MacDon M 2009 Series Assembly Instructions Manual page 97

IMPORTANT: ENGINE MUST BE RUNNING TO CALIBRATE SENSORS
C x x x || C D M
L1
M x x x ||
L2
C x x x || C D M
L1
M x x x ||
L2
C x x x || C D M
L1
L2 M x x x ||
C x x x || E X I T
L1
M x x x ||
L2
||
L1 C x x x C A L I B R A T E
||
L2 M x x x
C x x x || T O
L1
L2 M x x x ||
M x x x ||
L2
L2 M x x x ||
C x x x || H E I G H T
L1
M x x x || R A I S E
L2
L1 C x x x || C A L I B R A T I N G
M x x x || R A I S E
L2
L2 M x x x || R A I S E
C x x x || H E I G H T
L1
L2 M x x x || P R E S S
L1 M x x x || C A L I B R A T I N G
M x x x || L O W E R
L2
M x x x || H T
L2
C x x x || T O
L1
L2 M x x x ||
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
M x x x || H D R
L1
L2 M x x x || E X T E N D
C x x x || C A L I B R A T I N G
L1
L2 M x x x || E X T E N D
M x x x || E X T E N D
L2
M x x x || H D R
L1
M x x x || P R E S S
L2
C x x x || C A L I B R A T I N G
L1
L2 M x x x || R E T R A C T
M x x x || H D R
L2
C x x x || T O
L1
M x x x ||
L2
L2 M x x x ||
L1 C x x x || E X I T
M x x x ||
L2
Form 169242
UNLOADING AND ASSEMBLY
B U Z Z E R V O L U M E
▂ ▂ ▃ ▅ ▆ ▇
B A C K L I G H T I N G
▂ ▂ ▃ ▅ ▆ ▇
C O N T R A S T
▂ ▂ ▃ ▅ ▆ ▇
D I S P L A Y
N O / Y E S
S E N S O R S ?
N O / Y E S
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
S T O P & E X I T
S E N S O R
H D R T O
H E I G H T
H E A D E R
H E A D E R
S E N S O R
L O W E R H E A D E R
H E I G H T
H E A D E R
S E N S O R C O M P L E T E
C A L I B R A T E
H E A D E R H E I G H T
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
T I L T S E N S O R
T L T T O
T I L T
T I L T
T I L T
T I L T S E N S O R
R E T R A C T
T I L T
T I L T
T I L T C O M P L E T E
C A L I B R A T E
H E A D E R T I L T
S T O P & E X I T
C A L I B R A T I O N ?
N O / Y E S
The "arrow" keys are used to change the CDM buzzer
volume, CDM backlighting or the CDM contrast, with
the bar graph indicating the relative level for each
item. When "SELECT" is pressed the program goes to
the EXIT DISPLAY SETUP? menu selection.
S E T U P ?
D I S P L A Y
If "NO" then jump to:
D I A G N O S T I C
S E L E C T
The operator can select any of the two items requiring
calibration or to STOP & EXIT the menu.
When a function is activated, the display will indicate
the function being calibrated. HOLD will flash until the
C A L
system has completed reading in the signal with the
S T A R T
DONE will flash and prompt the operator to
H O L D
COMPLETE the sensor calibration by lowering the
D O N E
C A L
H O L D
The menu will display the last item selected when the
S E L E C T
calibration routine is completed.
S E L E C T
C A L
S T A R T
If the HEADER TILT option in the TRACTOR SETUP
H O L D
is set to NO then only HEIGHT should be available as
D O N E
a menu selection for calibration.
C A L
T I L T
H O L D
S E L E C T
T O C A L I B R A T E
97
If "NO" then jump to:
L A N G U A G E ?
M O D E ?
header fully raised.
header.
If "NO" then jump to:
S E L E C T
(continued next page)
Revision F