ProMinent DULCOMETER diaLog DACb Assembly And Operating Instruction page 189
Multi-parameter controller
Hide thumbs
Also See for DULCOMETER diaLog DACb:
- Assembly and operating instructions manual (180 pages)
Table of Contents
Advertisement
Question: What should I consider when
connecting passive monitors? . . . . . . . . 155
Question: What sort of applications are
there? . . . . . . . . . . . . . . . . . . . . . . . 26
Question: What spare parts are there? . . . 179
Question: What type of buffer solutions do
I need for a fluoride calibration? . . . . 100, 102
Question: What type of buffer solutions do
I need for pH calibration? . . . . . . . . . . . . 86
Question: What type of equipment does
the controller have as standard? . . . . . . . 26
Question: Where can I find the Declaration
of Conformity? . . . . . . . . . . . . . . . . . 186
Question: Where do I find the [Simulation]
function? . . . . . . . . . . . . . . . . . . . . . 166
Question: Which calibration process can
you use to calibrate amperometric meas‐
ured variables? . . . . . . . . . . . . . . . . . 104
Question: Which calibration process can
you use to calibrate the DO measured var‐
iable? . . . . . . . . . . . . . . . . . . . . . . . 110
Question: Which calibration process can
you use to calibrate the fluoride value? . . . 98
Question: Which calibration process can
you use to calibrate the ORP value? . . . . . 95
Question: Which calibration process can
you use to calibrate the pH value? . . . . . . 85
Question: Which components are included
as standard? . . . . . . . . . . . . . . . . . . . 33
Question: Which conductivity sensor can I
connect to the controller? . . . . . . . . . . . . 63
Question: Which standards are complied
with? . . . . . . . . . . . . . . . . . . . . . . . 186
Question: Which values render pH calibra‐
tion valid? . . . . . . . . . . . . . . . . . . . . . 86
R
Reducing inserts . . . . . . . . . . . . . . . . . 56
Remove and refit the fluoride sensor in the
in-line probe housing . . . . . . . . . . . 99, 101
Remove and refit the pH sensor in the in-
line probe housing . . . . . . . . . . . . . . . . 85
Run in periods . . . . . . . . . . . . . . 105, 107
S
Saving the unit configuration as a text file . . 29
SD cards . . . . . . . . . . . . . . . . . . . . . 159
Selection of the connected sensor . . . . . . 64
Sensor connector . . . . . . . . . . . . . . . . 63
Sensor function . . . . . . . . . . . . . . 105, 107
Service life of the SD card . . . . . . . . . . 159
Setting the mA outputs . . . . . . . . . . . . 155
Simulation . . . . . . . . . . . . . . . . . . . . 166
Spare parts units . . . . . . . . . . . . . . . . 180
Standard signal outputs . . . . . . . . . 105, 108
Standards complied with . . . . . . . . . . . 186
Strain relief . . . . . . . . . . . . . . . . . . . . 56
Swimming pool water treatment . . . . . . . . 26
T
Terminal diagrams showing 1:1 assignment 41
Test container 1 with buffer solution . . . . . 86
Test container 1 with fluoride calibration
solution . . . . . . . . . . . . . . . . . . . 99, 101
Test container 2 with buffer solution . . . . . 86
Test container 2 with fluoride calibration
solution . . . . . . . . . . . . . . . . . . . . . . . 99
The maximum file size is 2 GB . . . . . . . . 163
Threaded connector, large (M 20 x 1.5) . . . 56
Threaded connector, medium (M 16 x 1.5)
Threaded connector, small (M 12 x 1.5) . . . 56
Timer relay . . . . . . . . . . . . . . . . . . . . 151
U
Upgrade package . . . . . . . . . . . . . . . . 27
Uploading unit configuration file from the
SD card . . . . . . . . . . . . . . . . . . . . . . 31
Index
56
189
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the DULCOMETER diaLog DACb and is the answer not in the manual?
Questions and answers
How do I calibrate measuring channel
To calibrate a measuring channel on a ProMinent diaLog DACb:
1. Select the channel to be calibrated (e.g., Channel 1: Chlorine).
2. Access the [Calibration] menu from the continuous display.
3. Follow the on-screen instructions to perform the calibration.
4. Adjust the value using the appropriate buttons if prompted.
5. Import the calibration result into the controller memory by pressing the confirmation button.
6. The controller will return to the continuous display and use the new calibration values.
If calibration values are outside specified limits, an error message appears, and the calibration is not saved. In that case, check conditions, correct any issues, and repeat the calibration. Each measuring channel must be calibrated separately.
This answer is automatically generated