Lucent Technologies PARTNER Advanced Communications System Programming And Use Instructions page 481

Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11
TO START SYSTEM TO END SYSTEM PROGRAMMING:
PROGRAMMING:
PRESS
PRESS
Feature 0 0
TO USE A SPECIFIC PROCEDURE:
PRESS
System Program
DIAL
PRESS
Example:
System Program
System
SYSTEM DATE
(p. 5-259]
DIAL #101
DIAL the date in MMDDYY form
SYSTEM DAY
(p. 5-260)
[
2.0 or earlier
DIAL #102
DIAL 1 5
= Sunday = Thursday
6
2
= Monday = Friday
7
3 = Saturday
= Tuesday
4
= Wednesday
SYSTEM TIME (p. 5-268]
D I A L #103
the time in HHMM 24-hour
D I A L
military format
NUMBER OF LINES
(p. 5-202)
DIAL #104
DIAL two digits (01-24) for the
number of outside lines to be
assigned to every extension
3 per ACS processor module
& 308EC module
2 per 208 or 200 module
4 per 400 module
WARNING: Do not use Number of
Lines (#104) after initial setup. In Key
mode, the Number of Lines procedure
will change Line Assignment (#301),
Line Access Restriction (#302),
Automatic Line Selection and Line
Ringing to factory settings. To change
line assignments without affecting
other settings, use Line Assignment
(#301).
In Hybrid mode, the Number of Lines
procedure will change Pool Line
Assignment (#207), Pool Extension
Assignment (#314), and Pool Access
Restriction (#315). Additionally,
it changes Line Assignment (#301),
Line Access Restriction (#302),
Automatic Line Selection, and Line
Ringing. To change pool assignments
without affecting other settings, use
Pool Line Assignment (#207) and
Pod Extension Assignment (#314).
TRANSFER RETURN RINGS
(p. 5-273)
#105
D I A L
DIAL one digit (0–9) for the nurnber
of rings before the call returns
0-9 rings
4 rings
0 rings = no return
RECALL TIMER DURATION
(p. 5-226)
DIAL #107
DIAL two digits (01–80) to set the
length of a switchhook flash
= 18 (450 msec)
System Programming Quick Reference
Feature 0 0
and three-digit procedure code
#
for System Date
# 1 0 1
ROTARY DIALING TIMEOUT
(p. 5-236)
DIAL #108
DIAL 1 = 4 sec
2 = 8 sec
3 = 12 sec
]
OUTSIDE CONFERENCE DENIAL
(p. 5-209)
#109
DIAL
DIAL 1 = Allowed
2 = Disallowed
AUTOMATIC SYSTEM ANSWER
DELAY (p. 5-28)
DIAL #110
DIAL a ring delay number (0-9)
= 2 rings
AUTOMATIC SYSTEM ANSWER [
BUTTON
(p.. 5-25)
DIAL #111
DIAL 1 = Assigned
2 = Not Assigned
3 = Select Button then press
a programmable button
DIRECT EXTENSION DIAL DELAY [
(p. 5-102)
DIAL #112
DIAL a ring delay number (0-9)
2 rings
0 rings = answered immediately
DIRECT EXTENSION DIAL BUTTON
(p. 5-99)
DIAL #113
DIAL 1 = Assigned
2 = Not Assigned
3 = Select Button then press
a programmable button
OUTGOING CALL RESTRICTION
BUTTON
(p. 5-206)
DIAL #114
1 = Assigned
D I A L
2 = Not Assigned
3 = Select Button then press
a programmable button
WAKE UP SERVICE BUTTON
DIAL #115
(p. 5-294)
DIAL 1 = Assigned
2 = Not Assigned
3 = Select Button then press
a programmable button
(p. 5-50)
CALL COVERAGE RINGS
DIAL #116
DIAL 1-9
2
TO CYCLE THROUGH SYSTEM
PROGRAMMING PROCEDURES:
PRESS
Next Procedure
NOTES: Procedures #399, #609,
and #728—shown later in dashed
boxes—are skipped when cycling.
Lines
DIAL MODE
DIAL #201
DIAL a system line number
DIAL 1 = Touch-Tone
2 = Rotary
PRESS to program another line
Next Item
HOLD Disconnect TIME
DIAL #203
DIAL a system line number
DIAL 00 = No Detection
07 = 350 msec
01 = 50 msec
[ ] 02 = 100 msec 08 = 400 msec
2.0
03 = 150 msec 09 = 450 msec
04 = 200 msec 10 = 500 msec
05 = 250 msec
11 = 550 msec
06 = 300 msec
12 = 600 msec
PRESS to program another line
Next Item
] AUTOMATIC SYSTEM ANSWER
2.0
LINES
DIAL #204
DIAL a system line number
DIAL 1 = Assigned
2 = Not Assigned
PRESS to program another line
Next Item
]
2.0
DIRECT EXTENSION DIAL LINES
DIAL #205
DIAL a system line number
DIAL 1 = Assigned
2 = Not Assigned
PRESS to program another line
Next Item
[ ]
2.0
VMS COVER RINGS
DIAL
#117
DIAL 1-9
3
RING ON TRANSFER
DIAL #119
DIAL 1 = Active
2 = Not Active
AUTOMATIC SYSTEM ANSWER MODE
DIAL
#121
DIAL 1 = Hold
2 = Disconnect
3 = Ring
CALLER ID TYPE
[ ]
2.0 only
DIAL #122
DIAL 1 = USA
2 = Singapore
TO CYCLE THROUGH
AVAILABLE SETTINGS:
PRESS
or Next Data
Prev Procedure
TO RETURN TO FACTORY
SETTING:
PRESS
Remove
GROUP CALL DISTRIBUTION
(p. 5-98)
DIAL #206
DIAL a group number
(1–6, 7 for VMS)
DIAL a system line number
DIAL 1 = Assigned
2 = Not Assigned
3 = VMS Line Cover (only
for Hunt Group 7)
(p. 5-157)
PRESS
Next Item
POOL LINE ASSIGNMENT
DIAL #207
DIAL a system line number
DIAL 1 = No Pool
2 = Main Pool 880
3 = Pool 881
4 = Pool 882
5 = Pool 883
PRESS
Next Item
[ ]
2.0
(p. 5-30)
LINE COVERAGE EXTENSION
DIAL #208
DIAL a system line number
a system extension number
No lines owned by an extension
PRESS
Next Item
PRESS
Remove
(p. 5-104)
[ ]
2.0
UNIQUE LINE RINGING
DIAL #209
DIAL a system line number
DIAL 1
2-8
BACKUP PROGRAMMING —
AUTOMATIC
(p. 5-282)
DIAL #123
[ ]
2.0 or earlier
DIAL 1 = Active
2 = Not Active
3 = Backup Alarm Cleared
BACKUP PROGRAMMING—
(p. 5-235)
MANUAL
DIAL #124
PRESS
Enter
RESTORE PROGRAMMING
DIAL #125
(p. 5-32)
DIAL 1 = MAN.mmddyy
[ ]
2.0
2 = AUTO.mmddyy
PRESS
Enter
AUTOMATICDAYLIGHT/
(p. 5-83)
STANDARD TIMES
DIAL #126
DIAL 1 = Active
2 = Not active
or
Prev Data
(p. 5-143)
to program another line
[ ]
2.0
(p. 5-220)
to program another line
(p. 5-177)
to program another line
to unassign ownership
[ ]
3.0
(p. 5-279)
(p. 5-41)
(p. 5-44)
to begin the backup
(p. 5-232)
to begin the restore
[ ]
3.0
(p. 5-20)