YOKOGAWA WT3001E User Manual page 128

6.18 NUMeric Group
The commands in this group deal with numeric data output.
There are no front panel keys that correspond to the commands in this group. The NUMERIC key on the front panel
can be used to specify the same settings. The DISPlay group commands can be used to query the settings.
:NUMeric?
Function Queries all settings related to the numeric data
output.
:NUMeric?
Syntax
:NUMERIC? -> :NUMERIC:FORMAT ASCII;
Example
NORMAL:NUMBER 15;ITEM1 U,1,TOTAL;
ITEM2 I,1,TOTAL;ITEM3 P,1,TOTAL;
ITEM4 S,1,TOTAL;ITEM5 Q,1,TOTAL;
ITEM6 LAMBDA,1,TOTAL;
ITEM7 PHI,1,TOTAL;ITEM8 FU,1;
ITEM9 FI,1;ITEM10 UPPEAK,1;
ITEM11 UMPEAK,1;ITEM12 IPPEAK,1;
ITEM13 IMPEAK,1;ITEM14 CFU,1;
ITEM15 CFI,1;:NUMERIC:HOLD 0
:NUMeric:CBCycle?
Function Queries all settings related to output of numeric
list data of Cycle by Cycle measurement.
:NUMeric:CBCycle?
Syntax
:NUMERIC:CBCYCLE? ->
Example
:NUMERIC:CBCYCLE:ITEM U,1;
START 1;END 100
:NUMeric:CBCycle:END
Function Sets the output end cycle of the numeric list data
output by :NUMeric:CBCycle:VALue? or queries
the current setting.
:NUMeric:CBCycle:END {<NRf>}
Syntax
:NUMeric:CBCycle:END?
<NRf> = 1 to 3000 (cycle number)
:NUMERIC:CBCYCLE:END 100
Example
:NUMERIC:CBCYCLE:END ->
:NUMERIC:CBCYCLE:END 100
6-84
:NUMeric:CBCycle:ITEM
Function Sets the numeric list data output items (function
and element) of Cycle by Cycle measurement or
queries the current setting.
:NUMeric:CBCycle:ITEM {<Function>,
Syntax
<Element>}
:NUMeric:CBCycle:ITEM?
<Function> = {FREQ|U|I|P|S|Q|LAMBda|
SPEed|TORQue|PM|PKU|PKI|PKSPeed|
PKTorque}
<Element> = {<NRf>|SIGMa|SIGMB} (<NRf>
= 1 to 4)
:NUMERIC:CBCYCLE:ITEM U,1
Example
:NUMERIC:CBCYCLE:ITEM? ->
:NUMERIC:CBCYCLE:ITEM U,1
Description • When <Function> = {FREQ|SPEed|
TORQue|PM|PKSPeed|PKTorque} ,
<Element> need not be specified. <Element>
is omitted from the response.
• When <Element> is omitted, Element 1 is set.
• {SPEed|TORQue|PM|PKSPeed|
PKTorque} is only available on models with
the motor evaluation function (/MTR option).
:NUMeric:CBCycle:STARt
Function Sets the output start cycle of the numeric list data
output by :NUMeric:CBCycle:VALue? or queries
the current setting.
:NUMeric:CBCycle:STARt {<NRf>}
Syntax
:NUMeric:CBCycle:STARt?
<NRf> = 1 to 3000 (cycle number)
:NUMERIC:CBCYCLE:START 1
Example
:NUMERIC:CBCYCLE:START ->
:NUMERIC:CBCYCLE:START 1
IM WT3001E-17EN