TANDBERG Alteia Instruction Manual page 137

C.7.3 Satellite Receiver Input Menu Pages
This section applies to M2/PSR/932[C] and all M2/P8R/942 and
M2/PSR/942 models. Any differences between models are highlighted in
the Options column. Table 1.4 in Chapter 1, details the number of inputs
for the various models.
Table C.7: Satellite Receiver Input Menu (#4) Pages
Page Display
1 #4 INPUT
BER
n.n E - nn
2 #4 INPUT 1
LEVEL L- - - - OK- - - - H
155
3 #4 INPUT 1
selectable RF INPUT
NO 1
4 #4 INPUT 1
selectable KU BAND FREQUENCY
11410.0 MHz
5 #4 INPUT 1
selectable FEC SYM RATE
2/3 20.000000 MSYM/S
6 #4 INPUT 1
selectable POL
HORIZONTAL
7 #4 INPUT 1
selectable LNB TYPE
NORMAL
8 #4 INPUT 1
selectable LO FRQ 2
10000 MHz 10000.0 MHz
9 #4 INPUT 1
selectable LNB DC OUTPUT
ENABLED
10 #4 INPUT 1
editable LIMITS BER
1.8E-3
11 #4 INPUT 1
editable SEARCH RANGE
+/- 5000 kHz
Instruction Manual: Alteia and Alteia plus Professional Receivers and Decoders
ST.TM.E9200.8
Description
1/114 This page dynamically displays the Bit Error
Ratio (BER) at the receiver input.
32/114 This page dynamically displays the input signal
level. The three-digit number under LEVEL is the
T AGC level from the demodulator.
The display immediately to the right of LEVEL is
a scale representation of the AGC value.
33/114 The RF input is chosen using this menu. The
heading (INPUT n) in all menus in the group
changes to reflect the input number.
34/114 The parameter on this page is determined by the
frequency range entered in page 7. The
frequency bands appear in the options column.
OUT OF RANGE is displayed for an invalid
entry.
35/114 Set the Forward Error Correction (FEC) and
Symbol rate using this page.
Minimum increment is 100 Sym/s.
36/114
Use this page to set the antenna polarisation
MOD and modulation mode. When first displayed, the
QPSK page displays the current settings of the
modulation mode being used.
37/114
Set the LNB type in this page. Minimum LNB LO
LNB LO FREQ FREQ increment is 1 MHz.
10000 MHz
38/114 If the LNB type set in page 7 is not DUAL, the
SW OVR FREQ LO frequency and switchover point are set to
dashes.
Minimum LO FRQ2 increment is 100 kHz.
Minimum SW OVR FREQ increment is 100 kHz.
39/114 Allows the dc voltage to be applied to the LNB
via the currently selected output.
310/114 Set the BER and input signal input alarm
LEVEL thresholds. An alarm is generated if the BER is
050 above its alarm threshold or the signal level
below its alarm threshold.
311/11 Sets the upper and lower limits of the satellite
signal acquisition process.
Minimum increment is 1 kHz.
Options
INPUT NOT LOCKED
Display BER value
Keep the signal within the displayed band by
adjusting the input.
M2/PSR/942[A][B], M2/PSR/932C: 1, 2, 3, 4.
M2/PSR/932: M2/P8R/942: 1, 2.
C BAND (LNB LO: 5000 - 6000 MHz)
KU BAND (LNB LO: 9000 - 11 500 MHz)
L BAND (LNB LO º NONE)
FREQUENCY (LO frequency none of above)
OUT OF RANGE (User enters frequency in
the range 950 MHz to 2150 MHz)
FEC rates —
M2/PSR/9xx: ½, 2 / , ¾, 5 / , 6 / , 7 /
3 6 7 8
M2/P8R/9xx: / , / .
5 8
6 9
MODE —
M2/PSR/9xx: BPSK, QPSK.
M2/P8R/9xx: BPSK, QPSK, 8PSK
POL — HORIZONTAL, VERTICAL.
LNB TYPE —
NORMAL, DUAL, NONE.
LNB LO FREQ —
(LNB freq) MHz (LNB º NORMAL)
(LNB lower freq) MHz (LNB º DUAL)
- - - - - - (LNB type º NONE).
LO FREQ 2 —
(LNB upper freq) MHz (LNB º DUAL)
- - - - - - (LNB type º NORMAL/NONE).
SW OVR FREQ —
xxxxx MHz (switchover frequency)
- - - - - - (LNB type º NORMAL/NONE).
DISABLED (factory default)
ENABLED
BOOST
Page C-13
Menus
.