Panasonic AJ-PX5000G Operating Instructions Manual page 149

[[S] CAMERA SETTING]
Item
[SHOOTING MODE] Selects the shooting mode according to the shooting environment.
[NORMAL]
[HIGH SENS.]
[DETAIL] Switches the detail signal [ON]/[OFF].
[ON], [OFF]
[2D LPF] Sets a 2D low-pass filter to reduce cross colors.
[ON]
[OFF]
[GAMMA] Enables/disables gamma correction.
[ON], [OFF]
[TEST SAW] Enables/disables the test signal.
[ON], [OFF]
[FLARE] Enables/disables flare correction.
[ON], [OFF]
[H-F COMPE.] Enables/disables aperture correction.
[ON], [OFF]
f All [[S] CAMERA SETTING] items are targets of [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT].
[VF]
[VF DISPLAY]
Item
[VF/LCD CHAR] Selects whether to display a character on the image of the LCD monitor and
viewfinder.
[ON]
[VF-OFF]
[LCD-OFF]
[VF MODE] Selects a viewfinder image.
[MEM]
[CAM]
[VF COLOR] Selects whether to display viewfinder images in color or in black and white.
[ON]
[OFF]
[DISP CONDITION] Selects the status display method.
[NORMAL]
[HOLD]
[DISP MODE] Shows/hides camera warning/notification displayed in the center of the viewfinder.
For details, refer to "Display modes and setting changes/adjustment result
messages" (page 84).
[1], [2], [3]
[VF OUT] Selects the image signal displayed on the viewfinder screen.
[Y]
[NAM]
[R]
[G]
[B]
Chapter 7 Menu Operations — Menu list
Description of settings
Selects normal sensitivity. (Applies during shooting in normal
brightness.)
Selects high-sensitivity. (Appropriate when shooting in a dark
environment.)
[H.SENS.] is displayed on the viewfinder screen.
Reduces cross colors.
Does not reduce cross colors.
Description of settings
Displays a character on both the viewfinder and LCD monitor.
Does not superimpose on the viewfinder, and displays on the
LCD monitor.
Does not superimpose on the LCD monitor, and displays on the
viewfinder.
In playback mode, these are playback images.
Always camera images.
Displays in color.
Displays in black and white (playback images, thumbnail
screens and menu displays remain in color).
Status is always displayed.
Normally, status is not displayed. Push the <MARKER
SEL>/<MODE CHECK/MENU CANCEL> switch towards the
<MCK/MCL> side to display when the mode check screen is
displayed.
Luminosity signal
Outputs the [R], [G] or [B] signal with the largest level.
Rch signal
Gch signal
Bch signal
– 149 –
Remark
f If [NORMAL] is selected, [−6dB] cannot be
assigned to <LOW>/<MID>/<HIGH> on the
<GAIN> switch.
f If changed from [HIGH SENS.] to [NORMAL], the
following setting values also change.
- When [−6dB] is set in the main menu → [PAINT]
→ [LOW SETTING] → [[S] MASTER GAIN], it is
changed to [−3dB].
- When [−6dB] is set in the main menu → [PAINT]
→ [MID SETTING] → [[S] MASTER GAIN], it is
changed to [−3dB].
- When [−6dB] is set in the main menu → [PAINT]
→ [HIGH SETTING] → [[S] MASTER GAIN], it is
changed to [−3dB].
f This item is displayed when in SD mode
(480/59.94i and 576/50i).
are factory settings.
Remark
f This item is enabled when [CAM] is set in the main
menu → [SYSTEM] → [SYSTEM MODE] → [REC
SIGNAL]. When [SDI] is set, playback images are
output in the playback mode regardless of this
setting.
are factory settings.