[System] - Panasonic AJ-PX5000G Operating Instructions Manual

Item
[LIST/DELETE] Views the list of CAC FILE stored in the camera internal memory and deletes files
of the numbers selected from the list of CAC FILE.
[No1]...[No32]

[SYSTEM]

[SYSTEM MODE]
Item
[LINE&FREQ] Sets the system number of lines and frequency, recording format, and audio
quantizing bit quantity. When the number of lines and frequency are selected,
only the items that can be selected for those frequencies are displayed. If the
frequency is changed, the device must be restarted. If a restart is required, a
confirmation dialog will be shown.
[1080-59.94P]
[1080-50P]
[1080-59.94i]
[1080-50i]
[720-59.94P]
[720-50P]
[480-59.94i]
[576-50i]
[REC FORMAT] Select the recording codec.
[AVC-I100]
[AVC-I50]
[AVC-G50]
[AVC-G25]
[AVC-G12]
[DVCPRO HD]
[DVCPRO50]
[DVCPRO]
[DV]
[AUDIO SMPL RES] If the recording format is AVC-Intra 100/AVC-Intra 50, selects number of the audio
recording quantizing bits.
[16BIT]
[24BIT]
[REC SIGNAL] Switches the video input signal.
[CAM]
[SDI]
[ASPECT] Selects the aspect ratio to record. (Only in SD)
[16:9]
[4:3]
[SCAN REVERSE] Sets whether to use function to correct video when using an anamorphic lens or
film lens.
[ON]
[OFF]
Chapter 7 Menu Operations — Menu list
Description of settings
Description of settings
Selects the number of lines 1080P and system frequency
59.94 Hz.
Selects the number of lines 1080P and system frequency
50 Hz.
Selects the number of lines 1080i and system frequency
59.94 Hz.
Selects the number of lines 1080i and system frequency 50 Hz.
Selects the number of lines 720P and system frequency
59.94 kHz.
Selects the number of lines 720P and system frequency 50 kHz.
Selects the number of lines 480i and system frequency
59.94 Hz.
Selects the number of lines 576i and system frequency 50 Hz.
Selects AVC-Intra 100.
Selects AVC-Intra 50.
Selects AVC-LongG 50.
Selects AVC-LongG 25.
Selects AVC-LongG 12.
Selects DVCPRO HD (100 Mbps).
Selects DVCPRO50 (50 Mbps).
Selects DVCPRO (25 Mbps).
Selects DV (25 Mbps).
16-bit is the audio recording bit quantity.
24-bit is the audio recording bit quantity.
Record signal from the camera
Record input from the <SDI IN> terminal
Recorded using the 16:9 aspect ratio.
Recorded using the 4:3 aspect ratio.
Corrects video. Inverts the top, bottom, left and right sides of a
video.
Does not correct video.
– 177 –
Remark
are factory settings.
Remark
f The setting values are saved together with the
settings of [REC FORMAT] and [AUDIO SMPL
RES] on each setting of [LINE&FREQ]. When
the settings of [LINE&FREQ] are restored to the
previous settings, these items are reset to the
previous settings at the time.
f When the camera is set to SD mode ([480-59.94i]
or [576-50i]), if [DVCPRO] or [DV] is changed to
[DVCPRO50] in [REC FORMAT], the following
setting values also change.
- When an item among [9s] to [15s] is set in the
main menu → [REC/PB] → [REC FUNCTION]
→ [PRE REC TIME], it is changed to [8s].
f [AVC-G50] and [AVC-G25] cannot be selected in
the following cases.
- When the main menu → [REC/PB] → [REC
FUNCTION] → [RECORDING] is set to
[INTERVAL] or [ONE SHOT].
f When this item is set to [DVCPRO] or [DV], if
SD mode ([480-59.94i] or [576-50i]) is changed
to HD mode (each mode of 1080 or 720) in
[LINE&FREQ], the following setting values also
change.
- When an item among [9s] to [15s] is set in the
main menu → [REC/PB] → [REC FUNCTION] →
[PRE REC TIME], it is changed to [8s].
f Types of available codecs vary depending on the
setting of [LINE&FREQ]. For details, refer to "Multi
formats" (page 50).
f When the recording format is AVC-LongG 50
or AVC-LongG 25, select [24BIT]. When the
recording format is DVCPRO HD, DVCPRO50,
DVCPRO, or DV, select [16BIT].
f Clips recorded at 24-bit should be played back
using a 24-bit compatible P2 device or P2 Viewer
Plus. The clip numbers of P2 devices that are
not 24-bit compatible are displayed in red and
cannot be used for playback. Audio does not play
back correctly on a P2 Viewer that is not 24-bit
compatible. Always use the latest P2 Viewer Plus
version.
f For 24-bit compatible P2 devices and the latest P2
Viewer Plus information, visit the P2 support page
on the following website.
http://pro-av.panasonic.net/
f Once the power is turned off, it is always set to
[CAM] the next time power is turned on.
are factory settings.