Amtech Axpert-Eazy Series Instruction Manual page 14

Table-3: 600V Series Axpert-Eazy drive (Terminal and applicable wire for Input and Output)
Rated
AMT-XXX-
Current
2
6
(A)
011 15
015 20
018
22
022 30
030
37
037 46
045
54
055 72
075 87
090
110
110 135
132
150
160 175
200
215
250 290
315
345
355
387
+
2p = Two parallel
(Note 3) Breaker for wiring
Install circuit breaker or fuse on the power supply side of the AC DRIVE. Refer to table and select
the Circuit Breaker or Fuses.
(Note 4) Power supply capacity
Make sure that the capacity of the transformer used as the AC DRIVE's power supply is 10 times
(or less) AC DRIVE capacity (for 4% impedance transformer). If the above value is exceeded,
install an ACL on the AC DRIVE's input side.
(Note 5) Noise filter
The AC DRIVE will generate high harmonic electromagnetic noise, so using the following noise
measures is recommended.
Insert a noise filter on the input side of the AC DRIVE. Contact Amtech to select the proper noise
filter.
Keep the wiring length between the noise filter and AC DRIVE to 500mm (19.7") or less.
Amtech
2.6
Wire
Lug size
size
+
max
(inch)
2
mm AWG
4 12 -
6 10 -
6 10 -
10 8 -
10 8 -
16 6 -
25 4 -
25 4 -
35 2 -
50 1/0 50 x M10
(0.43)
70 2/0 70 x M10
(0.43)
90 3/0 90 x M10
(0.43)
50 x 1/0 x 50 x M10
2p 2p x 2p (0.43)
70 x 2/0 x 70 x M10
2p 2p x 2p (0.43)
90 x 3/0 x 90 x M12
2p 2p x 2p (0.51)
150 x 250 150 x
2p kcmil M12 x 2p (0.51)
x 2p
185 x 300 185 x
2p kcmil M12 x 2p (0.51)
x 2p
Terminal
Lug Lug
width
ID width
mm
mm mm
(inch)
(inch)
I/P O/P
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
11.0 18.5 19 (0.75)
(0.73)
11.0 21.4 19 (0.75)
(0.84)
11.0 25.5 19 (0.75)
(1.0)
11.0 18.5 30 (1.18)
(0.73)
11.0 21.4 30 (1.18)
(0.84)
13.0 25.5 40 38
(1.0) (1.58) (1.50)
13.0 31.0 40 38
(1.22) (1.58) (1.50)
13.0 34.2 40 38
(1.35) (1.58) (1.50)
Hole Tightening
Terminal
diameter torque
screw
mm N*m
size
(inch) (lb - inch)
- - 1.92 (17)
- - 1.92 (17)
- - 1.92 (17)
- - 1.92 (17)
- - 1.92 (17)
- - 1.92 (17)
- - 4.3 (38)
- - 4.3 (38)
- - 4.3 (38)
10.5 M10 22.5 (199)
(0.41)
10.5 M10 22.5 (199)
(0.41)
10.5 M10 22.5 (199)
(0.41)
11.0 M10 22.5 (199)
(0.43)
11.0 M10 22.5 (199)
(0.43)
13.0 M12 31.2 (276)
(0.51)
13.0 M12 31.2 (276)
(0.51)
13.0 M12 31.2 (276)
(0.51)