A Y
L1
L2 M x x x ||
M x x x ||
L2
M x x x ||
L2
C x x x || D I S P L A Y
L1
M x x x ||
L2
L2 M x x x ||
Form 169242
UNLOADING AND ASSEMBLY
C x x x || D R A P E R
M x x x ||
E N A B L E D / L O C K E D
C x x x || A U G E R
S P E E D
M x x x ||
E N A B L E D / L O C K E D
C x x x || R E E L S P E E D
M x x x ||
E N A B L E D / L O C K E D
C x x x || R E E L F O R E / A F T
M x x x ||
E N A B L E D / L O C K E D
C x x x || H E A D E R
M x x x ||
E N A B L E D / L O C K E D
C x x x || E X I T
C O N T R O L
M x x x || N O / Y E S
C O N T R O L
N O / Y E S
C x x x || D R A P E R
M x x x || 5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || A U G E R S P E E D
M x x x ||
5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || R E E L
S P E E D
M x x x ||
5 7 5 . 1
M x x x || 6 4 8 . 6
C x x x || R E E L
F O R E / A F T
M x x x ||
5 7 5 . 1
M x x x || 6 4 8 . 6
C x x x || H E A D E R
M x x x || 5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || E X I T
V I E W
M x x x || N O / Y E S
T R A C T O R
N O / Y E S
S E T U P ?
N O / Y E S
L A N G U A G E ?
E N G L I S H
E S P A N O L
R U S S I A N
U N I T S ?
I M P E R I A L
M E T R I C
S P E E D
T I L T
L O C K S ?
L O C K S ?
E X I T
S P E E D
H R S E N A B L E D
H R S L O C K E D
H R S E N A B L E D
H R S L O C K E D
H R S E N A B L E D
H R S L O C K E D
H R S E N A B L E D
H R S L O C K E D
T I L T
H R S E N A B L E D
H R S L O C K E D
L O C K O U T S ?
S E T U P ?
T I L T
If "NO" then jump to:
C A L I B R A T E
Use the "arrow" keys to change the default language.
Pressing "SELECT" goes to the next L1 menu
The "arrow" keys are used to select between
IMPERIAL or METRIC. The default value will be
96
This menu allows the operator to selectably "lock out"
the control functions for the various header functions.
The default or selected "status" for each item will flash.
If the expansion module is not installed the
corresponding menu items should be suppressed.
The "arrow" keys are used to ENABLE or LOCK OUT
each function. Pressing "SELECT" will go to the next
L1 menu item.
Tilt to be suppressed if not "installed" in the tractor
setup menu.
If "NO" then jump to:
D R A P E R S P E E D
E N A B L E D / L O C K E D
If "NO" then jump to:
T R A C T O R S E T U P ?
When the control lock outs are viewed, the lower
display line (L2) will show the engine hours and either
ENABLED or LOCKED to indicate the present status
along with the engine hours at which time the function
was either ENABLED or LOCKED.
Using the "arrow" keys allows the operator to select the
various functions. Pressing "SELECT" will go to the
EXIT VIEW LOCKOUTS? menu selection.
If any of the HDR ANGLE / KNIFE SPEED or REEL
SPEED sensors are not "installed" (no expansion
module or A30 Auger header selected, they should be
suppressed.
If "NO" then jump to:
D R A P E R S P E E D
If "NO" then jump to:
C Y L I N S T A L L E D ?
S E N S O R S ?
selection.
displayed first.
(continued next page)
Revision F