Mitsubishi Electric 800 Series Instruction Manual (Function page 371

Signal
Setting
name
76 X76
87 X87
88 LSP
89 LSN
92 X92
9999 —
*1 When Pr.59 Remote function selection ≠ "0", functions of the RL, RM, and RH signals are changed as shown in the table.
*2 When Pr.270 Stop-on-contact control selection = "1 or 11", functions of the RL and RT signals are changed as shown in the table.
*3 The OH signal is activated when the relay contact is open.
*4 For details, refer to the PLC Function Programming Manual.
NOTE
• The same function can be assigned to two or more terminals. In this case, the logic of terminal input is OR.
• The priorities of the speed commands are defined as follows: JOG > multi-speed setting (RH, RM, RL, REX) > PID (X14).
• When the Inverter run enable (X10) signal is not assigned, or when the PU operation external interlock (X12) signal is not
assigned while Pr.79 Operation mode selection = "7", the MRS signal performs the same function.
• The same terminals are used to assign the multi-speed (7-speed) setting and the remote setting. The multi-speed setting and
the remote setting cannot be assigned separately.
• When the terminal assignment is changed using Pr.178 to Pr.189 (Input terminal function selection), wiring may be
mistaken due to different terminal name and signal contents, or may affect other functions. Set parameters after confirming
the function of each terminal.
 Parameters available for each signal
• The following table shows the parameters to which the signals are assigned.
Setting Signal
value name
0 RL
1 RM
2 RH
3 RT
4 AU
5 JOG
7 OH
8 REX
10 X10
12 X12
13 X13
14 X14
15 BRI
16 X16
18 X18
23 LX
24 MRS
STP
25
(STOP)
26 MC
27 TL
30 JOG
37 X37
42 X42
43 X43
46 TRG
47 TRC
50 SQ
51 X51
370
14. (T) Multi-Function Input Terminal Parameters
14.6 Input terminal function selection
Function
Proximity dog
Sudden stop
Forward stroke end
Reverse stroke end
Emergency stop
No function
FR-E800
Pr.180 to
Pr.178 Pr.179
Pr.184
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
Pr.511, Pr.1282, Pr.1283,
Pr.1285, Pr.1286
Pr.464 to Pr.478
Pr.1292
Pr.1292
Pr.1103
—
FR-E800-E
Pr.185 to
Pr.178 Pr.179
Pr.189
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
— ○ ○
— ○ ○
○ ○ ○
— ○ ○
— ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
— ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
— ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
Refer to
Related parameter
page
167
170
170
170
232
—
FR-E800-
SCE
Pr.180 to Pr.180 to
Pr.189 Pr.189
○ ○
○ ○
○ ○
○ ○
○ ○
— —
— —
○ ○
— —
— —
○ ○
○ ○
○ ○
— —
○ ○
○ ○
○ ○
— —
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○