Mitsubishi Electric MELSEC iQ-R Series User Manual page 357

N
Condition target channel setting
. . . . . . . . . . . . . . . . . . 222
Condition target setting
Interrupt factor detection flag
Interrupt factor generation setting
. . . . . . . . . . . . . . . . . . . . 221
Interrupt factor mask
Interrupt factor reset request
Number of slave modules with inter-module peak
current suppression function enabled
Number of slave modules with inter-module
simultaneous temperature rise function enabled
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
P
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
P control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PD control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PI control
. . . . . . . . . . . . . . . . . . . . . . . . . . 14
PID constants
. . . . . . . . . . . . . . . . . . . . 226
PID continuation flag
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PID control
PID control forced stop command
Position proportional control
Q
CH1 Cooling method setting
. . . . . . . . . . . . . . . . . . . . . . 322
CT1 CT selection
During AT loop disconnection detection function
. . . . . . . . . . . . . . . . . . . . . . . . 295
enable/disable
Function extension bit monitor
Peak current suppression control group setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
. . . . . . . . . . . . . . . . . . . . . . 14
Q compatible mode
Sampling cycle and function extension setting
Sensor correction function selection
R
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
R mode
. . . . . . . . . . . . . . . . . 140
Refresh processing time
S
. . . . . . . . . . . . . . . . . . 215
Sampling cycle monitor
. . . . . . . . . . . . . . . . . 224
Sampling cycle selection
Setting change command
Setting change completion flag
Setting value backup command
Setting value backup completion flag
Setting value backup failure flag
Setting variation rate limiter setting selection
Setting variation rate limiter setting selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
monitor
Setting/operation mode command
Setting/operation mode status
Simultaneous temperature rise parameter
. . . . . . . . . . . . . . . . . . . . . . . . 15
Standard control
Start I/O of slave module with inter-module peak
current suppression function enabled
Start I/O of slave module with inter-module
simultaneous temperature rise function enabled
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
. . . . . . . . . . . . 223
. . . . . . . . . . . . . . 214
. . . . . . . . . . . 222
. . . . . . . . . . . . . . 221
. . . . . . . . 326
. . . . . . . . . . . 166
. . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . 279
. . . . . . . . . . . . . 330
. . 331
. . . . . . . . . 311
. . . . . . . . . . . . . . . . 166
. . . . . . . . . . . . . 162
. . . . . . . . . . . . 165
. . . . . . . . 160
. . . . . . . . . . . . 162
. . . 225
. . . . . . . . . . . 164
. . . . . . . . . . . . . 157
. . . . . . 14
. . . . . . . . 326
T
Temperature conversion completion flag
Temperature conversion completion flag
. . . . . . . . . . . . . . . . . . . .216
(Q-compatible mode)
Temperature conversion setting
Transistor output monitor ON delay time setting
. . . . . . . . . . . . . . . . . . . . . .18
Two-position control
U
Upper limit deviation alert
Upper/lower limit deviation alert
W
. . . . . . . . . . . . . . . . . . . . . . . .75
Within-range alert
. . . . . . .216
. . . . . . . . . . . . .276
. .227
. . . . . . . . . . . . . . . . . .74
. . . . . . . . . . . . . .75
355
I