Intermec Sabre 1552 Scanner System Manual page 164

Sabre 1552 Scanner and MicroBar 9745 Base Station System Manual
Code 39 (continued)
message length
maximum, 5-6
minimum, 5-6
sample bar code, A-5
start/stop characters, transmitting, 5-6
turning off, 5-6
turning on, 5-6
Code 93
default settings, 8-13
defaulting settings, 5-9
message length
maximum, 5-9
minimum, 5-9
sample bar code, A-5
turning off, 5-9
turning on, 5-9
Code ID prefix
configuring, 4-9
default setting, 8-12
symbology chart, 4-9, 4-14
commands
Aux Data Format Editor, 3-20
Data Format Editor, 4-17
communicating with host, 1-17–1-18
communications
auxiliary port, 3-8–3-14
default settings, 8-11
host port, 3-3–3-8
concatenation, Codabar
configuring, 5-5
default settings, 8-13
connecting scanner to base station, 1-10
connecting up to nine scanners, 1-11
connector
auxiliary RS-232/wand emulation, 8-7
keyboard/terminal and RS-232, 8-8
power, 8-8
conserving battery pack, 2-16
contacting Intermec, ii
contrast, print, 8-3
Control+ASCII mode, 2-11
Cordless Base Station, See base station
Cordless Scanner, See scanner
Cordless System
accessories, 1-7
associating scanner to base station, 1-10
associating up to nine scanners, 1-11
basic operation, 1-13–1-17
communicating with host, 1-17–1-18
described, 1-3
features, 1-3
keyboard function relationship table, 6-3
maintenance, 7-3–7-5
setting up, 1-8–1-10
I-6
Cordless System (continued)
troubleshooting, 7-6–7-7
See also base station
See also scanner
cords and connectors, inspecting, 7-3
country code, default, 8-10
country selection, keyboard, 2-9
D
data bits, word length, 3-5, 3-10, 8-11
data character, 8-11
data character selection, 3-13
data format
adding a data format, 4-16
adding an auxiliary, 3-18
alternates, 4-21
clearing all, 4-19
clearing one, 4-19
clearing one data format, explained, 4-17
default setting, 8-12
defaulting data format, 4-19
discarding changes, 4-20
discarding changes, explained, 4-17
entering data format, 4-19
industrial interface, aux port, 2-4
miscellaneous commands, 4-18
Move commands, 4-18
requiring, 4-20
saving changes, 4-20
saving, explained, 4-17
Search commands, 4-18
selections, 4-15–4-21
Send commands, 4-17
showing, 4-21
turning off, 4-20
turning on, 4-20
data rates, 8-5
data transmission, confirming, 1-17
data transmission, rate of, 1-14
decode beep
default, 8-12
selection, 4-7
decoding range from base, 1-3
defaulting
application work groups, 2-18
Aux Data Format, 3-22
auxiliary port communications, 3-8
auxiliary prefix, 3-16
auxiliary suffix, 3-17
Codabar settings, 5-3
Code 11 settings, 5-13
Code 2 of 5 settings, 5-11
Code 39 settings, 5-6
Code 93 settings, 5-9
data format, 4-19