MacDon M 2009 Series Assembly Instructions Manual page 98

||
L1 C x x x D I A G N O S T I C
||
L2 M x x x
C x x x || V I E W
L1
L2 M x x x ||
L1
L2
L1
L2
L1
L2
L1
L2
C x x x || E N T E R
L1
L2 M x x x ||
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1 C x x x || R E A D
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form 169242
UNLOADING AND ASSEMBLY
M O D E ?
N O / Y E S
E R R O R C O D E S ?
N O / Y E S
C x x x || V I E W T R A C T O R
M x x x ||
N O / Y E S
1 || 1 2 3 4 . 5
E 4 7 || S E N S O R
2 || 1 2 3 4 . 5
7 1 || L O W
E H Y D R A U L I C
C x x x || E X I T T R A C T O R
M x x x ||
N O / Y E S
S E N S O R
N O / Y E S
C x x x || H E A D E R
M x x x ||
E N A B L E / D I S A B L E
C x x x || H E A D E R
M x x x ||
E N A B L E / D I S A B L E
C x x x || K N I F E
S P E E D
M x x x || E N A B L E / D I S A B L E
C x x x || R E E L S P E E D
M x x x ||
E N A B L E / D I S A B L E
C x x x || E X I T
S E N S O R
M x x x ||
N O / Y E S
S E N S O R I N P U T S ?
N O / Y E S
C x x x || S E N S O R
M x x x || H D R
H E I G H T
C x x x || S E N S O R
M x x x || H E A D E R
C x x x || S E N S O R
M x x x || K N I F E
S P E E D
C x x x || S E N S O R
M x x x || R E E L
S P E E D
C x x x || S E N S O R
M x x x || W H E E L
S P E E D
C x x x || E X I T R E A D
M x x x ||
N O / Y E S
If "NO" then jump to:
T R A C T O R S E T U P ?
E N T E R
C O D E S ?
H R S 1 2 3
V O L T S L O W
H R S 1 2 3
O I L
C O D E S ?
S E T U P ?
R E A D
H T S E N S O R
T I L T S E N S O R
S E N S O R
S E N S O R
S E T U P ?
A C T I V A T E
I N P U T
3 . 5 9 V
I N P U T
A N G L E 1 . 8 4 V
I N P U T
1 2 3 H Z
I N P U T
1 2 3 H Z
I N P U T
1 2 3 H Z
S E N S O R S ?
98
If "NO" then jump to:
S E N S O R S E T U P ?
If "NO" then jump to:
E N T E R S E N S O R
The last 10 distinct error codes are stored along with
the code #, Exxx, engine hours and number of
occurrences. The "arrow" keys are used to cycle
between codes.
If "NO" then jump to:
V I E W T R A C T O R
If "NO" then jump to:
S E N S O R I N P U T S ?
The operator can select each sensor and selectively
enable or disable the sensor in the event of a sensor
malfunction.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
When "SELECT" is pressed the program goes to the
EXIT SENSOR SETUP? selection.
If "NO" then jump to:
K N I F E S P E E D
Or to the first sensor "installed"
If "NO" then jump to:
F U N C T I O N S ?
For diagnostic purposes each sensors input signal can
be read.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
When "SELECT" is pressed the program goes to the
EXIT READ SENSORS? menu selection.
Adds a selection to be able to read in the wheel speed
frequency.
If "NO" then jump to:
S E N S O R I N P U T
H D R H E I G H T
(continued next page)
S E T U P ?
C O D E S ?
S E N S O R
3 . 5 9 V
Revision F