Mitsubishi Electric 800 Series Instruction Manual (Function page 509

19.3
Parameters (functions) and instruction codes
under different control methods
*1 Instruction codes are used to read and write parameters in accordance with communication (such as the Mitsubishi inverter protocol). (For details
of communication, refer to the Instruction Manual (Communication).)
*2 Function availability under each control method is shown as follows:
○: Available
×: Not available
Δ: Available with some restrictions
*3 For Parameter copy, Parameter clear, and All parameter clear, ○ indicates the function is available, and × indicates the function is not available.
*4 Communication parameters that are not cleared by parameter clear or all parameter clear (H5A5A or H55AA) via communication. (For details of
communication, refer to the Instruction Manual (Communication).)
*5 When a communication option is installed, parameter clear (lock release) during password lock (Pr.297 Password lock/unlock ≠ "9999") can be
performed only from the communication option.
Notation
Mark
Available for the standard model.
Available for the FM type inverter (standard model).
Available for the AM (50 Hz) type inverter (standard model).
Available for the AM (60 Hz) type inverter (standard model).
Available for the Ethernet model.
Available for the Protocol group A (Ethernet model / safety
communication model).
Available for the safety communication model.
Available for the 200 V class inverters.
Pr. Name
0 Torque boost
1 Maximum frequency
2 Minimum frequency
3 Base frequency
4 Multi-speed setting (high speed) 04
Multi-speed setting (middle
5
speed)
6 Multi-speed setting (low speed)
7 Acceleration time
8 Deceleration time
9 Electronic thermal O/L relay
DC injection brake operation
10
frequency
DC injection brake operation
11
time
DC injection brake operation
12
voltage
13 Starting frequency
14 Load pattern selection
15 Jog frequency
Jog acceleration/deceleration
16
time
MRS/X10 terminal input
17
selection
18 High speed maximum frequency 12
19 Base frequency voltage
508
19. Appendix
19.3 Parameters (functions) and instruction codes under different control methods
Description
Instruction
*1
code
00 80 0 ○
01 81 0 ○
02 82 0 ○
03 83 0 ○
84 0 ○
05 85 0 ○
06 86 0 ○
07 87 0 ○
08 88 0 ○
09 89 0 ○
0A 8A 0 ○
0B 8B 0 ○
0C 8C 0 ○
0D 8D 0 ○
0E 8E 0 ○
0F 8F 0 ○
10 90 0 ○
11 91 0 ○
92 0 ○
13 93 0 ○
Mark
Available for the 400 V class inverters.
Available for the three-phase power input model.
Available when the FR-A8AP is installed.
Available when the FR-A8AX is installed.
Available when the FR-A8AY is installed.
Available when the FR-A8AR is installed.
Available when the FR-A8NC is installed.
Available when the FR-A8ND is installed.
Available when the FR-A8NP is installed.
*2
Control method
Vector Vector Vector
Sensorless Sensorless Sensorless
× × × × ×
○ ○ ○ ○ ○
○ ○ ○ × ○
× × × × ×
○ ○ ○ Δ ○
○ ○ ○ Δ ○
○ ○ ○ Δ ○
○ ○ ○ Δ ○
○ ○ ○ Δ ○
○ ○ ○ ○ ○
○ ○ ○ × ○
○ ○ ○ × ○
○ × × × ×
○ ○ ○ × ○
× × × × ×
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
× × × × ×
Description
Parameter
PM PM PM
× × ○ ○
○ ○ ○ ○
○ ○ ○ ○
× × ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
× × ○ ○
○ ○ ○ ○
× × ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
× × ○ ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○