Intermec Sabre 1552 Scanner System Manual page 170

Sabre 1552 Scanner and MicroBar 9745 Base Station System Manual
programming bar codes (continued)
transmission rate, 2-14
Turbo mode, 2-11
turning off Aux Data Formatter, 3-23
turning on Aux Data Formatter, 3-23
UCC/EAN-128, 5-14
UPC A
check digit, transmitting, 5-18
defaulting settings, 5-18
number system, transmitting, 5-19
turning off, 5-18
turning on, 5-18
UPC E0
check digit, transmitting, 5-19
defaulting settings, 5-19
number system, transmitting, 5-20
turning off, 5-19
turning on, 5-19
version E expand, 5-20
UPC E1, 5-20
volume, setting beep, 4-5
wand emulation selections, 2-14–2-15
word length data bits, 3-5, 3-10
word length stop bits, 3-5, 3-10
See also bar codes
programming protocols, Burst protocol, 3-11
protocol, 8-11
protocol selection, 3-11
PS/2 compatibles interface keys, 6-5
Q, R
Quick Start defaults, 8-10
radio specifications, 8-5
radius of scanner from base, 1-3
rate of data transmission, 1-14
rate, scan, 8-3
rates, data, 8-5
reassociating scanner to base station, 1-10, 1-16
Record Ack/Nak protocol, 3-11
Record protocol, 3-11
red LED on battery pack, 1-6
regulatory compliance, 1-14
reliability, 8-5
removed scanner from base station network, 1-16
removing scanner from base station, 4-5
replacing
battery pack, 7-5
interface cable, 7-4
requiring
Aux Data Formatter, 3-23
data format, 4-20
reset factory settings, 2-18
response time, 8-5
retail symbologies, 5-16–5-22
RF compliance, 1-14
I-12
RF module operation, 1-14
RS-232
connector, host, 8-8
industrial interface, 2-4
interface, connecting, 1-9
port, auxiliary, 8-7
S
Sabre 1552 Cordless Scanner, See scanner
safety information, xi
saving
Aux Data Format Editor changes, 3-23
aux prefix and suffix changes, 3-17
data format changes, explained, 4-17
Data Format Editor changes, 4-20
prefix and suffix changes, 4-14
scan map, 8-9
scan rate, 8-3
scanner
accessories, 1-7
application work group selection, 4-4
assembly, 1-15
associating to base station, 1-10
associating up to nine scanners, 1-11
attaching the battery pack, 1-6
attaching to a tool balancer, 1-7
basic operation, 1-14
Battery Conservation mode, 2-16
battery pack, 1-5–1-6
beeps, 1-12
belt holster, described, 1-7
cleaning the scan window, 7-3
confirming data transmission, 1-17
coverage, 1-3
Decode Beep Selection, 4-7
green and yellow LEDs light, 1-16
head cover, described, 1-7
housing, examining, 7-3
illustrated, 1-4
laser marker beam, 4-8
LEDs, 1-6, 1-12
maintenance, 7-3–7-5
moving back into range, 1-16
out of range of base station, 1-16
pitch, setting beep, 4-6
radius from base, 1-3
reassociating to base station, 1-10, 1-16
removed from base station network, 1-16
removing from base station, 4-5
scan map, 8-9
setting up the Cordless System, 1-8–1-10
software revision, showing, 2-19
specifications, 8-3
three beeps, 1-11
troubleshooting, 7-6–7-7