IBM NeXtScale nx360 M4 Installation And Service Manual page 255

SNMP Trap ID: 5
Automatically notify Support: Yes
User response:
1. Run the hard disk drive diagnostic test on drive n.
2. Reseat the following components: a. Hard disk
drive (wait 1 minute or more before reinstalling the
drive) b. Cable from the system board to the
backplane
3. Replace the following components one at a time, in
the order shown, restarting the server each time: a.
Hard disk drive b. Cable from the system board to
the backplane c. Hard disk drive backplane (n =
hard disk drive number)
806f010d-0408ffff The Drive
[StorageVolumeElementName] has been
disabled due to a detected fault. (1U
Storage HDD3)
Explanation: This message is for the use case when an
implementation has detected a Drive was Disabled due
to fault.
Severity: Error
Alert Category: Critical - Hard Disk drive
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0164
SNMP Trap ID: 5
Automatically notify Support: Yes
User response:
1. Run the hard disk drive diagnostic test on drive n.
2. Reseat the following components: a. Hard disk
drive (wait 1 minute or more before reinstalling the
drive) b. Cable from the system board to the
backplane
3. Replace the following components one at a time, in
the order shown, restarting the server each time: a.
Hard disk drive b. Cable from the system board to
the backplane c. Hard disk drive backplane (n =
hard disk drive number)
806f010d-0409ffff The Drive
[StorageVolumeElementName] has been
disabled due to a detected fault. (1U
Storage HDD4)
Explanation: This message is for the use case when an
implementation has detected a Drive was Disabled due
to fault.
Severity: Error
Alert Category: Critical - Hard Disk drive
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0164
806f010d-0408ffff • 806f010d-040bffff
SNMP Trap ID: 5
Automatically notify Support: Yes
User response:
1. Run the hard disk drive diagnostic test on drive n.
2. Reseat the following components: a. Hard disk
drive (wait 1 minute or more before reinstalling the
drive) b. Cable from the system board to the
backplane
3. Replace the following components one at a time, in
the order shown, restarting the server each time: a.
Hard disk drive b. Cable from the system board to
the backplane c. Hard disk drive backplane (n =
hard disk drive number)
806f010d-040affff
Explanation: This message is for the use case when an
implementation has detected a Drive was Disabled due
to fault.
Severity: Error
Alert Category: Critical - Hard Disk drive
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0164
SNMP Trap ID: 5
Automatically notify Support: Yes
User response:
1. Run the hard disk drive diagnostic test on drive n.
2. Reseat the following components: a. Hard disk
drive (wait 1 minute or more before reinstalling the
drive) b. Cable from the system board to the
backplane
3. Replace the following components one at a time, in
the order shown, restarting the server each time: a.
Hard disk drive b. Cable from the system board to
the backplane c. Hard disk drive backplane (n =
hard disk drive number)
806f010d-040bffff
Explanation: This message is for the use case when an
implementation has detected a Drive was Disabled due
to fault.
Severity: Error
Alert Category: Critical - Hard Disk drive
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0164
Appendix A. Integrated Management Module II (IMM2) error messages
The Drive
[StorageVolumeElementName] has been
disabled due to a detected fault. (1U
Storage HDD5)
The Drive
[StorageVolumeElementName] has been
disabled due to a detected fault. (1U
Storage HDD6)
237