Table of Contents
Advertisement
f Press the playback related buttons.
f Press the <THUMBNAIL> button.
f Eject all the cards.
*5
The warning can be stopped by setting the [NEAR END CANCEL] item to [ON] and pushing the <DISP/MODE CHK> switch towards the <CHK> side.
Error code
Indicates the error code on the [HOME] screen of SmartUI when something has caused an error on the camera. Check the types of warning, and deal
with the error according to "Warnings description list" (page 157).
Code No.
E-27
E-30
E-38
E-3F
E-40
00000011
Card warning code
Code No.
E-70
E-71
Warning/error displays in the thumbnail operation and the USB host mode
r Thumbnail
Message
CANNOT ACCESS!
CANNOT CHANGE!
CANNOT COPY!
CANNOT DELETE!
CANNOT FORMAT!
CANNOT RE-CONNECT!
CANNOT REPAIR!
LACK OF CAPACITY!
MISSING CLIP!
NO CARD!
NO COPY TO SAME CARD!
NO FILE!
SAME CLIP IS SELECTED!
TOO MANY CLIPS!
UNKNOWN CONTENTS
FORMAT!
UNKNOWN DATA!
USER CLIP NAME MODIFIED!
WRITE PROTECTED!
Chapter 10 Maintenance and Inspection — Warning system
Description
Recording control error (viewfinder screen [P2 CONTROL ERROR])
P2 card removal error (viewfinder screen [TURN POWER OFF])
P2 streaming microcontroller error (viewfinder screen [P2 MICON
ERROR])
Camera unit error (viewfinder screen [CAM MICON ERROR])
Error in image sequence, generator lock input signal, or SDI input
signal (viewfinder screen [IRREGULAR FRM SIG], [PULL DOWN
ERROR])
Recording error to P2 cards, etc. (viewfinder screen [REC RAM
OVERFLOW], [CARD ERROR*], [OVER MAX# CLIPS], [ERROR])
Description
The directory structure on the P2 card is
not supported. ([DIR ENTRY NG CARD]
(slot number) is displayed on the viewfinder
screen.)
The maximum number of overwrites on the
P2 card has been exceeded. ([RUN DOWN
CARD] (slot number) is displayed on the
viewfinder screen.)
Description
Data cannot be accessed due to a content defect or some
other reason.
For a clip with the [
] mark, where a thumbnail cannot be
generated with AVC-Intra 100 or AVC-Intra 50, the thumbnail
cannot be modified in the text memo position.
Images cannot be copied.
Images cannot be deleted due to contents version mismatch.
A P2 card problem or some other reason prevents formatting.
Clips cannot be remerged because either clips that are not
recorded across multiple P2 cards are selected or other
reasons.
Clips cannot be restored because contents that cannot be
restored are selected or other reasons.
There is not enough recording capacity left on the card.
When all necessary P2 cards are not inserted, an attempt is
made to add a shot mark to the clips recorded across multiple
P2 cards.
No P2 or SD card is inserted.
A clip cannot be copied to the card storing the original clip.
The specified file does not exist.
Clips cannot be copied because the clips already copied and
the original clips are selected.
Too many clips are selected.
Contents version is mismatched.
The metadata character code is invalid.
Characters in the clip name had to be deleted when adding a
counter value.
The P2 or SD card is write-protected.
1. System error
2. Card removal error
1. System error
1. System error
5. Recording error, 6. Reference signal error
5. Recording error
Recording
Operation continues, but immediately back
up data on the card, and format the card
before using it again.
Operation continues, but recording
or playback may not be performed
properly. Replacement of the P2 card is
recommended.
Ensure the health of the media and the clips.
Set the [SYSTEM MODE] item on the setting menu [SYSTEM
SETUP] screen according to the clips.
Check the copy conditions.
Match the device and contents version.
Check the P2 card.
Check the selected content.
Check the selected content.
Insert a card with sufficient recording capacity.
Insert all P2 cards with the recorded clips and ensure that the
[
] incomplete clip indicator disappears, and then add the
shot mark.
Insert the relevant medium.
Copy the selected clip to a card that does not contain the
original clip.
Check the file.
Check the selected clips, and remove either the original clips
or copied clips, and then perform the copy operation.
Reduce the number of selected clips.
Match the device and content versions.
The metadata character code is UTF-8. Enter valid characters
using a viewer.
For the counter addition setting, the user clip name plus the
counter value can only contain up to 100 bytes. Characters in
the clip name are automatically deleted when the total number
of characters exceeds this limit.
Insert write-enabled media.
– 158 –
Type of warnings
Indication on SmartUI
The warning code is displayed on
the [HOME] screen of SmartUI.
Action to take
Advertisement
Table of Contents
