YASKAWA E1000 Technical Manual page 393

No. (Addr.) Name
U1-14
Terminal A2 Input Level
(4FH)
U1-15
Terminal A3 Input Level
(50H)
U1-16 Output Frequency after Soft
(53H) Starter
U1-18
oPE Fault Parameter
(61H)
U1-19 MEMOBUS/Modbus Error
(66H) Code
U1-24
Input Pulse Monitor
(7DH)
U1-25
Software Number (Flash)
(4DH)
U1-26
Software No. (ROM)
(5BH)
U1-29
Software No. (PWM)
(7AAH)
<18> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<19> This value's number of decimal places depends on the drive model. The value will have two decimal places (0.01 A) if the drive model is
CIMR-E2A0004 to 2A0040, 4A0002 to 4A0023 and one decimal place (0.1 A) if the drive model is CIMR-E2A0056 to 2A0415, 4A0031
to 4A1200.
<22> Drives with a maximum output up to 11 kW will display this value in units of 0.01 kW (two decimal places). Drives with a maximum output
greater than 11 kW will display this value in units of 0.1 kW (one decimal place).
for details.
<50> When reading the value of this monitor via MEMOBUS/Modbus a value of 8192 is equal to 100% of the drive rated output current.
■
U2: Fault Trace
No. (Addr.) Name
U2-01
Current Fault
(80H)
U2-02
Previous Fault
(81H)
U2-03 Frequency Reference at
(82H) Previous Fault
U2-04 Output Frequency at Previous
(83H) Fault
U2-05 Output Current at Previous
(84H) Fault
U2-07 Output Voltage at Previous
(86H) Fault
U2-08 DC Bus Voltage at Previous
(87H) Fault
U2-09 Output Power at Previous
(88H) Fault
YASKAWA ELECTRIC SIEP C710616 35D YASKAWA AC Drive E1000 Technical Manual
All Modes
Displays the signal level to analog input terminal A2.
All Modes
Displays the signal level to analog input terminal A3.
All Modes
Displays output frequency with ramp time and S-curves. Units determined by o1-03.
All Modes
Displays the parameter number that caused the oPE or Err (EEPROM write error) error.
All Modes
Displays the contents of a MEMOBUS/Modbus error.
YEC_
com -
mon
All Modes
Displays the frequency to pulse train input terminal RP.
All Modes
FLASH ID
All Modes
ROM ID
All Modes
PWM ID
Note: This parameter is displayed in models CIMR-E4A0930 and 4A1200.
All Modes
Displays the current fault.
All Modes
Displays the previous fault.
All Modes
Displays the frequency reference at the previous fault.
All Modes
Displays the output frequency at the previous fault.
All Modes
Displays the output current at the previous fault.
Note: The unit is expressed in 1 A for models CIMR-E4A0930 and 4A1200.
All Modes
Displays the output voltage at the previous fault.
All Modes
Displays the DC bus voltage at the previous fault.
All Modes
Displays the output power at the previous fault.
Description
CRC Error
Data Length Error
Not Used
Parity Error
Overrun Error
Framing Error
Timed Out
Not Used
Refer to Model Number and Nameplate Check on page 29
Description
B.3 Parameter Table
Analog Output
Unit
Level
common_
TMonly
10 V: 100% 0.1%
common_
TMonly
10 V: 100% 0.1%
common_
TMonly
10 V: Max frequency 0.01 Hz
common_
No signal output
TMonly
–
available
common_
TMonly
No signal output
–
available
common_
TMonly
Determined by H6-02 1 Hz
common_
No signal output
TMonly
–
available
common_
No signal output
TMonly
–
available
common_
TMonly
No signal output
–
available
Analog Output
Unit
Level
common_
No signal output
TMonly
–
available
common_
No signal output
TMonly
–
available
common_
No signal output
TMonly
0.01 Hz
available
common_
No signal output
TMonly
0.01 Hz
available
common_
TMonly
No signal output
<19> <50>
available
common_
No signal output
TMonly
0.1 Vac
available
common_
No signal output
TMonly
1 Vdc
available
common_
No signal output
TMonly
0.1 kW
available
Page
–
–
–
–
–
–
–
–
–
Page
–
–
–
–
–
–
B
–
–
393