Oki MB472dn User Manual page 583

Other Redial Tries
Settings
Redial Interval
Block Junk Setting
Fax List
Registered
List
Ring Response
Dialing Pause Duration
Rx Reduc. Rate
Reduc. Margin
ECM Mode
PreFix
Received Time Stamp
Print Check Message
Fax Service Bit
Setting
Country Code
A/R Full Print
Tone For Echo (For Transmission)
Tone For Echo (For Reception)
H/Modem Rate(For Tx)
H/Modem Rate(For Rx)
Attenuator
MF Attenuator
Pulse Make Ratio
Pulse Dial Type
MF(Tone) Duration
Calling Timer
PBX Line
Forwarding Forwarding Setting
Setting
Forwarding Number
TAD Mode
2 time(s)
1 minute(s)
OFF
Register/Edit (NULL)
Delete
1 Ring
2 second(s)
Auto
24 mm (0.9
inch) or
100 mm (3.9
inch)
ON
(NULL)
OFF
ON
OFF
International
or U.S.A
ON
Disable
Disable
33.6 Kbps
33.6 Kbps
10 dB, Range:
0 - 15 dB
8 dB, Range: 0
- 15 dB
40%, Range:
33, 39, 40%
N, Range: N,
10-N, N+1
100 mseconds,
Range: 75, 85,
100 mseconds
60 mseconds,
Range: 1 -
255 seconds
OFF
OFF
(NULL)
Type 3
582
image that is stored in the memory of this machine.
Sets the number of redial attempts.
Available range: 0 to 9 times
Sets the time between redial attempts.
Available range: 0 to 5 minutes
Sets Block Junk mode Fax.
Register/Edit addresses for Block Junk Fax.
Display condition: To set [Mode2] or [Mode3], [Admin Setup] >
[Other Settings] > [Block Junk Fax List] > [Setting].
Delete addresses for Block Junk Fax.
Display condition: To set [Mode2] or [Mode3], [Admin Setup] >
[Other Settings] > [Block Junk Fax List] > [Setting].
Sets the number of rings required before receiving an incoming
fax.
Sets the dial pause time.
Available range: 0 to 10 seconds
Sets the reception reduction rate.
Sets the threshold level of reception reduction.
Available range: 0 to 100 mm (0 to 3.9 inches)
Sets whether to use the error correction mode.
Sets the dialing prefix. You can enter up to 40 digits.
Sets whether to print the time stamp on received faxes.
Sets whether to report the error content if a transmission error
occurs.
If set to OFF, some menu items are not displayed on the screen.
Sets the country code.
Sets whether to print the list of the communication results
automatically after every 50 communications.
Displays only if Service Bit is ON.
Displays only if Service Bit is ON.
Sets the default modem reception transmission speed while the
machine is sending a fax.
Sets the default value of the modem transmission speed while
the machine is receiving a fax.
Enter Attenuator. Displays only if Service Bit is ON.
Enter MF(Tone) Attenuator. Displays only if Service Bit is ON.
Sets to make rate of DP (10 pps) during call. Displays only if
Service Bit is ON and Tone/Pulse setting is PULSE.
Sets the pulse type for dialing. Displays only if Service Bit is ON
and Tone/Pulse setting is PULSE.
Enter MF(Tone) Duration. Displays only if Service Bit is ON and
Tone/Pulse setting is TONE.
Displays only if Service Bit is ON.
When connecting to PBX (internal exchange), put it to [ON].
Sets whether to enable the fax forwarding mode.
Sets a fax number used for the fax forwarding mode.
Sets an operation type in Tel/Fax Ready mode.
[Type 3]: A fax signal is detected in 15 seconds from when the
answering machine answers. Normally, use this type.