Related Manuals for TANDBERG CSR820
Summary of Contents for TANDBERG CSR820
-
Page 1: Installation And Operation
CSR820 Commercial Satellite Receiver Installation and Operation I DEOUARD CSR820 Commercial Satellite... - Page 2 Safety CAUTION Symbols RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE - NE AVIS: PAS OUVRIR The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the equipment.
-
Page 4: Table Of Contents
Table of Contents Introduction to CSR820....................... 1 Features................................1 Safety Notes......................... 1 Product Contents ........................ 2 Installing the CSR820 ......................2 Rear Panel Connections ..................... 3 Front Panel........................... 4 Menu Structure ........................5 Menu Screen Format ............................5 Getting Your IRD authorized....................6 Entering and changing Password .................. -
Page 5: Introduction To Csr820
19-inch selectable DC voltage to the LNB. equipment rack. • Alarm relay contacts to control external The CSR820 accepts L-Band input from an LNB. equipment. The CSR820 demodulates, decrypts, and • Reinsertion of closed captioning. Provides decompresses the digital signal and converts it DVB teletext and embedded subtitling. -
Page 6: Product Contents
Installation and Operation Guide Figure 1: Items shipped with CSR820 Installing the CSR820 Figure 2: Rack Mounting The CSR820 may be installed into a standard 1. Locate the two mounting brackets in the ANSI/EIA RS310-C 19” (48mm) rack (one rack installation kit. -
Page 7: Rear Panel Connections
ALARM type block The Alarm Relay states shown on the rear panel are Power Off and Fault state. When the CSR820 is powered on, the relay state will change NC to Open and NO to Closed. • The Alarm Relay cable shield must be connected to one of the Audio Ground pins (2 or 5). -
Page 8: Front Panel
Glows yellow when the CSR820 locks on to an incoming signal. AUTHORIZE Glows orange when the CSR820 decrypts the selected program. FAULT Glows red when the CSR820 detects a fault or failure. If FAULT LED remains lit, contact Tandberg Television Customer Service. -
Page 9: Menu Structure
• Login Symbol will be present if logged into the log out. menu system. 6. The CSR820 will automatically log out and • move up to the default screen after 3 minutes, The second line displays instructions or status information about the current parameter. -
Page 10: Getting Your Ird Authorized
Getting Your IRD authorized CSR820 can decrypt audio, video, and data Ensure the Smart Card is fully seated in the IRD. programs encrypted by NDS VideoGuard To get your IRD authorized, contact the program conditional access system. provider. In order to decrypt a program the IRD must be... -
Page 11: Quick Install And Setup Guide
CSR820 to complete its self test (about 30 format. seconds). Once the Self Test is successfully 3. Allow 30 seconds for the CSR820 to reboot. completed, the Default Screen will appear. Select a Service 4. If the FAULT LED remains lit, contact Tandberg Television Customer Service. -
Page 12: Menu Tree
Menu Tree Menu Tree CSR820 Menu System This diagram includes all of the menus and submenus in the CSR820 menu system. Arrows indicate the order of submenus within each main menu. Press OPTION or MENU as indicated. Items that you may enter are shown in bold type. -
Page 13: Menu Tree
Menu Tree To Receiver Setup MENU IRD Setup IRD Status Pre-Set Channels MENU Press OPTION Press OPTION Press OPTION MENU OPTION OPTION OPTION Video Mode: NTSC M < > PAL B, D, G, H, I, M, N Boot version: 1.9.9 Memory Not Set 1 Press ENTER to update NTSC-M... -
Page 14: Ird User Helpful Hints
IRD User Helpful Hints (NIT) in the data stream supplies further information if Frequency available. The NIT Satellite Delivery system descriptor frequency is the frequency on which the satellite Enter the IRD input frequency as accurate as is known. transmits the multiplex (Transponder Frequency). If the exact frequency is not known, the entered frequency should be accurate within the selected The formula to calculate the IRD input frequency is... -
Page 15: Video Mode
CSR820 to a pre-set channel from the service download. provider’s transport stream. NIM Version The CSR820 stores 12 pre-set channels. Channel 11 is reserved for Power Up. Channel 12 is the Emergency NIM Version displays the version number of the IRD’s Home channel. -
Page 16: Specifications
Specifications Power Input Input Voltage 100 – 240 VAC Single-phase Line Frequency 50 – 60 Hz Power Consumption 35 W max. RF Input Connector F-type connector, 75 ohm Input Waveform Shaped QPSK at variable symbol rates of 1 to 45 Msps RF Input Frequency Range 950 –... -
Page 17: Warranty
For breach of any written or implied warranty with If, during such twelve month period: respect to the product, in no event shall Tandberg Television be liable, in contract or in tort or under any Tandberg Television is notified promptly in writing upon... - Page 18 User Notes:...
- Page 20 Tandberg Television 25901 Commercentre Drive Lake Forest, CA 92630 USA (888) 637-0023 (United States only) (949) 725-2699...
Need help?
Do you have a question about the CSR820 and is the answer not in the manual?
Questions and answers