Konica Minolta bizhub C658 Service Manual page 32

17. MECHANICAL ADJUSTMENT PC-115/PC-215..................................................................................................I-524
17.1 Paper reference position .................................................................................................................................................... I-524
17.1.1 Purpose ..................................................................................................................................................................... I-524
17.1.2 Procedure .................................................................................................................................................................. I-524
18. MECHANICAL ADJUSTMENT PC-410 ...............................................................................................................I-525
18.1 Paper reference position .................................................................................................................................................... I-525
18.1.1 Purpose ..................................................................................................................................................................... I-525
18.1.2 Procedure .................................................................................................................................................................. I-525
18.2 Shifter movement timing belt adjustment ........................................................................................................................... I-525
18.2.1 Procedure .................................................................................................................................................................. I-525
19. MECHANICAL ADJUSTMENT PC-415 ...............................................................................................................I-527
19.1 Paper reference position .................................................................................................................................................... I-527
19.1.1 Purpose ..................................................................................................................................................................... I-527
19.1.2 Procedure .................................................................................................................................................................. I-527
19.2 Shifter movement timing belt adjustment ........................................................................................................................... I-527
19.2.1 Procedure .................................................................................................................................................................. I-527
20. MECHANICAL ADJUSTMENT LU-207 ...............................................................................................................I-529
20.1 Paper feed section.............................................................................................................................................................. I-529
20.1.1 Changing the paper size............................................................................................................................................ I-529
20.1.2 Centering adjustment of the LCT............................................................................................................................... I-529
20.1.3 Pick-up roller load adjustment of the LCT ................................................................................................................. I-530
21. MECHANICAL ADJUSTMENT LU-302 ...............................................................................................................I-532
21.1 Paper feed section.............................................................................................................................................................. I-532
21.1.1 Centering adjustment of the LCT............................................................................................................................... I-532
21.1.2 Pick-up roller load adjustment of the LCT ................................................................................................................. I-532
22. MECHANICAL ADJUSTMENT PK-519 ...............................................................................................................I-534
22.1 Punch section ..................................................................................................................................................................... I-534
22.1.1 Punch hole deviation correction ................................................................................................................................ I-534
23. MECHANICAL ADJUSTMENT PK-520 ...............................................................................................................I-536
23.1 Punch section ..................................................................................................................................................................... I-536
23.1.1 Punch hole deviation correction ................................................................................................................................ I-536
24. MECHANICAL ADJUSTMENT PK-523 ...............................................................................................................I-538
24.1 Punch section ..................................................................................................................................................................... I-538
24.1.1 Punch hole deviation correction ................................................................................................................................ I-538
25. MECHANICAL ADJUSTMENT FS-534SD ..........................................................................................................I-539
25.1 Paper exit section ............................................................................................................................................................... I-539
25.1.1 Half-fold skew adjustment ......................................................................................................................................... I-539
26. MECHANICAL ADJUSTMENT FD-536SD saddle section ..................................................................................I-541
26.1 Paper exit section ............................................................................................................................................................... I-541
26.1.1 Half-fold skew adjustment ......................................................................................................................................... I-541
27. MECHANICAL ADJUSTMENT FS-537SD saddle section ..................................................................................I-543
27.1 Paper exit section ............................................................................................................................................................... I-543
27.1.1 Half-fold skew adjustment ......................................................................................................................................... I-543
J REWRITING OF FIRMWARE ........................................................................................................ J-1
1. REWRITING OF FIRMWARE ...................................................................................................................................J-1
2. Confirming the firmware version ................................................................................................................................J-2
2.1 Procedure ................................................................................................................................................................................ J-2
3. USB memory .............................................................................................................................................................J-3
3.1 Preparation .............................................................................................................................................................................. J-3
3.1.1 System preparation ........................................................................................................................................................ J-3
3.1.2 USB memory used to update firmware........................................................................................................................... J-3
3.1.3 Directory configuration of USB memory ......................................................................................................................... J-3
3.2 Procedure ................................................................................................................................................................................ J-3
3.3 Action when data transfer fails................................................................................................................................................. J-5
4. Internet ISW...............................................................................................................................................................J-6
4.1 Outline ..................................................................................................................................................................................... J-6
4.2 Service environment ................................................................................................................................................................ J-6
4.3 Preparations for firmware rewriting.......................................................................................................................................... J-6
4.3.1 Internet ISW Set ............................................................................................................................................................. J-6
4.3.2 Protocol setting............................................................................................................................................................... J-6
xxxi