TANDBERG Alteia Instruction Manual page 129

------------------------------------------------------------------------------- MENU CONTROL --------------------------------------------------------------------------------
#8 AUDIO 1
(Section C.11)
A
1. Language / Dolby Dig
B
2. Output
3. Default Language
4. Routing
5. Sys Clipping Level
6. Level
7. AC3 Downmixing Mode
(option)
1. Language / Dolby Dig
2. Output
3. Default Language
4. Routing
5. Sys Clipping Level
6. Level
7. AC3 Downmixing Mode
(option)
Software Versions
2.1 and 2.2
(Section C.10.1)
1. Default Language
2. VITS Insertion
3. VPS Present
(Not supported)
4. WSS Present
(Not supported)
5. CC/VChip
6. AMOL 1
(Not supported)
7. AMOL 2
(Not supported)
Software Version 2.3
and later
(Section C.10.2)
1. Line/Input/Output
(Enhanced Models only)
2. Teletext
(Enhanced Models only)
3. VITS Insertion
4. VITC Insertion
(Enhanced Models only)
5. GCR Insertion
(Enhanced Models only)
6. CC/VChip
7. 525 Reinsertion
(Enhanced Models only)
8. 625 Reinsertion
(Enhanced Models only)
9. Default Subtitles
10. Subtitles
1. Resolution
2. Mode / Line Standard
3. PEL Aspect Ratio
4. Frame Rate
5. 625 Standard
6. 525 Standard
7. Fail Mode
8. Aspect Ratio
9. Level
10. EDH
(Enhanced Models only)
11. Embedded Audio
(Enhanced Models only)
12. Test Pattern
(Enhanced Models only)
13. Frame Sync
(Enhanced Models only)
14. Frame Sync 625
(Enhanced Models only)
15. Frame Sync 525
(Enhanced Models only)
Figure C.3: Pages under Menus #8 to #14
Instruction Manual: Alteia and Alteia plus Professional Receivers and Decoders
ST.TM.E9200.8
#9 AUDIO 2
#10 CA
(Section C.12)
(Section C.13)
No CA
1. Service Status
2. No CA Installed
VideoGuard CA, RAS
and BISS
(Section C.13)
1. Service Status
2. Status
3. CAS ID
4. Vguard Customer ID
5. CA Code Version
6. CA Boot Code Version
7. Model Number
8. Hardware Type
9. Manufacturer Number
10. Download Status
11. Med Priority Stream
12. Low Priority Stream
13. RAS Mode/DSNG Key
14. BISS Mode/Key
15. BISS-E Active ID
Scrolls through the
VBI line numbers to
view the contents of
the incoming and
outgoing data.
ü
ý Only available if Frame Sync
þ Option is purchased.
#11 DATA #12 TIMERS
(Section C.14) (Section C.15)
1. Async
2. Sync
3. TSO
4. ASI Optical
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
(ver 2.2 ®)
14.
15.
16.
17.
18.
19.
20.
(ver 2.3 ®)
21.
(ver 2.3 ®)
22.
(ver 2.6 ®)
(ver 2.6 ®)
Director Models
Local Lockout
Section
(
EDIT
SELECT
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
#13 SYSTEM
(Section C.16)
RIGHT
MENU
1. Time
2. Time Zone
#14 ENGINEERING
(Paragraph C.17)
Control mode
Remote Address
Remote Interface
LCD Contrast
Self Test Report
Model
Model Options
Demux Part Number
Demux Serial Number
Demux App Code Ver
Demux Core Code Ver
Demux Drv Code Ver
Demux Diag Code Ver
Output Part Number
U/P Part Number
U/P Code Version
I/P Part Version
I/P Code Version
Restore System
Reset Lockout PIN
Small RBUFF Mode
525 Video Start
Pages 12 and 13 are not
Only
included in software version
2.3 and later. As a result,
the remaining page
numbering will be lower by 2
C.16.3)
Control Mode
Set PIN
Remote Address
Remote Interface
LCD Contrast
Self Test Report
Model
Model Options
Demux Part Number
Demux Serial Number
Demux App Code Ver
Demux Core Code Ver
Demux Drv Code Ver
Demux Diag Code Ver
Output Part Number
U/P Part Number
U/P Code Version
I/P Part Version
I/P Code Version
Restore System
Reset Lockout PIN
Small RBUFF Mode
525 Video Start
Menus
1. Service ID
2. Transport Stream ID
3. Original Network ID
4. Network ID
5. Video PID
6. Audio 1 PID
7. Audio 2 PID
8. PCR PID
9. Async PID
10. Sync PID
11. Teletext PID
12. EMM PID
Demux App Code is the
software version shown on
the cover of this manual.
Demux App Code is the
software version shown on
the cover of this manual.
Pages 13 and 14 are not
included in software version
2.3 and later. As a result,
the remaining page
numbering will be lower by
2
Page C-5