Agilent Technologies InfiniiVision 2000 X-Series Programmer's Manual page 928

Index
threshold voltage (upper) for
measurement, 733
thresholds, 345, 728
thresholds used to measure period,
thresholds, how autoscale affects,
time base, 579, 580, 581, 582, 583,
time base commands introduction,
time base reset conditions, 137,
time base window, 585, 586, 587
time between points, 727
time buckets, 185, 186
time delay, 748
time delta, 727
time difference between data points,
time duration, 614
time holdoff for trigger, 594
time interval, 363, 365, 727
time interval between trigger and
occurrence, 731
time marker sets start time, 728
time measurements with X cursors,
time per division, 581
time record, 284
time reference, lister, 316
time specified, 374
time, calibration, 216
time, mask test run, 402
time, start marker, 729
time, stop marker, 730
time, system, 576
time/div, how autoscale affects,
TIMebase commands, 577
timebase vernier, 584
TIMebase:MODE, 56
time-ordered label list, 260
timeout, SPI clock, 497
timing measurement, 340
title channels, 225
title, mask test, 410
tolerance, automask, 386, 387
top of waveform value measured,
total frame count (CAN), 457
total waveforms in mask test, 391
trace memory, 179
track measurements, 360
trademarks, 2
transfer instrument state, 131, 574
tree traversal rules, 795
TRG (Trigger), 141, 143, 144
TRIG OUT BNC, 211
trigger armed event register, 167,
trigger burst, UART, 525
trigger channel source, 615, 625
TRIGger commands, 589
TRIGger commands, general, 591
trigger data, UART, 526
TRIGger EDGE commands, 601
trigger edge coupling, 602
trigger edge slope, 605
trigger event bit, 181
Trigger Event Register (TER), 766
TRIGger GLITch commands, 607
928
trigger holdoff,
trigger idle, UART,
TRIGger IIC commands,
355 trigger level auto set up,
153 trigger level constants,
748 trigger level voltage,
578 trigger level, high,
571 trigger level, low,
TRIGger LIN commands,
trigger occurred,
TRIGger PATTern commands,
trigger pattern qualifier,
trigger qualifier, UART,
657 trigger reset conditions, 137,
trigger SPI clock slope,
TRIGger SPI commands,
trigger status bit,
trigger sweep mode,
TRIGger TV commands,
trigger type, SPI,
325 trigger type, UART,
TRIGger UART commands,
trigger, CAN,
trigger, CAN pattern data length,
trigger, CAN pattern ID mode,
trigger, CAN sample point,
trigger, CAN signal baudrate,
trigger, CAN signal definition,
trigger, CAN source,
trigger, edge coupling,
153 trigger, edge level,
trigger, edge reject,
trigger, edge slope,
trigger, edge source,
trigger, force a,
trigger, glitch greater than,
trigger, glitch less than,
trigger, glitch level,
trigger, glitch polarity,
trigger, glitch qualifier,
375 trigger, glitch range,
trigger, glitch source,
trigger, high frequency reject filter,
trigger, holdoff,
trigger, IIC clock source,
trigger, IIC data source,
trigger, IIC pattern address,
trigger, IIC pattern data,
trigger, IIC pattern data 2,
trigger, IIC qualifier,
169 trigger, IIC signal baudrate,
trigger, IIC type,
trigger, LIN, 487
trigger, LIN pattern data,
trigger, LIN pattern data length,
trigger, LIN pattern format,
trigger, LIN sample point,
trigger, LIN source,
trigger, mode,
trigger, noise reject filter,
trigger, SPI clock slope,
trigger, SPI clock source,
Agilent InfiniiVision 2000 X-Series Oscilloscopes Programmer's Guide
594
527
469
595
227
603
596
597
479
143
616
620
528
571
496
493
181
589
621
507
529
509
463
466
468
459
460
461
462
602
603
604
605
606
592
609
610
611
612
613
614
615
593
594
471
472
473
474
475
476
483
477
489
491
492
482
484
598
599
496
499
trigger, SPI clock timeout, 497
trigger, SPI frame source, 500
trigger, SPI framing, 498
trigger, SPI pattern MISO width,
trigger, SPI pattern MOSI width,
trigger, sweep, 600
trigger, threshold, 749
trigger, TV line, 622
trigger, TV mode, 623, 750
trigger, TV polarity, 624
trigger, TV source, 625
trigger, TV standard, 626
trigger, UART base, 524
trigger, UART baudrate, 513
trigger, UART bit order, 514
trigger, UART parity, 520
trigger, UART polarity, 521
trigger, UART Rx source, 522
trigger, UART Tx source, 523
trigger, UART width, 530
truncation rules, 792
TST (Self Test), 145
tstart, 729
tstop, 730
TTL threshold voltage for digital channels, 249,
710
TTL trigger threshold voltage, 749
turn function on or off, 719
turn off channel, 158
turn off channel labels, 259
turn off digital pod, 158
turn off math function, 158
turn on channel labels, 259
turn on channel number display,
turning channel display on and off,
turning off/on function calculation,
turning vectors on or off, 714
TV mode, 623, 750
TV trigger commands, 621
TV trigger line number setting, 622
TV trigger mode, 625
TV trigger polarity, 624
TV trigger standard setting, 626
TV triggering, 590
tvmode, 750
Tx data, UART, 653
Tx frame count (UART), 518
Tx source, 523
type, 654
U
UART base, 524
UART baud rate, 513
UART bit order, 514
UART frame counters, reset, 516
UART parity, 520
UART polarity, 521
UART Rx source, 522
UART SEARch commands, 559
UART serial search, data, 560
UART serial search, data qualifier,
504
506
715
222
280
562