Mitsubishi Electric 800 Series Instruction Manual (Function page 336

Setting
Signal
Positive Negative
name
logic logic
Inverter running and start
45 145 RUN3
command ON
During deceleration at
46 146 Y46 occurrence of power
failure
During PID control
47 147 PID
activated
48 148 Y48 PID deviation limit
Home position return
56 156 ZA
failure
During PM sensorless
57 157 IPM
vector control
60 160 FP Position detection level
During position command
61 161 PBSY
operation
62 162 CPO Rough match
Home position return
63 163 ZP
completed
64 164 Y64 During retry
70 170 SLEEP PID output interruption
80 180 SAFE Safety monitor output
81 181 SAFE2 Safety monitor output 2
82 182 Y82 BACnet binary output
Position control
84 184 RDY
preparation ready
90 190 Y90 Life alarm
Fault output 3 (Power-
91 191 Y91
OFF signal)
Energy saving average
92 192 Y92
value updated timing
93 193 Y93 Current average monitor
95 195 Y95 Maintenance timer
Function
Output while the inverter is running or while
the start command signal is ON.
Output when the power-failure deceleration
function is activated.
(The signal output is retained until the
function stops.)
Output during the PID control operation.
Output when the absolute deviation value
exceeds the limit value.
Output while the home position return error
warning occurs.
Output while the operation is performed
under PM sensorless vector control.
Output when the current position exceeds
the position detection judgment value (set in
Pr.1294 and Pr.1295).
Output while the position command
operation is performed.
Output when the remaining command
distance (before electronic gear) reaches
the Pr.510 setting value or less. (The
remaining distance can be calculated by
subtracting the position command (before
electronic gear) from the target position
(before electronic gear).)
Output when the home position return is
completed.
Output during retry operation.
Output while PID output suspension function
is activated.
Output while the safety stop function is
activated.
Output when no internal safety circuit failure
exists.
Enables output from the Binary Output
object for BACnet communication. This
signal can be assigned to Pr.192 only. (The
setting is available only for the FR-E800-
EPA and the FR-E800-SCEPA.)
Output when the servo-lock function is
working (the LX signal turns ON) and the
inverter is ready to operate.
Output when the life check function detects
the part approaching the end of its life.
Output when the Fault occurs due to an
inverter circuit fault or connection fault.
Switches between ON and OFF every time
the average energy saving is updated during
the energy saving monitoring. This signal
cannot be assigned to any of the relay
output terminal (Pr.192, Pr.320 to Pr.322).
Output in pulses for transmission of the
average current value and the maintenance
timer value. This signal cannot be assigned
to any of the relay output terminal (Pr.192,
Pr.320 to Pr.322).
Output when the value of Pr.503 reaches
the Pr.504 setting or higher.
Operation
parameter
—
Pr.261
Pr.127 to
Pr.134, Pr.575
to Pr.577
Pr.127 to
Pr.134,
Pr.553, Pr.554
—
Pr.71 to Pr.80,
Pr.998
Pr.1294 to
Pr.1297
—
Pr.510
—
Pr.65 to Pr.69
Pr.127 to
Pr.134, Pr.575
to Pr.577
—
Pr.549
—
Pr.198, Pr.255
to Pr.259,
Pr.506,
Pr.507, Pr.509
—
Pr.52, Pr.54,
Pr.158, Pr.891
to Pr.899
Pr.555 to
Pr.557
Pr.503, Pr.504
13. (M) Item and Output Signal for Monitoring
13.6 Output terminal function selection
Related
Refer to page
337
455
420
420
167
112
180
179
180
167
289
420
Instruction
Manual
(Functional
Safety)
Instruction
Manual
(Communication)
168
223
340
326
228
227
335
11
12
13
14
15
16
17
18
19
20