Agilent Technologies InfiniiVision 2000 X-Series Programmer's Manual page 922

Index
ESR (Standard Event Status Register), 128,
event status conditions occurred,
Event Status Enable Register (ESE), 126,
Event Status Register (ESR), 128, 181,
example code, :ACQuire:COMPlete,
example code, :ACQuire:SEGMented,
example code, :ACQuire:TYPE, 196
example code, :AUToscale, 154
example code, :CHANnel<n>:LABel,
example code, :CHANnel<n>:PROBe,
example code, :CHANnel<n>:RANGe,
example code, :DIGitize, 160
example code, :DISPlay:DATA, 258
example code, :DISPlay:LABel, 259
example code, :DISPlay:ORDer, 715
example code, :MEASure:PERiod,
example code, :MEASure:TEDGe,
example code, :MTESt, 379
example code, :POD<n>:THReshold,
example code, :RUN/:STOP, 176
example code, :SYSTem:SETup, 574
example code, :TIMebase:DELay,
example code, :TIMebase:MODE,
example code, :TIMebase:RANGe,
example code, :TIMebase:REFerence,
example code, :TRIGger:MODE,
example code, :TRIGger:SLOPe, 605
example code, :TRIGger:SOURce,
example code, :VIEW and :BLANk,
example code, :WAVeform, 650
example code, :WAVeform:DATA,
example code, :WAVeform:POINts,
example code, :WAVeform:PREamble,
example code, :WAVeform:SEGMented,
example code, *RST, 138
example programs, 5, 799
EXE (Execution Error) status bit, 126,
execution error detected in Standard Event
Status, 128
exponential notation, 117
external glitch trigger source, 615
external range, 274
external trigger, 271, 273, 606
EXTernal trigger commands, 271
EXTernal trigger level, 603
external trigger probe attenuation factor,
external trigger probe sensing, 717
EXTernal trigger source, 606
external trigger units, 275
F
failed waveforms in mask test, 388
failure, self test, 145
fall time measurement, 340, 350
Fast Fourier Transform (FFT) functions, 278,
281, 282, 284, 294, 718
FF values in waveform data, 637
FFT (Fast Fourier Transform) functions, 278,
281, 282, 284, 294, 718
FFT (Fast Fourier Transform) operation, 289,
649
922
769 FFT vertical units,
143 fifty ohm impedance, disable setting,
770 filename for hardcopy,
769 filename for recall, 419,
185 filename for save,
191 filter for frequency reject,
filter for high frequency reject,
filter for noise reject,
225 filter used to limit bandwidth, 220,
227 filters to Fast Fourier Transforms,
233 fine horizontal adjustment (vernier),
fine vertical adjustment (vernier),
finish pending device operations,
first point displayed,
FLATtop window for amplitude
362 measurements,
364 FM burst demo signal,
FM modulation type, waveform generator,
414 force trigger,
format, 639,
format for block data,
748 format for hardcopy,
579 format for image,
581 format for waveform data,
582 FormattedIO488 object,
598 formfeed for hardcopy, 296,
formulas for data conversion,
606 frame, 500
182 frame counters (CAN), error,
frame counters (CAN), overload,
637 frame counters (CAN), reset,
641 frame counters (CAN), total,
645 frame counters (UART), error,
191 frame counters (UART), reset,
frame counters (UART), Rx frames,
frame counters (UART), Tx frames,
128 framing, 498
frequency deviation, waveform generator FM
modulation,
frequency measurement, 51, 340,
frequency measurements with X cursors,
frequency resolution,
frequency span of display,
frequency versus dB,
front panel mode,
273 front panel Single key,
front panel Stop key,
front-panel lock,
FSK modulation type, waveform generator,
FSK rate, waveform generator modulation,
full-scale horizontal time, 581,
full-scale vertical axis defined,
function, 182, 280, 281, 282, 284, 288, 289,
290, 291, 292, 718,
FUNCtion commands,
function memory,
function turned on or off,
function, demo signal,
function, waveform generator,
functions, 649
Agilent InfiniiVision 2000 X-Series Oscilloscopes Programmer's Guide
283
573
721
666
428
604
593
599
272
284
584
236
132
659
284
239
682
592
644
131
720
431
440
53
300
632
454
455
456
457
515
516
517
518
674
351
325
284
282
278
600
178
180
568
682
677
586
290
719
277
179
719
238
667
G
g(t) source, first input channel, 286
g(t) source, math operation, 285
g(t) source, second input channel,
gateway IP, 42
general SBUS<n> commands, 449
general SEARch commands, 532
general trigger commands, 591
glitch demo signal, 238
glitch duration, 614
glitch qualifier, 613
glitch source, 615
GLITch trigger commands, 607
glitch trigger duration, 609
glitch trigger polarity, 612
glitch trigger source, 609
GPIB interface, 41, 42
graticule area for hardcopy print,
graticule colors, invert for hardcopy, 301,
graticule colors, invert for image,
grayscale palette for hardcopy, 309
grayscale palette for image, 433
grayscaling on hardcopy, 722
greater than qualifier, 613
greater than time, 609, 614
groups of digital channels, 411, 412, 414,
H
HANNing window for frequency
resolution, 284
hardcopy, 175, 296
HARDcopy commands, 295
hardcopy factors, 299, 430
hardcopy filename, 721
hardcopy format, 720
hardcopy formfeed, 300
hardcopy grayscale, 722
hardcopy invert graticule colors, 301,
hardcopy layout, 302
hardcopy palette, 309
hardcopy print, area, 297
hardcopy printer driver, 724
head type, probe, 228
header, 791
high resolution acquisition type, 631
high trigger level, 596
high-frequency reject filter, 593,
high-level voltage, waveform generator,
high-resolution acquisition type,
hold until operation complete, 132
holdoff time, 594
holes in waveform data, 637
hop frequency, waveform generator FSK
modulation, 676
horizontal adjustment, fine (vernier),
horizontal position, 585
horizontal scale, 583, 587
horizontal scaling, 644
horizontal time, 581, 586, 727
Host name softkey, 42
287
297
723
432
710
723
604
689
184
584