Siemens SINUMERIK 840D sl Programming Manual page 415

A.1 Comparison of GUD parameters up to measuring cycles version 7.5 and GUD parameters as of measuring cycles vers
GUD up to Version 7.5
_CBIT[12]
_CBIT[13]
_CBIT[14]
_CBIT[15]
_CBIT[16]
_CHBIT[0]
_CHBIT[1]
_CHBIT[2]
_CHBIT[3]
_CHBIT[4]
_CHBIT[5]
_CHBIT[6]
_CHBIT[7]
_CHBIT[8]
_CHBIT[9]
_CHBIT[10]
_CHBIT[11]
_CHBIT[12]
_CHBIT[13]
_CHBIT[14]
_CHBIT[15]
_CHBIT[16]
_CHBIT[17]
_CHBIT[18]
_CHBIT[19]
_CHBIT[20]
_CHBIT[21]
_CHBIT[22]
_CHBIT[23]
_CHBIT[24]
_EVMVNUM[0]
_EVMVNUM[1]
_EV[n]
_MV[n
_SPEED[0]
_SPEED[1]
_SPEED[2]
_SPEED[3]
Measuring cycles
Programming Manual, 03/2009 Edition, 6FC5398-4BP10-2BA0
MD/SD as of Version 2.6
Can be used but is not a new MD/SD!
No function is assigned to this GUD.
MD51614 $MNS_MEA_PROBE_LENGTH_RELATE
SD54660 $SNS_MEA_PROBE_BALL_RAD_IN_TOA
MD51616 $MNS_MEA_CAL_MONITORING
MD51606 $MNS_MEA_INPUT_PIECE_PROBE[0]
MD51607 $MNS_MEA_INPUT_TOOL_PROBE[0]
SD55600 $SCS_MEA_COLLISION_MONITORING
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
No function is assigned to this GUD.
SD $SCS_MEA_RESULT_DISPLAY
Can be used but is not a new MD/SD!
No function is assigned to this GUD.
SD55602 $SCS_MEA_COUPL_SPIND_COORD
SD55604 $SCS_MEA_SPIND_MOVE_DIR
SD55606 $SCS_MEA_NUM_OF_MEASURE
SD55608 $SCS_MEA_RETRACTION_FEED
SD55610 $SCS_MEA_FEED_TYP
Can be used but is not a new MD/SD!
MD52605 $MCS_MEA_TURN_CYC_SPECIAL_MODE
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
Can be used but is not a new MD/SD!
No function is assigned to this GUD.
SD55622 $SCS_MEA_EMPIRIC_VALUE
SD55624 $SCS_MEA_AVERAGE_VALUE
SD55623 $SCS_MEA_EMPIRIC_VALUE[n]
SD55625 $SCS_MEA_AVERAGE_VALUE[n]
SD55630 $SCS_MEA_FEED_RAPID_IN_PERCENT
SD55631 $SCS_MEA_FEED_PLANE_VALUE
SD55632 $SCS_MEA_FEED_FEEDAX_VALUE
SD55633 $SCS_MEA_FEED_FAST_MEASURE
Appendix
415