Mitsubishi Electric 800 Series Instruction Manual (Function page 506

Item
Shape of
terminal block
Contact input
Analog input
Control circuit
Relay output
terminal
Open collector
output
Pulse output
Analog output
Safety input/
output
Ethernet
Communication
RS-485
USB
Surrounding air temperature
Storage temperature
Plug-in option
Installation size
Panel through attachment
Machine speed display
Built-in potentiometer switching
Control mode selection
MRS input selection
Offline auto tuning
Applicable motor
Increment/range of acceleration/
deceleration time
 Installation precautions
• Removal procedure of the front cover is different. (Refer to the Instruction Manual (Connection).)
• Plug-in options of the FR-E700 series are not compatible.
 Wiring instructions
• When the FR-E700 standard control circuit terminal model is replaced, the terminal block type is changed from the screw
type to the spring clamp type. Use of blade terminals is recommended.
• To use the PU connector, note that wiring methods are different. (Refer to the Instruction Manual (Connection).)
FR-E800
Spring clamp type
Standard model: 7
Ethernet model: 2
Safety communication model: 0
2
1
Standard model: 2
Ethernet model and safety communication model: 0
1 (FM type only)
1 (AM type only)
S1, S2, PC, SO, SOC
2 ports (Ethernet model and safety communication
model)
CC-Link IE TSN, CC-Link IE Field Network Basic,
EtherNet/IP, PROFINET, MODBUS/TCP, and
BACnet/IP
1 port (standard model)
Mitsubishi inverter protocol, MODBUS RTU
Mini B connector: USB bus power available
(Maximum SCCR: 500 mA)
200/400 V class: -20°C to +60°C (Derate the rated
current when using the inverter in a temperature of
50°C or higher.)
575 V class: -10°C to +60°C (Derate the rated
current when using the inverter in a temperature of
50°C or higher.)
-40°C to +70°C
Dedicated plug-in options (not interchangeable)
Compatible (Use the installation interchange attachment for replacement of the FR-E720-175(3.7K)
and FR-E740-016(0.4K) to 040(1.5K).)
Not compatible
The rotation speed is displayed when Pr.53 = "1".
The machine speed is displayed when Pr.53 = "4".
Use Pr.37 and Pr.505 to set the reference for
machine speed.
Pr.146 unavailable (PA02 not supported)
V/F control when "40" is set in Pr.800.
Use Pr.17 to change the input specifications of the
MRS and X10 signals.
Set Pr.96 = "11" to enable offline auto tuning for V/
F control (frequency search for the automatic restart
after instantaneous power failure).
Offline auto tuning is enabled regardless of the
Pr.71 setting.
Set Pr.71 to a value whose last digit is 3 to change
the setting range of the motor constant.
Set "10" for the constant-torque motor.
The setting range cannot be changed from "0 to
3600 s" even when the increment is 0.01 s (Pr.21 =
"1").
19.1 For customers replacing the conventional model with this inverter
FR-E700
Standard control circuit terminal model: screw
type
Safety stop function model: Spring clamp type
Standard control circuit terminal model: 7
Safety stop function model: 6
2
1
2
1 (FR-E700)
1 (FR-E700-NA/EC/CHT)
S1, S2, PC (safety stop function model only)
1 port (FR-E700-NE only)
CC-Link IE Field Network Basic and MODBUS/
TCP
1 port
Mitsubishi inverter protocol, MODBUS RTU
Mini B connector: USB bus power unavailable
-10°C to +50°C
-20°C to +65°C
The machine speed is displayed when Pr.37 ≠
"0".
Pr.146 available
V/F control when "9999" is set in Pr.80 or Pr.81.
Use Pr.17 to change the input specification of
the MRS signal.
Set Pr.96 = "21" to enable offline auto tuning for
V/F control (frequency search for the automatic
restart after instantaneous power failure).
Set Pr.71 to a value whose last digit is 3 to
enable offline auto tuning.
Set Pr.71 to a value whose last digit is 4 to read
offline auto tuning data and change the setting.
Set "1" for the constant-torque motor.
The setting range can be changed to "0 to 360
s" when the increment is 0.01 s (Pr.21 = "1").
11
12
13
14
15
16
17
18
19
20
505
19. Appendix