Power Jumper Contacts/Field Supply; Figure 4: Power Jumper Contacts; Table 8: Legend For The "Power Jumper Contacts" Figure - WAGO I/O-SYSTEM 750 Manual

24 Device Description
Pos : 34 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üss e/Leistungs kontakte/F el dvers orgung - Übersc hrift 3 @ 6\mod_1256294692864_21.doc x @ 43664 @ 3 @ 1
4.2.2

Power Jumper Contacts/Field Supply

Pos : 35.1 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Vorsic ht/Vorsicht: Verl etz ungsgefahr durc h s charfkantige M ess er kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 35.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte 2 LK (Mess er/Leis tungs kontakte 2 LK (Messer /Feder) - Ei nleitung @ 15\mod_1371721641099_21.doc x @ 123714 @ @ 1
The I/O module 750-644 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos : 35.3 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte 2 LK (Mess er/Leis tungs kontakte 2 LK (Messer /Feder) - Abbil dung (doppelte Br eite) @ 15\mod_1371721756578_21.doc x @ 123718 @ @ 1

Figure 4: Power jumper contacts

Pos : 35.4 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte 2 LK (Mess er/Leis tungs kontakte 2 LK (Messer /Feder) - Legende @ 15\mod_1371721352500_21.doc x @ 123710 @ @ 1

Table 8: Legend for the "Power jumper contacts" figure

Contact
1
2
3
4
Pos : 35.5 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Achtung/Achtung: M axi mal er Strom Leistungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current to flow through the power contacts is 10 A.
Greater currents can damage the power contacts.
When configuring the system, ensure that this current is not exceeded. If
exceeded, an additional potential feed module must be used.
Pos : 35.6 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Potenti alei ns peis ekl emme für Erde ei nsetzen! @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1
Type
Spring contact Potential transmission (U
Spring contact Potential transmission (0 V) for field supply
Blade contact
Blade contact
750-644 Bluetooth
Function
Potential feed-in (0 V) for field supply
Potential feed-in (U
v
Version 2.0.0, valid from FW/HW Version 03/03
WAGO-I/O-SYSTEM 750
®
RF-Transceiver
) for field supply
v
) for field supply
Manual