Low Setting - Panasonic AJ-PX5000G Operating Instructions Manual

Item
[R-Mg (PHASE)] Corrects the hue between red and magenta.
[−63]...[5]...[63]
[Mg (PHASE)] Corrects the magenta hue.
[−63]...[3]...[63]
[Mg-B (PHASE)] Corrects the hue between magenta and blue.
[−63]...[4]...[63]
Corrects the blue hue.
[B (PHASE)]
[−63]...[0]...[63]
[B-Cy (PHASE)] Corrects the hue between blue and cyan.
[−63]...[0]...[63]
[Cy (PHASE)] Corrects the cyan hue.
[−63]...[12]...[63]
[Cy-G (PHASE)] Corrects the hue between cyan and green.
[−63]...[15]...[63]
[G (PHASE)] Corrects the green hue.
[−63]...[10]...[63]
[G-Yl (PHASE)] Corrects the hue between green and yellow.
[−63]...[10]...[63]
[Yl (PHASE)] Corrects the yellow hue.
[−63]...[6]...[63]
[Yl-Yl-R (PHASE)] Corrects the hue between yellow and "colors between yellow and red".
[−63]...[22]...[63]
[Yl-R (PHASE)] Corrects the hue between yellow and red.
[−63]...[7]...[63]
[Yl-R-R (PHASE)] Corrects the hue between "colors between yellow and red" and red.
[−63]...[13]...[63]
f When saving or reading setup files from an SD memory card, you can save items with an [S] and items without an [S] separately. Items with an [S] in
front of the item name are the targets for [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT]. Items without an [S] are targets
for [PAINT(LEVEL)].

[LOW SETTING]

Item
[[S] MASTER GAIN] Selects the master gain.
[−6dB], [−3dB], [0dB], [3dB], [6dB], [9dB], [12dB], [15dB], [18dB], [21dB],
[24dB], [27dB], [30dB]
[H.DTL LEVEL] Sets the horizontal detail correction level.
[0]...[12]...[63]
[V.DTL LEVEL] Sets the vertical detail correction level.
[0]...[15]...[31]
[DTL CORING] Sets the detail noise removal level.
[0]...[1]...[60]
[H.DTL FREQ.] Selects the horizontal detail frequency.
[0]...[18]...[31]
[LEVEL DEPEND.] Sets [LEVEL DEPEND.].
Compresses the details of dark areas when Y detail is emphasized.
Details of bright areas are also compressed if the value is large.
[0], [1]...[5]
[MASTER GAMMA] Sets the master gamma in 0.01 steps.
[0.30]...[0.45]...[0.75]
[BLACK GAMMA] Sets the gamma curves of dark areas.
[−8]...[−1]
[OFF]
[1]...[8]
[B. GAMMA RANGE] Sets the maximum level of compression/expansion.
[1]
[2]
[3]
[[S] MATRIX TABLE] Selects the color collection table for the linear matrix.
[A], [B], [OFF]
[[S] COLOR Switches the 15-axis independent color correction on/off.
CORRECT] [ON], [OFF]
f When saving or reading setup files from an SD memory card, you can save items with an [S] and items without an [S] separately. Items with an [S] in
front of the item name are the targets for [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT]. Items without an [S] are targets
for [PAINT(LEVEL)].
Chapter 7 Menu Operations — Menu list
Description of settings
Description of settings
Compresses the dark areas.
Standard state
Expands the dark areas.
About 20%
About 30%
About 40%
– 144 –
Remark
are factory settings.
Remark
f [−6dB] in [[S] MASTER GAIN] cannot be selected
when [NORMAL] is set in main menu → [PAINT]
→ [[S] CAMERA SETTING] → [SHOOTING
MODE].
f A coloration phenomenon may occur in videos
of high-brightness areas if shooting was done
with the master gain set to [−6dB] or [−3dB].
After switching the <OUTPUT>/<AUTO KNEE>
selection switch to <CAM>/<OFF> and setting
[ON] in the main menu → [PAINT] → [KNEE/
LEVEL] → [[S] MANUAL KNEE], you can reduce
the coloration phenomenon by changing the
following menu items:
- Reduce the [KNEE MASTER SLOPE] value of
[KNEE/LEVEL] when [HD], [SD], [FILMLIKE1],
[FILMLIKE2], or [FILMLIKE3] is selected in the
main menu → [PAINT] → [GAMMA] → [GAMMA
MODE SEL].
- Reduce the [F-REC DYNAMIC LVL] value of
[GAMMA] when [FILM-REC] is selected in main
menu → [PAINT] → [GAMMA] → [GAMMA
MODE SEL].
- Reduce the [V-REC KNEE SLOPE] value of
[GAMMA] when [VIDEO-REC] is selected in the
main menu → [PAINT] → [GAMMA] → [GAMMA
MODE SEL].
are factory settings.