Error Code; Warning Information Display - Panasonic AJ-PX5000G Operating Instructions Manual

Alarm
Warning content
Recording or playback operation
Action to take

Error code

If errors occur on the camera for any cause, the following error code is displayed on the time code display in the display window. Check the types of
warning, and deal with the error according to "Warnings description list" (page 220).
Code No.
First row
[E-30] [TURN POWER OFF]
[E-31] [TURN POWER OFF]
[E-33] [SYSTEM ERROR]
[E-34] [SYSTEM ERROR]
[E-35] [SYSTEM ERROR]
[E-36] [SYSTEM ERROR]
[E-37] [SYSTEM ERROR]
[E-39] [SYSTEM ERROR]
[E-63] No display
[SYSTEM ERROR]
[E-64]
or no display

Warning information display

Monitor display
First row
[AUTH NG CARD] (slot
None
number)
[BACKUP BATT EMPTY] None
[CARD ERROR] (slot
None
number)
[CLIP DISCONTINUED] None
[DIR NG CARD] (slot
None
number)
[FAN STOPPED] None
[PB INTERMITTENT]
None
(slot number)
[PROXY ERROR] None
[PROXY REC
None
WARNING]
[REC IMPOSSIBLE] (slot
None
number)
[REC WARNING] [FRAME SIGNAL]
Chapter 10 Maintenance and Inspection — Warning system
Does not sound.
There is an error in the fan and it stops. Otherwise [OPTION MENU] → [OPTION] → [FAN MODE] → [OFF] has been
set.
Operation will continue, but if the camera is operated with the fan stopped, the temperature rises and recording/playback
may not operate normally.
If the fan has stopped with error, stop using immediately and consult your dealer.
If the fan has stopped, temperature of the camera will rise. Therefore, do not use the camera for a long period of time.
Use the tripod, etc., and do not touch the camera directly.
Message display
Second row
[P2 CARD]
[SYSTEM MODE]
[CAMERA]
[LCD MICON]
[CODEC]
[P2 SYSTEM]
[P2CS]
[INITIALIZE]
No display
[FRAME SIGNAL]
or no display
Second row
CPS authentication of microP2 memory card has failed. The microP2
memory card whose CPS authentication failed cannot be recorded
or played back. Select [AUTHENTICATE] in the main menu →
[CLIP], and enter the password. For details, refer to "Manual CPS
authentication" (page 128).
Displays any reduced voltage detected on the backup battery in the
internal clock when the power is turned on.
Follow "Charging the built-in battery" (page 219) to charge the
battery.
Displayed when an data error caused by the P2 card occurs during
recording.
Displayed after recording stops until the next operation. Also
displayed for three seconds during playback when a P2 card error
causes playback to stop.
Replace the P2 card of the slot where the error occurred.
Displayed when clips cannot be linked with the subsequent recording
operations due to the inconsistency as linked clips during recording in
one-clip recording mode.
The directory position is not correct. Make a card backup immediately
and use again after formatting.
Displayed when the fan motor stops.
The camera operates even if the fan stops. Refrain from using
immediately.
Playback is interrupted on the SDHC/SDXC memory card. A card
whose playback performance cannot be assured is inserted. Use of
microP2 or P2 memory card is recommended.
Proxy error
For details, refer to "Error displays about proxy data recordings"
(page 47).
Proxy error
For details, refer to "Error displays about proxy data recordings"
(page 47).
An SDHC/SDXC memory card is inserted into the microP2 memory
card slot.
Recording to the SDHC/SDXC memory card is disabled. Record to
microP2 or P2 memory cards.
Displayed when a video or audio error occurs during recording. Turn
the power off and on before using it again.
When input signals are disrupted, recording continues while disrupted
images are recorded. Check the signal to be input to the camera.
Description
P2 card removal error
System mode error
Camera unit error
LCD microcomputer error
Codec control error
P2 system error
P2CS microcomputer error
Video initialization error
System control microcomputer error
Standard signal error
Description
– 222 –
Type of warning
3
Card removal error
2
Mismatched format
1
System error
1
System error
1
System error
1
System error
1
System error
1
System error
1
System error
1
System error
Camera operation
Continue
Continue
Stop
Continue
Continue
Continue
Continue
Continue
Continue
Continue
Continue