Main Menu - Profibus - Group - Danfoss VLT Series Programming Manual

Parameter Description

3.10 Main Menu - Profibus - Group 9

9-15 PCD Write Configuration
Array [10]
Option:
3 3
[0] None
*
[302] Minimum Reference
[303] Maximum Reference
[341] Ramp 1 Ramp Up Time
[342] Ramp 1 Ramp Down Time
[351] Ramp 2 Ramp Up Time
[352] Ramp 2 Ramp Down Time
[380] Jog Ramp Time
[381] Quick Stop Ramp Time
[382] Starting Ramp Up Time
[411] Motor Speed Low Limit [RPM]
[413] Motor Speed High Limit [RPM]
[416] Torque Limit Motor Mode
[417] Torque Limit Generator Mode
[590] Digital & Relay Bus Control
[593] Pulse Out #27 Bus Control
[595] Pulse Out #29 Bus Control
[597] Pulse Out #X30/6 Bus Control
[653] Terminal 42 Output Bus Control
[663] Terminal X30/8 Output Bus
Control
[890] Bus Jog 1 Speed
[891] Bus Jog 2 Speed
[894] Bus Feedback 1
[895] Bus Feedback 2
[896] Bus Feedback 3
[1680] Fieldbus CTW 1
[1682] Fieldbus REF 1
[2013] Minimum Reference/Feedb.
[2014] Maximum Reference/Feedb.
[2021] Setpoint 1
[2022] Setpoint 2
[2023] Setpoint 3
[2643] Terminal X42/7 Bus Control
[2653] Terminal X42/9 Bus Control
88
®
VLT HVAC Drive Programming Guide
9-15 PCD Write Configuration
Array [10]
Function: Option:
Select the parameters [2663] Terminal X42/11 Bus Control
to be assigned to PCD
PB-16 PCD Read Configuration
3 to 10 of the
Array [10]
telegrams. The number
of available PCDs
Option:
depends on the
telegram type. The
values in PCD 3 to 10
will then be written to
the selected
parameters as data
values. Alternatively,
specify a standard
Profibus telegram in
9-22 Telegram Selection.
[0]
[894]
[895]
[896]
[1500] Operating Hours
[1501] Running Hours
[1502] kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
[1603] Status Word
[1605] Main Actual Value [%]
[1609] Custom Readout
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor Current
[1615] Frequency [%]
[1616] Torque [Nm]
[1617] Speed [RPM]
[1618] Motor Thermal
[1622] Torque [%]
[1630] DC Link Voltage
[1632] Brake Energy /s
[1633] Brake Energy /2 min
[1634] Heatsink Temp.
[1635] Drive Thermal
[1638] Logic Controller State
[1639] Control Card Temp.
[1650] External Reference
[1652] Feedback [Unit]
[1653] Digi Pot Reference
[1654] Feedback 1 [Unit]
[1655] Feedback 2 [Unit]
®
MG.11.CC.02 - VLT is a registered Danfoss trademark
None
*
Bus Feedback 1
Bus Feedback 2
Bus Feedback 3
Function:
Function:
Select the parameters to be
assigned to PCD 3 to 10 of
the telegrams. The number of
available PCDs depends on
the telegram type. PCDs 3 to
10 contain the actual data
values of the selected
parameters. For standard
Profibus telegram, see
9-22 Telegram Selection.