Intermec Sabre 1552 Scanner System Manual page 169

programming bar codes, Code 39 (continued)
mimimum message length, 5-6
off, 5-6
on, 5-6
start/stop characters, 5-6
Code 93
defaulting settings, 5-9
maximum message length, 5-9
minimum message length, 5-9
turning off, 5-9
turning on, 5-9
Code ID prefix, 4-9
Control + ASCII mode, 2-11
data format
requiring, 4-20
turning off, 4-20
turning on, 4-20
Decode Beep Selection, 4-7
defaulting
Aux Data Format Editor, 3-22
aux prefix, 3-16
aux suffix, 3-17
data format, 4-19
prefix, 4-13
suffix, 4-13
discarding
Aux Data Format Editor changes, 3-23
Data Format Editor changes, 4-20
prefix and suffix changes, 4-14
EAN/JAN 13
check digit, transmitting, 5-17
defaulting settings, 5-16
turning off, 5-17
turning on, 5-17
EAN/JAN 8
check digit, transmitting, 5-17
defaulting settings, 5-16
turning off, 5-16
turning on, 5-16
EAN/UPC addenda
EAN, two and five digit, 5-21
requiring, 5-21
UPC, two and five digit, 5-22
Emulate External Keyboard, 2-11
entering Aux Data Format, 3-22
entering data format, 4-19
EOB data character, 3-14
EOR data character, 3-13
hardware flow control, 3-6, 3-13
host ACK selection, 3-7
IBM 4683 async address selections, 3-12
intercharacter delay, 2-13
interfunction delay, 2-13
programming bar codes (continued)
Interleaved 2 of 5
check digit, transmitting, 5-11
check digit, validating, 5-10
defaulting settings, 5-10
lengths of 6, 14, or 16, 5-11
maximum message length, 5-10
minimum message length, 5-10
turning off, 5-10
turning on, 5-10
intermessage delay, 2-13
ISBN, 5-18
keyboard
country selection, 2-9
style modifiers, 2-11
style selections, 2-10
laser marker beam, 4-8
Matrix 2 of 5
maximum message length, 5-12
minimum message length, 5-12
turning off, 5-12
turning on, 5-12
Numeric Keypad mode, 2-12
output delays selections, 2-13
output polarity, 2-15
parity, 3-4, 3-9
pitch, setting beep, 4-6
plug and play, 2-4–2-6
power settings, 2-16–2-17
programming chart, A-3
protocol selection, 3-11
Record Ack/Nak protocol, 3-11
Record protocol, 3-11
regular keyboard style, 2-10
requiring Aux Data Formatter, 3-23
saving
Aux Data Format Editor changes, 3-23
Data Format Editor changes, 4-20
prefix and suffix changes, 4-14
scanner software revision, showing, 2-19
scanner voting, 4-7
serial wedge output, 3-6
Shift Lock, 2-10
showing data format, 4-21
SOB data character, 3-14
SOR data character, 3-13
Telepen
alphanumeric, 5-16
defaulting settings, 5-15
maximum message length, 5-15
minimum message length, 5-15
numeric only, 5-16
turning off, 5-15
turning on, 5-15
I
Index
I-11