Arctic Cat WILDCAT/X Service Manual page 126

Code Fault Description
P0485 Fan Relay Control Circuit Low/SG/Open
P0500 Vehicle Speed-Sensor
P0508 Idle Air Control System Circuit Low/SG
P0509 Idle Air Control System Circuit High/Open
P0520 Engine Oil Sensor/Switch
P0562 System Voltage Low
P0563 System Voltage High
P0601 ECM CAN Communication Shutdown
P0615 Starter Relay Circuit
P0616 Starter Relay Circuit Low
P0617 Starter Relay Circuit High
P0630 VIN Not Programmed or Incompatible
P0642 Sensor Power Circuit Low
P0643 Sensor Power Circuit High
P2300 Ignition Coil #1 Primary Circuit Low/SG/
Open
P2301 Ignition Coil #1 Primary Circuit High
P2303 Ignition Coil #2 Primary Circuit Low/Open Ignition coil #2 or interconnect harness open or shorted to chassis
P2304 Ignition Coil #2 Primary Circuit High
P2531 Ignition Switch Circuit Low
P2532 Ignition Switch Circuit High
U0155 LCD Gauge to EFI ECM CAN Communica-
tion Lost
U1000 Vehicle Not Registered or Invalid PIN
Entered
U1001 Vehicle Not Registered and Vehicle Limits
Enabled
FUEL OFF Tilt Sensor Activation Code
High: High voltage condition has been detected
Low: Low voltage condition has been detected
Intermittent: Intermittent circuit condition has been
detected
Open: Open circuit condition has been detected
124
Possible Cause
Fan fuse has blown, fan relay removed, or interconnect harness
shorted to chassis ground
Sensor circuit signal intermittent or missing
IAC interconnect harness shorted to chassis ground
IAC disconnected or the interconnect harness shorted to battery
power
Sensor or interconnect harness erratic or intermittent
Battery charge condition low or the regulator/rectifier output low
Battery cable connections are loose or regulator/rectifier output high Correct condition*
Intermittent CAN connections or unstable CAN conditions have
caused the ECM to temporarily shutdown CAN communication
Start switch/button, starter relay, gearswitch or interconnect harness
erratic or intermittent
Start switch/button, starter relay or interconnect harness intermittent
or shorted to chassis ground
Start switch/button, starter relay or interconnect harness intermittent
or shorted to battery power
Verify the LCD gauge and ECM part numbers are correct for the
vehicle model number and VIN
One or more of the sensors defective or shorted to chassis ground Correct condition*
One or more of the sensors defective or shorted to battery power
Ignition coil #1 or interconnect harness open or shorted to chassis
ground
Ignition coil #1 or interconnect harness shorted to battery power
ground
Ignition coil #2 or interconnect harness shorted to battery power
Battery charge condition low or the regulator/rectifier output low
Battery cable connections are loose or regulator/rectifier output high Correct condition*
Gauge CAN circuit or interconnect harness intermittent or has failed Correct condition*
An invalid registration PIN has been entered
An invalid registration PIN has been entered
Sensor activated
* After correcting condition, cycle key switch On-Off-On
**After correcting condition, cycle key switch On-Off-On, start
the engine, then cycle key switch Off-On.
Fault Recovery
Correct condition*
Correct condition*, start
and drive the vehicle*
Correct condition*
Correct condition*
Correct condition*
Correct condition*
Correct CAN communi-
cation issue*
Correct condition*
Correct condition*
Correct condition*
Correct gauge and ECM
VIN compatibility issue*
Correct condition*
Correct condition**
Correct condition**
Correct condition**
Correct condition**
Correct condition*
Enter the correct regis-
tration PIN*
Enter the correct regis-
tration PIN*
Restore the vehicle chas-
sis to an upright position*