YASKAWA GA800 Maintenance & Troubleshooting page 207

No.
Name
(Hex.)
H2-25 Comparator 1 Off-Delay
Time
(1545)
H2-26 Comparator 2 Monitor
Selection
(1546)
H2-27 Comparator 2 Lower Limit
(1547)
H2-28 Comparator 2 Upper Limit
(1548)
H2-29 Comparator 2 Hysteresis
(1549)
H2-30 Comparator 2 On-Delay
Time
(154A)
H2-31 Comparator 2 Off-Delay
Time
(154B)
H2-32 Comparator 1 Filter Time
(159A)
H2-33 Comparator1 Protection
Selection
(159B)
H2-34 Comparator 2 Filter Time
(159C)
H2-35 Comparator2 Protection
Selection
(159D)
H2-36 Comparator 1 Ineffective
Time
(159E)
H2-37 Comparator 2 Ineffective
Time
(159F)
H2-40 Mbus Reg 15E0h bit0
Output Func
(0B58)
H2-41 Mbus Reg 15E0h bit1
Output Func
(0B59)
H2-42 Mbus Reg 15E0h bit2
Output Func
(0B5A)
H2-60 Term M1-M2 Secondary
Function
(1B46)
Expert
H2-61 Terminal M1-M2 Logical
Operation
(1B47)
Expert
H2-62 Terminal M1-M2 Delay
Time
(1B48)
Expert
YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
V/f CL-V/f OLV CLV AOLV
Sets the off-delay time for comparator 1.
V/f CL-V/f OLV CLV AOLV
Sets the monitor number for comparator 2. Set the x-xx part of the Ux-xx [Monitor]. For example, set
H2-26 = 103 to monitor U1-03 [Output Current].
V/f CL-V/f OLV CLV AOLV
Sets the lower limit detection level for comparator 2 as a percentage of the full scale analog output
for the monitor selected in H2-26 [Comparator 2 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets the upper limit detection level for comparator 2 as a percentage of the full scale analog output
for the monitor selected in H2-26 [Comparator 2 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets the hysteresis level for comparator 2 as a percentage of the full scale analog output for the
monitor selected in H2-26 [Comparator 2 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets the on-delay time for comparator 2.
V/f CL-V/f OLV CLV AOLV
Sets the off-delay time for comparator 2.
V/f CL-V/f OLV CLV AOLV
Sets the time constant that is applied to the primary delay filter used for the analog output of the
monitor selected with H2-20 [Comparator 1 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets drive operation when it detects CP1 [Comparator1 Limit Fault].
0 : Ramp to Stop
1 : Coast to Stop
2 : Fast Stop (Use C1-09)
3 : Alarm Only
4 : Digital Output Only
V/f CL-V/f OLV CLV AOLV
Sets the time constant that is applied to the primary delay filter used for the analog output of the
monitor selected with H2-26 [Comparator 2 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets drive operation when it detects CP2 [Comparator2 Limit Fault].
0 : Ramp to Stop
1 : Coast to Stop
2 : Fast Stop (Use C1-09)
3 : Alarm Only
4 : Digital Output Only
V/f CL-V/f OLV CLV AOLV
Sets the length of time that CP1 [Comparator1 Limit Fault] is disabled.
V/f CL-V/f OLV CLV AOLV
Sets the length of time that CP2 [Comparator2 Limit Fault] is disabled.
V/f CL-V/f OLV CLV AOLV
Sets the MFDO for bit 0 of MEMOBUS register 15E0 (Hex.).
V/f CL-V/f OLV CLV AOLV
Sets the MFDO for bit 1 of MEMOBUS register 15E0 (Hex.).
V/f CL-V/f OLV CLV AOLV
Sets the MFDO for bit 2 of MEMOBUS register 15E0 (Hex.).
V/f CL-V/f OLV CLV AOLV
Sets the second function for terminal M1-M2. Outputs the logical calculation results of the terminals
assigned to functions by H2-01 [Term M1-M2 Function Selection].
V/f CL-V/f OLV CLV AOLV
Sets the logical operation for the functions set in H2-01 [Term M1-M2 Function Selection] and H2-
60 [Term M1-M2 Secondary Function].
V/f CL-V/f OLV CLV AOLV
Sets the minimum on time used to output the logical calculation results from terminal M1-M2.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
3.10 H: Terminal Functions
Default
(Range)
0.0 s
(0.0 - 600.0 s)
103
(000 - 999)
0.0%
(0.0 - 300.0%)
0.0%
(0.0 - 300.0%)
0.0%
(0.0 - 10.0%)
0.0 s
(0.0 - 600.0 s)
0.0 s
(0.0 - 600.0 s)
0.0s
(0.0 - 10.0 s)
4
(0 - 4)
0.0s
(0.0 - 10.0 s)
4
(0 - 4)
0.0 s
(0.0 - 1000.0 s)
0.0 s
(0.0 - 1000.0 s)
F
(0 - 1FF)
F
(0 - 1FF)
F
(0 - 1FF)
F
(0 - FF)
0
(0 - 8)
0.1 s
(0.0 - 25.0 s)
3
207