Mitsubishi Electric MELSEC iQ-R Series User Manual page 197

Address: CH Setting details
Decimal
Standard
(hexadeci
control
mal)
110(6EH) CH3 Adjustment
sensitivity (dead
band) setting
111(6FH) CH3 Control output
cycle setting
112(70H) CH3 Primary delay digital filter setting
113(71H) CH3 Control
response
parameter
114(72H) CH3 AUTO/MAN
mode shift
115(73H) CH3 MAN output
setting
116(74H) CH3 Setting variation
rate limiter/
setting variation
rate limiter
(temperature
*10
rise)
117(75H) CH3 AT bias
118(76H) CH3 Direct/reverse
action setting
119(77H) CH3 Upper limit
setting limiter
120(78H) CH3 Lower limit
setting limiter

121(79H) System area
122(7AH) CH3 Heater
disconnection
*11
alert setting
123(7BH) CH3 Loop
disconnection
detection
judgment time
124(7CH) CH3 Loop
disconnection
detection dead
band
125(7DH) CH3 Unused channel
setting
126(7EH) CH3 Memory's PID
constants read
command
127(7FH) CH3 Automatic
backup setting
after auto tuning
of PID constants
128(80H) CH4 Input range
129(81H) CH4 Stop mode
setting
130(82H) CH4 Set value (SV)
setting
131(83H) CH4 Proportional
band (P) setting
Heating- Mix control
cooling
control
Adjustment Adjustment
sensitivity (dead sensitivity (dead
*1
band) setting band) setting
Heating control Control output
output cycle cycle setting
*1
setting
Control Control
response response
*1
parameter parameter
AUTO/MAN AUTO/MAN
*1
mode shift mode shift
MAN output MAN output
*1
setting setting
Setting variation Setting variation
rate limiter/ rate limiter/
setting variation setting variation
rate limiter rate limiter
(temperature (temperature
*1*10 *10
rise) rise)
*1
AT bias AT bias
System area Direct/reverse
action setting
Upper limit Upper limit
*1
setting limiter setting limiter
Lower limit Lower limit
*1
setting limiter setting limiter
System area Heater
disconnection
*11
alert setting
System area Loop
disconnection
detection
judgment time
System area Loop
disconnection
detection dead
band
Unused channel Unused channel
*1
setting setting
Memory's PID Memory's PID
constants read constants read
*1
command command
Automatic Automatic
backup setting backup setting
after auto tuning after auto tuning
of PID of PID constants
*1
constants
Stop mode Stop mode
*1
setting setting
Set value (SV) Set value (SV)
*1
setting setting
Heating Proportional
proportional band (P) setting
band (Ph)
*1
setting
Default Data
value type
Position-
proportional
control
Adjustment 5 Setting
sensitivity (dead
*5
band) setting
*15
System area 30 Setting
*16
300
0 Setting
Control 0 Setting
response
*5
parameter
System area 0 Setting
System area 0 Setting
Setting variation 0 Setting
rate limiter/
setting variation
rate limiter
(temperature
*5*10
rise)
*5
AT bias 0 Setting
Direct/reverse 1 Setting
*5
action setting
Upper limit 1300(TCTRT Setting
*5
setting limiter )
6000(TCRT)
Lower limit 0(TCTRT) Setting
*5
setting limiter -2000(TCRT)
 
System area 0 Setting
System area 480 Setting
System area 0 Setting
Unused channel 0 Setting
*5
setting
Memory's PID 0 Setting
constants read
*5
command
Automatic 0 Setting
backup setting
after auto tuning
of PID
*5
constants
2(TCTRT) Setting
7(TCRT)
Stop mode 1 Setting
*5
setting
Set value (SV) 0 Setting
*5
setting
Proportional 30 Setting
band (P)
*5
setting
Appendix 3 Buffer Memory Areas
(1) (2) (3) (4) (5)
    
    
    
    
    
    
    
    
    
    
    
A
    
    
    
    
    
    
    
    
    
    
    
APPX
195