Page 2 This page is intentionally left blank.
Page 3 This manual describes all the procedures that are required to start operation of the FUJITSU Storage ETERNUS DX60 S2 Disk storage system. This manual is intended for use of the FUJITSU Storage ETERNUS DX60 S2 Disk storage sys- tem in regions other than Japan.
Page 4: About This Manual
This chapter explains how to connect cables to the FUJITSU Storage ETERNUS DX60 S2 Disk storage system. ● Chapter 5 Setup This chapter explains how to set up the FUJITSU Storage ETERNUS DX60 S2 Disk storage system. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED...
Page 5 WARNING properly. This symbol indicates the possibility of minor or moderate personal injury, as well as damage to the FUJITSU Storage ETERNUS DX60 S2 CAUTION Disk storage system and/or to other users and their property, if the FUJITSU Storage ETERNUS DX60 S2 Disk storage system is not used properly.
Page 6: Additional Information
FUJITSU Storage ETERNUS DX60 S2 Disk storage system. Abbreviations Used in This Manual • "ETERNUS DX Disk storage system" or "ETERNUS DX60 S2" refers to the FUJITSU Storage ETERNUS DX60 S2 Disk storage system. • "Host Bus Adapter (HBA)" refers to the interface module that is normally used by the server to connect to ETERNUS DX Disk storage systems.
Page 7 Rear of the controller enclosure Device ID label The label with the model and serial # is located here. Front of the controller enclosure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 8 Power distribution units (for regions other than EMEA&I) • Power distribution unit (1U) anufacturer's label Information such as the model name and serial number is indicated. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 9 Warning Labels and Manufacturer's Labels • Power distribution unit (AC200-240V, 2U) anufacturer's label Information such as the model name and serial number is indicated. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 10: Table Of Contents
LAN Cable Connection (For iSCSI) ................... 66 4.2.3 MiniSAS Cable Connection (For SAS) ..................67 Drive Enclosure Connection ................69 Power Synchronized Unit Connection .............. 72 FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 11 Server Connection Setup ................126 System Status Check ..................126 Completion of the ETERNUS DX Disk Storage System Setup and Power Off ..................128 FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 12 Figure 2.27 Power distribution unit (2U, Max 8 enclosures connection)............44 Figure 5.1 PC terminal connection for initial setup ..................80 Figure 5.2 The [Assign Hot Spare] screen....................106 FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 13 Table 2.10 Status and meanings of each LED (expander)................42 Table 2.11 Status and meanings of each LED (power supply unit)............. 42 Table 3.1 Device installation order ......................45 FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 14: Chapter 1 Preparation
Table 1.1 Appropriate switch for each host interface type Host interface Switch to be prepared FC switch iSCSI LAN switch FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 15: Connection To Lan For Operation Management
ETERNUS DX Disk storage system of the previous Master CM’s are taken over by the new Master CM. Figure 1.1 LAN control (switching of the Master CM) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 16: Figure 1.2 Lan Control (When The Ip Address Of The Slave Cm Is Set)
Network devices and cables Network devices, such as LAN switches, must be prepared to connect an ETERNUS DX Disk storage system to the LAN. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 17: Figure 1.3 Lan Connection Example
LAN for operation management IP:x.x.x.a CM#0 CM#1 Controller enclosure ETERNUS DX Disk storage system : Enhanced Cat-5 twisted-pair type LAN cables Figure 1.3 LAN connection example FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 18: Figure 1.4 Lan Connection Example (When The Ip Address Of The Slave Cm Is Set)
When specifying the IP address of the Slave CM, specify an IP address that is in the same subnet but is different from the IP address of the Master CM. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 19: Figure 1.5 Connection Example Without A Dedicated Remote Support Port
Controller enclosure ETERNUS DX Disk storage system : Enhanced Cat-5 twisted-pair type LAN cables Figure 1.5 Connection example without a dedicated remote support port FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 20: Figure 1.6 Connection Example With A Dedicated Remote Support Port
Operation is performed with separate LANs for the MNT port and the RMT port. : Enhanced Cat-5 twisted-pair type LAN cables Figure 1.6 Connection example with a dedicated remote support port FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 21: Figure 1.7 Connection Example When The Ip Address Of The Slave Cm Is Set (And A Dedicated Remote Support Port Is Not Used)
: Enhanced Cat-5 twisted-pair type LAN cables Figure 1.7 Connection example when the IP address of the Slave CM is set (and a dedicated remote support port is not used) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 22: Figure 1.8 Connection Example When The Ip Address Of The Slave Cm Is Set (And A Dedicated Remote Support Port Is Used)
: Enhanced Cat-5 twisted-pair type LAN cables Figure 1.8 Connection example when the IP address of the Slave CM is set (and a dedicated remote support port is used) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 23: Table 1.2 Lan Port Availability
Storage Foundation Software ETERNUS SF. • ETERNUS SF Storage Cruiser • ETERNUS SF AdvancedCopy Manager • ETERNUS SF Express FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 24: Setup Preparation
IP address of RMT port For regions other than EMEA&I, the IP address for a RMT port of the ETERNUS DX Disk storage system FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 25: Figure 1.9 Attaching Network Settings Label
The following items are supported in firmware version V20L15 or later: • Internet Explorer 9.0, 10.0 (desktop version) • Firefox ESR 10.0.x, ESR 17.0.x FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 26 Subnet Mask: 255.255.255.0 Check the settings of the Web browser. Proxy server and Cache: Disable Java Script, style sheets, and cookies: Enable End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 27: Chapter 2 Components
Front view of a 3.5" type controller enclosure (with front cover) ● Without front cover 3.5-inch disk Operation panel Figure 2.3 Front view of a 3.5" type controller enclosure (without front cover) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 28: Rear View
Dual controller type Controller (CM#1) Controller (CM#0) Power Supply Unit Power Supply Unit (PSU#1) (PSU#0) Figure 2.5 Rear view of a controller enclosure (dual controller type) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 29: Components (Front)
READY LED FAULT LED MODE SELECT switch IDENTIFY LED IP RESET switch CACHE LED Power switch Figure 2.7 Operation panel (3.5" type controller enclosure) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 30: Table 2.1 Status And Meanings Of Each Led (Operation Panel (Controller Enclosure))
There is data in the ETERNUS DX Disk storage system cache memory. (green) Data in the cache memory is saved to a non-volatile memory. (blinks green) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 31: Figure 2.8 2.5" Type Disk
LED name LED status Disk status DISK READY The disk is operating normally. (green) (blinks green) DISK FAULT The disk is in error status. (orange) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 32: Figure 2.10 3.5" Type Disk
LED name LED status Disk status DISK READY/ The disk is operating normally. FAULT (green) (blinks green) The disk is in error status. (orange) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 33: Components (Rear)
This port is used to connect a controller enclosure to a drive enclosure with a miniSAS cable. • LEDs The states of LEDs are listed below. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 34: Figure 2.13 Controller (Iscsi Model)
(0 (Left), 1 (Right)) UNIT READY/FAULT LED MASTER LED PWC port FAULT LED LINK LED ACT LED LINK LED DI (OUT) port Figure 2.13 Controller (iSCSI model) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 35: Table 2.5 Status And Meanings Of Each Led (Iscsi Model Controller)
The controller is performing the initial setup after (orange) the power is turned on. • The iSCSI port (host interface port) is in error status. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 36: Figure 2.14 Controller (Sas Model)
(blinks blue) (off) DI (OUT) LINKUP The link between the DI (OUT) port and the destination has been established. (green) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 37: Figure 2.15 Power Supply Unit
Figure 2.15 Power supply unit ● Part explanation • Inlet This inlet is used to connect a power cord. • LEDs The states of LEDs are listed below. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 38: Drive Enclosure
Figure 2.16 Front view of a drive enclosure (with front cover) ● Without front cover 3.5-inch disk Operation panel Figure 2.17 Front view of a drive enclosure (without front cover) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 39: Rear View
AUTO POWER switch FAULT LED IDENTIFY LED MODE SELECT switch This switch is not used. Figure 2.20 LEDs on the front side of the drive enclosure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 40: Figure 2.21 3.5" Disk
Slot#7 Slot#0 Slot#1 Slot#2 Slot#3 Figure 2.22 Disk slot numbers (drive enclosure) ● Part explanation • LEDs The states of LEDs are listed below. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 41: Components (Rear)
Figure 2.23 Expander ● Part explanation • DI (IN) port These ports are connectors for miniSAS cables. • LEDs The states of LEDs are listed below. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 42: Figure 2.24 Power Supply Units
ETERNUS DX Disk storage system (DC power) is not (blinks green) turned on. The power supply unit or the fan in the power supply (orange) unit is in error status. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 43: Power Distribution Units (For Regions Other Than Emea&I)
• Outlet (OUTPUT) This is a socket (IEC60320-C13) for outgoing power supply. This socket is used to connect a power cord (AC output cable). FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 44: Power Distribution Units (2U)
• Outlet (OUTPUT) This is a socket (IEC60320-C13) for outgoing power supply. This socket is used to connect a power cord (AC output cable). FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 45: Chapter 3 Rack Installation
UPS units in a single rack, mount the devices in the following order (from bottom to top). Table 3.1 Device installation order Order Device Power distribution unit, Power synchronized unit Controller enclosure Drive enclosure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 46: Installing Power Distribution Unit (For Regions Other Than Emea&I)
Remove the two M3 screws from the front of the power distribution unit to free the brackets. Bracket A Power distribution unit M3 screw Bracket B M3 screw FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 47 Install the power distribution unit in the rack. Fasten the power distribution unit to the bracket with the two M3 screws removed in Step M3 screw (Rear rack pillars) M3 screw FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 48: Installing Power Distribution Unit (2U)
4th position 4th position Power distribution unit Power distribution unit 3rd position 3rd position 1st position 1st position Base line of power distribution unit FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 49 The blank panel should be attached at the same height as the power distribution unit. Blank panel Power distribution unit (Front rack pillars) (Rear rack pillars) End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 50: Installing Controller Enclosure
The M5 centering screws should be inserted in the 1st and 6th holes above the base line of the controller enclosure. 2U Bracket M5 Centering screws (10mm) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 51 (M5 cage nut) (M5 cage nut) 1st position 1st position (M5 pan head screw) (M5 pan head screw) Base line of controller enclosure Rack rails (Brackets) FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 52 M5 screws M5 screws Bracket L (Rear rack pillars) Screw holders Screw holders M5 screws (Front rack pillars) M5 screws Bracket R Screw holders FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 53 ■ 2.5" type controller enclosure Use the thumb screw to fasten the front right of the controller enclosure to the rack. (Rear rack pillars) Thumb screw FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 54 Flange cover Use the thumb screw of the flange cover to fasten the front left of the controller enclosure to the rack. Thumb screw FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 55 Be careful so that the part of the front cover to be fit in the slot IMPORTANT does not touch the power switch ( Slot FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 56: Installing Drive Enclosure
A drive enclosure must be installed above a controller enclosure. IMPORTANT FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 57 Insert the pins of the left slide rail in the 1st and 3rd holes from the bottom of the 2U Bracket. Secure the left slide rail to the front pillar using the M5 centering screw and M5 pan head screws. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 58 [Left] (Front rack pillars) Bracket R (for right side) "R" is stamped on the inner side of the right rack rail. [Right] FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 59 Failure to do so may cause injury. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 60 Be careful so that the part of the front cover to be fit in the slot IMPORTANT does not touch the power switch ( Slot FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 61 When attaching the right side of the front cover, support its left side with your left hand, to prevent it from coming loose and falling. End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 62: Chapter 4 Connecting Cables
When disconnecting LAN cables, depress the tab, then pull out the connector. This section describes dual controller type as an example. Note that there is only controller 0 (CM#0) for single controller type. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 63 EMEA&I.) Connect the connector of the LAN cable to the RMT port of the controller 0 (CM#0) and controller 1 (CM#1). FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 64: Host Interface Connection
When disconnecting the FC cable, pull out the connector while holding its tab. This section describes dual controller type as an example. Note that there is only controller 0 (CM#0) for single controller type. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 65 When connecting the FC cables, position them so that they will not obstruct replacement of the power supply unit or controllers by the maintenance engineer. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 66: Lan Cable Connection (For Iscsi)
When disconnecting LAN cables, depress the tab, then pull out the connector. This section describes dual controller type as an example. Note that there is only controller 0 (CM#0) for single controller type. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 67: Minisas Cable Connection (For Sas)
Connect the ETERNUS DX Disk storage system to the server using miniSAS cables. MiniSAS cables (ETERNUS DX Disk storage system connector: SFF8088) must be obtained separately. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 68 Insert the miniSAS cable connectors in the controller 0 (CM#0) and controller 1 (CM#1) SAS ports. Do not connect this cable to the DI (OUT) port. IMPORTANT FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 69: Drive Enclosure Connection
Connector for connecting DI (OUT) port DI (IN) of drive enclosure: Attach the connector with the symbol to the port. DI (IN) port Connector for connecting DI (IN) port FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 70 Connect the plug to be connected to DI (OUT) port, to the DI (OUT) port of the Controller 0 (CM#0). Remove the port cover from the DI (OUT) port before inserting the plug. Controller enclosure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 71 Do not connect anything to the SAS (OUT) port on the end edge. IMPORTANT ■ For single controller type EXP#0 Drive Enclosure CM#0 Controller Enclosure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 72: Power Synchronized Unit Connection
To help with power cord management and prevent incorrect connections, IMPORTANT attach labels to the power cords and make a note of connection origins and destinations. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 73 Wrap the release tie around the power cord and fasten the release tie from either side. Make sure that the release tie is not loose. Release tie FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 74: When 1U Power Distribution Unit Is Installed (For Regions Other Than Emea&I)
Procedure Remove the power cord clamp from the power distribution unit. Power cord clamps Power distribution unit FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 75 Power supply failure can be prevented by connecting the power IMPORTANT cords (AC input cables) on the power distribution unit A side and the power distribution unit B side to different power sources. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 76: When 2U Power Distribution Unit Is Installed (For Regions Other Than Emea&I)
To help with power cord management and prevent incorrect connections, IMPORTANT attach labels to the power cords and make a note of connection origins and destinations. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 77 PSU#0 inlets of the ETERNUS DX Disk storage : Connect between the OUTn of the power distribution unit B and the PSU#1 inlets of the ETERNUS DX Disk storage FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 78 (AC input cables) on the power distribution unit A side and the power distribution unit B side to different power sources. AC input cables Connect to power outlets. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 79 Main Line switch AC power is supplied to the enclosure, and the STATUS LED of the power supply units emit a green light. End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 80: Chapter 5 Setup
LAN cable and then connect it to the PC terminal. • If the LAN cable from the MNT port is connected to Controller 1 (CM#1), disconnect the LAN cable. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 81: Powering On
When a drive enclosure is installed, the power turns on automatically. Power switch Drive Enclosure Controller Enclosure After about three minutes, check that the READY LED on the controller enclosure are lit up. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 82 Master LED of Controller 0 (CM#0) is on. If the Master LED of Controller 1 (CM#1) is on for a dual-controller type, use the MNT port of Controller 1 (CM#1). End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 83: Start Up Eternus Web Gui
Type the following User name and Password, and click the [Logon] button. Username: root Password: root (default) After logging in, the device status screen of ETERNUS Web GUI appears. End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 84: Initial Setup
Click the [Initial Setup] menu on the [Easy Setup] tab. The Start screen of the [Initial Setup] function appears. Click the [Next>] button. The [Set Date and Time] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 85 The information that is set here is used for network management by SNMP. The name of the ETERNUS DX Disk storage system is displayed in the logon and operation screens of ETERNUS Web GUI. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 86 Specify the required items in [Set Password], and click the [Next>] button. A confirmation screen appears. Click the [OK] button. The password is changed, and the [Set Port Parameters] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 87 Select a port and specify the required items in "Port Settings", and click the [Next>] button. A confirmation screen appears. Click the [OK] button. The port parameters are set, and the [Setup Network Environment] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 88 Select a port and specify the required items in "Select Port", and click the [Next>] button. A confirmation screen appears. Click the [OK] button. The port parameters are set, and the [Setup Network Environment] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 89 Controller Enclosure's IP RESET Switch twice in succession within a two second interval will reset it to its factory default settings, and reallow network access. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 90 ETERNUS DX Disk storage system. A confirmation screen appears. Click the [OK] button. The Network Environment is set, and the [Finish] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 91 Start the Web browser, and log on again with the new IP address to perform the configuration settings of the ETERNUS DX Disk storage system. End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 92: Configuration Wizard
"ETERNUS Web GUI User’s Guide. For details on the setting procedures, refer to "ETERNUS Web GUI User's Guide". Also refer to "Configuration Guide -Server Connection-" as required. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 93 Click the [Configuration Wizard] menu on the [Easy Setup] tab in ETERNUS Web GUI. The [Configuration Wizard] screen appears. Click the [Start] button. The Configuration Wizard starts. The [Create RAID Group] menu screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 94 Data may not be recovered if a disk fails because RAID0 configuration is not redundant. RAID1, RAID1+0, RAID5, RAID5+0, and RAID6 are recommended as the RAID level. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 95 Set the required items and click the [Create] button. The following is a setting example when "Create RAID Group (Disks are assigned automatically)" is selected. A confirmation screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 96 Contact your sales representative or maintenance engineer if disks that are installed by default need to be uninstalled or moved to another slot. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 97 Setting screens will vary depending on the ETERNUS DX Disk storage system model. When the Host Affinity function is not used, the host setting is not IMPORTANT required. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 98 Click the [Next>] button. A confirmation screen appears. Click the [OK] button. The settings are reflected and the [Configure Affinity Group] screen in Step 5 appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 99 Click the [Next>] button. A confirmation screen appears. Click the [OK] button. The settings are reflected and the [Configure Affinity Group] screen in Step 5 appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 100 Click the [Next>] button. A confirmation screen appears. Click the [OK] button. The settings are reflected and the [Configure Affinity Group] screen in Step 5 appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 101 Click the [OK] button. The affinity group is created, and the affinity group list is displayed. Click the [Next>] button. The [Define LUN Mapping] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 102 Set other affinity groups as required. Click the [Finish] button. The settings are reflected, and a message to confirm finishing the Configuration Wizard appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 103 Click the [OK] button. Returns to the screen of "Port List" in Step (1). Click the [Finish] button. A message to confirm finishing the Configuration Wizard appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 104: Assign Hot Spare
When registering dedicated hot spares, the capacity of each hot spare should be the same as that of the capacity of the disks in the RAID group. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 105 In the ETERNUS Web GUI screen, click [Assign Hot Spare] under the [RAID Group Management] menu on the [Volume Settings] tab. The [Assign Hot Spare] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 106: Figure 5.2 The [Assign Hot Spare] Screen
This ends the basic settings of the ETERNUS DX Disk storage system. If further setup is necessary, refer to "ETERNUS Web GUI User's Guide". FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 107: Eternus Dx Disk Storage System Monitoring Setup
Click [Setup Event Notification] under the [System Settings] menu on the [Global Settings] tab in the ETERNUS Web GUI screen. The [Setup Event Notification] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 108 The [Error Severity Level] screen appears. Select the necessary items in "Error Severity Level". Click the "Warning Level" link. The [Warning Level] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 109 The [Informational Level] screen appears. Select the necessary items in "Informational Level". After finishing the necessary settings, click the [Set] button. A confirmation screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 110: Setup E-Mail Notification
Select "Enable" in "Notification E-Mail". • Specify the E-mail destination address in "Destination E-Mail Address". Click the "Mail Server Settings" link. The [Mail Server Settings] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 111: Snmp Trap Setup
Carefully read this manual and the manuals that are supplied with the IMPORTANT monitoring software (SNMP Manager) that is to be used before monitoring the ETERNUS DX Disk storage system. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 112 Enter the default gateway and any "Allowed IP List" devices. A confirmation screen appears. Click the [OK] button. The network environment is set, and the [Setup Network Environment] screen is closed. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 113 When changing SNMPD, click the [Switch] button. A confirmation screen appears. Click the [OK] button. Reboot the ETERNUS DX Disk storage system. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 114 "LAN Port used for SNMP". Set community (1) Click the [Community Name] link on the left of the screen. The community setting screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 115 (1) Click the [MIB View Setting] link on the left of the screen. The MIB view setting screen appears. (2) Specify the MIB view name, specify the subtree, and click the [Add New MIB View] button. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 116 (3) Confirm that the added destination for the SNMP Trap is displayed in the "Set Destination of SNMP Traps" field. Click the [Set] button. A confirmation screen appears. Click the [OK] button. The settings are reflected. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 117 (1) Click the [Manager] link on the left of the screen. The manager setting screen appears. (2) Click the [Add] button in the "Manager List" field. The "Set Manager" field appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 118 (1) Click the [MIB View] link on the left of the screen. The MIB View setting screen appears. (2) Click the [Add] button in the "MIB View List" field. The "Set MIB View" field appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 119 (1) Click the [User] link on the left of the screen. The user setting screen appears. (2) Click the [Add] button in the "User List" field. The "Set User" field appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 120 (3) Enter the community name for "Community Name", specify the IP address for the SNMP Manager for "Allowed SNMP Manager", and click the [OK] button. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED...
Page 121 Click the [Download MIB File] under the [Network Settings] menu on the [Global Settings] tab in the ETERNUS Web GUI screen. The [Download MIB File] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 122 Register the file that was downloaded in Step 4 of "ETERNUS DX Disk storage system settings" as the extended MIB definition file for the monitoring software. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 123 The [Perform SNMP Trap Test] screen appears. Click the [Send] button. A confirmation screen appears. Click the [OK] button. The SNMP Trap Test is performed. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 124: Remote Support Setup (For Regions Other Than Emea&I)
Click [Setup Remote Support] under the [Remote Support] menu on the [Global Settings] tab in the ETERNUS Web GUI screen. The [Setup Remote Support] screen appears. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 125: Connection Setup For The Eternus Dx Disk Storage System And Power Synchronized Units
Refer to "User's Guide -Power Synchronized Unit-" that is provided with the power synchronized unit for the required settings to use power control by connecting power synchronized units to an ETERNUS DX Disk storage system. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 126: Server Connection Setup
On the device tree in the left of the Storage System Status screen, components whose status is have a failure or require preventive maintenance. Contact your sales representative or maintenance engineer. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 127 On the RAID Group Status screen of ETERNUS Web GUI, the status of RAID groups that you have registered is displayed. Check if RAID configuration is set correctly. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED...
Page 128: Completion Of The Eternus Dx Disk Storage System Setup And Power Off
Press the Power switch to turn off the ETERNUS DX Disk storage system. • Via the power synchronized unit Use the power synchronized unit to turn off the ETERNUS DX Disk storage system. FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 129 When the power is turned off, the POWER LED will go out. When a drive enclosure is installed, the power turns off automatically. End of procedure FUJITSU Storage ETERNUS DX60 S2 Disk storage system User’s Guide -Installation- Copyright 2014 FUJITSU LIMITED P3AM-5502-05ENZ0...
Page 130 However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. •...