Network Settings; Wireless Lan Settings - Panasonic AJ-PX5000G Operating Instructions Manual

Network settings

To use wireless LAN or wired LAN, configuration of each setting is required. Configure the settings according to the function to use. When the main
menu → [I/F SETUP] → [USB/LAN] → [USB MODE] is set to [ON], the network function cannot be used.

Wireless LAN settings

This section describes the settings to connect the camera to mobile devices (iPad/iPhone), computers, or wireless access point via wireless LAN.
[DIRECT] mode
Use the following procedures when accessing to the network function of the camera directly from a smartphone, tablet, or computer.
1
Select [DIRECT] in the main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY] → [TYPE].
2
Set each item in the main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY] as necessary.
[MAC ADDRESS]: MAC address of wireless LAN (cannot be changed)
[SSID]: Network name of the camera (SSID) (Factory setting: [AJ-PX5000])
[CHANNEL]: Channel to be used (Factory setting: [AUTO])
[ENCRYPTION]: Encryption format to be used (Factory setting: [WPA2-AES])
[ENCRYPT KEY]: WPA2 encryption key (Factory setting: [01234567890123456789abcdef])
[DHCP]: Setting whether to use automatic acquisition via DHCP ([ENABLE]: Use automatic acquisition/[DISABLE]: Does not use automatic
acquisition) (Factory setting: [ENABLE]) (cannot be set)
[IP ADDRESS]: IP address of the camera (Factory setting: [192.168.0.1]).
[SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0])
[DEFAULT GATEWAY]: Default gateway (Factory setting: [192.168.0.254]) (cannot be set)
[PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (cannot be set)
[SECONDARY DNS]: Secondary DNS server setting (Factory setting: [0.0.0.0]) (cannot be set)
[DHCP SERVER]: Setting whether to use DHCP SERVER function ([ENABLE]: Use DHCP SERVER function/[DISABLE]: Does not use DHCP
SERVER function) (Factory setting: [ENABLE])
3
Select [WLAN] in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK SEL].
If the setting is changed, the camera will restart as necessary.
4
Select SSID from the list of the access points for mobile devices or computers and enter the password (encryption key).
Display the access point list screen in wireless setting and select [SSID] of the camera.
f Factory setting: [AJ-PX5000]
When the password confirmation screen appears, enter the password (encryption key).
f Factory setting: [01234567890123456789abcdef]
5
Check the network connection.
When the setting is completed, confirm that network connection of mobile devices (iPad/iPhone) and computers is made properly.
Application (P2 Browser) which requires network can be used when network connection is made properly. However, if connected with [DIRECT], the
FTP client function cannot be used.
[INFRA] mode
Use the following procedures when connected to the wireless access point.
1
Select [INFRA] in the main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY] → [TYPE].
2
Set each item in the main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY] as necessary.
Set [SSID], [ENCRYPTION], and [ENCRYPT KEY] according to the wireless access point to be connected to.
[MAC ADDRESS]: MAC address of wireless LAN (cannot be changed)
[SSID]: Network name of wireless access point (SSID) (Factory setting: [AJ-PX5000])
[CHANNEL]: Channel to be used (Factory setting: [AUTO]) (cannot be set)
[ENCRYPTION]: Encryption format to be used (Factory setting: [WPA2-AES])
[ENCRYPT KEY]: Encryption key of wireless access point (Factory setting: [01234567890123456789abcdef])
[DHCP]: Setting whether to use automatic acquisition via DHCP ([ENABLE]: Use automatic acquisition/[DISABLE]: Does not use automatic
acquisition) (Factory setting: [ENABLE])
[IP ADDRESS]: IP address of the camera (Factory setting: [192.168.0.1]).
[SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0])
[DEFAULT GATEWAY]: Default gateway (Factory setting: [192.168.0.254])
[PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS
server, it is is overwritten by the DNS server value which is acquired externally. When the value is [0.0.0.0], the server is not set.)
[SECONDARY DNS]: Secondary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the
DNS server, it is is overwritten by the DNS server value which is acquired externally. When the value is [0.0.0.0], the server is not set.)
[DHCP SERVER]: Setting whether to use the DHCP SERVER function ([ENABLE]: Use the DHCP SERVER function/[DISABLE]: Does not use the
DHCP SERVER function) (Factory setting: [ENABLE]) (cannot be set)
3
Select [WLAN] in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK SEL].
If the setting is changed, the camera will restart as necessary.
4
Check the network connection.
When the setting is completed, confirm that network connection between the camera and the wireless access point is made properly.
Chapter 9 Network Connection — Network settings
– 206 –