Panasonic AJ-PX5000G Operating Instructions Manual page 62

Chapter 4 Adjustments and Settings for Recording — Assigning functions to <USER> buttons
Item name
Assigns the function for recording test memos to frames when the button is pressed. For details on the text memo function, refer to "Text
[TEXT MEMO] memo recording function" (page 43). This function can be assigned only to the <TEXT MEMO> button. It cannot be assigned to other
<USER> buttons.
Toggles the brightness of the LCD monitor backlight. This is interlocked with the setting value in the main menu → [I/F SETUP] → [LCD
[LCD B.L]
MONITOR] → [BACKLIGHT].
Selects whether to display video in the viewfinder in color or black and white. This is interlocked with the setting value in the main menu →
[EVF CLR]
[VF] → [VF DISPLAY] → [VF COLOR].
Assigns the function to select the recording target slot between the P2 memory card slot and microP2 memory card slot. This setting is
[REC MEDIA]
linked to the setting value in the main menu → [REC/PB] → [REC/PB SETUP] → [REC MEDIA].
Only the following functions can be assigned to the <SHOT MARKER> and <TEXT MEMO> buttons.
f <SHOT MARKER> button
[INHIBIT]/[Y GET]/[ASSIST]/[REC SW]/[RET SW]/[PRE REC]/[SLOT SEL]/[USB MODE]/[LCD B.L]/[SHOT MARK]
f <TEXT MEMO> button
[INHIBIT]/[Y GET]/[ASSIST]/[REC SW]/[RET SW]/[PRE REC]/[SLOT SEL]/[USB MODE]/[LCD B.L]/[TEXT MEMO]
@ NOTE
t When the remote control unit AJ-RC10G (optional) or the extension control unit AG-EC4G (optional) is connected, and [I.OVR] or [C.TEMP] is
assigned to the <USER> buttons on the AJ-RC10G and AG-EC4G side, operation of the jog dial button on the camera is disabled.
t The following functions also turn off when the camera is turned off.
[I.OVR]/[S.BLK]/[B.GAMMA]/[Y GET]/[DRS]/[ASSIST]/[C.TEMP]/[ATW]/[ATW LOCK]/[D.ZOOM]/[S.GAIN]/[DS.GAIN]/[FBC]/[WFM]/[AUD CH1/3]/[AUD
CH2/4]/[USB MODE]
Note, however, that the [C.TEMP] color temperature is held after it is altered.
[USER SW GAIN] switching setting
In addition to [L/M/H] standard gain, the [S.GAIN] (super gain) mode for increasing analog gain to 30 dB or more and [DS.GAIN] (digital super gain) for
incrementally increasing gain using progressive drive can also be used on the camera.
For selection of this function, set the gains to be used in [S.GAIN] and [DS.GAIN] respectively in advance. Each item can be selected in the main menu
→ [CAMERA] → [USER SW GAIN]. With [S.GAIN], analog gain increase with [ON] set is enabled, and analog gain increase with [OFF] set does not
function. With [DS.GAIN], incremental analog gain increase with [ON] set is enabled, and analog gain increase with [OFF] set does not function.
When [S.GAIN] and [DS.GAIN] are assigned to one of the <USER MAIN>, <USER1> or <USER2> buttons, gain can be increased by a combination
with each of the <USER> buttons.
When increasing gain without an increase in noise
When increasing regular analog gain
(Noise is increased.)
When using as a super high-sensitivity mode
Description
Use the digital super gain function.
Use only the super gain function.
Note that the precision of auto iris, white balance and black balance is affected since noise
increases.
Use a combination of the super gain and digital super gain functions. Note, however, that
residual images will stand out more with moving subjects the greater the value for increasing
gain by digital super gain is set. Pay sufficient care when using this combination of functions.
For moving subjects, use [DS.GAIN] at [12dB] or below.
– 62 –