TANDBERG Alteia Instruction Manual page 184

Index
power-up default, 3-17, C-9
preset menu (#2) pages, C-9
setting up, 3-16
program clock reference (PCR), PID display, C-39
program map table (PMT) not available alarm, C-21
programme delivery and control (PDC), 1-9
PSU. See power supply
R
rack mounting standard, B-19
rear panel view, 1-22
Reed-Solomon decoding, 1-13, B-7
relays, auxiliary, 2-24
remote authorisation system (RAS), 1-8, 1-11, 1-22, 3-12
action of Authorized LED, 4-4
DSNG key, C-33
mode, C-33
RAS1, 3-13
RAS2, 3-13
remote control
address, C-35
choosing the interface, C-35
connector, 2-23, B-19
fault-finding, 6-6
front panel LED, 1-18
protocol (ST.TS.E9200), 1-18
summary, 1-8
rf input connector, 2-15, 2-16
routing
audio 1, C-28
audio 2, C-29
transport stream (SPI), C-34
RS-232
data connector, 2-22
remote control, 2-23, C-35
RS-422 data connector, 2-21
RS-485 remote control, 2-23, C-35
S
safety, B-21
ac supply operating voltage and fusing information, 2-6
disposal of moulded plugs, 6-9
handling and installation, 2-3
lightning protection, 2-5, 2-13, 2-14
moisture, 2-4
moving the equipment, 2-3
power lines, 2-5
wallsocket overloading, 2-6
sampling rates, audio, B-16
satellite receiver
8PSK L-band (#n) connector, 2-13
displayed BER value, C-13
forward error correction (FEC), C-13
input attenuator, 2-13, 2-14
input summary, 1-14
modulation mode, C-13
P8R input specification, B-9
PSR input specification, B-10
QPSK L-band (#n) input connector, 2-14
setting up the input, 3-6, G-1
signal acquisition range, C-13
system, 1-12
selecting
a service, 3-9, G-2
audio component, 3-11
data component, 3-12
preferred component language, G-3
preferred component language, 3-10
Index-6
selecting menu options, 3-5
self-tests
service ID display, C-39
service information (SI), 3-11
service menu (#3) pages, C-10
service provider, C-11
services
servicing
signal
single channel, audio, B-17
single packet burst mode, 1-12, 5-3
small rate buffer mode, C-36
small rbuff mode, C-37
SMPTE 302M-1998, B-6. See also linear audio. See also
software download. See over-air software download
software version
specification
status information
status menu (#1) pages, C-8
status screen, 1-7
stereo, audio, B-17
subtitles. See also DVB subtitles
Instruction Manual: Alteia and Alteia plus Professional Receivers and Decoders
displaying the result, C-36
clearing a preset, 3-18
list of teletext, C-11
selecting, 1-7, 3-9, G-2
service provider, C-11
setting the current service, C-11
setting up power-up default preset, 3-17
setting up power-up default service, C-9
setting up presets, 3-16
storing parameters, C-9
checks on completion, 6-4
damage indicating a requirement., 6-3
replacement parts \b, 6-3
connections, 2-9
degradation mode, 6-7
level, C-13
linear audio
covered by this manual, 1-4
introduction of new features, 1-6
VideoGuard boot code version, C-30
audio analogue output, B-6, B-16
audio digital output, B-6, B-17
audio monitor output, B-17
automatic gain control (AGC), B-18
auxiliary relays, B-19
data RS-232, B-18
data RS-422, B-18
decoder input, B-8
digital ENG receiver input, B-14
EN 300 421, 1-7
EN 300 744, 1-7
EN 301 210, 1-7
frame sync connector, B-14
ISO 13818, 1-7
low-noise block, B-12
P8R satellite input, B-9
power supply, B-20
PSR satellite input, B-10
remote control connector, B-19
television standards, B-5
terrstrial receiver input, B-12
transport stream output, B-15
video analogue composite output, B-15
video composite output, B-5
video digital output, B-16
video test output, B-16
asynchronous data, C-34
synchronous data, C-34
VideoGuard conditional access module, C-30
VideoGuard conditional access system, C-30
ST.TM.E9200.8