Wiring Peripheral Power Devices - gefran VDI100 Series Instruction Manual

Wire size
mm 2 (AWG)
14 (6)
22 (4)
30 / 38 (3 /2)
50 / 60 (1/1/0)
70 (2/0)
80 (3/0)
100 (4/0)
3.7.

Wiring Peripheral Power Devices

• After power is shut off to the inverter the capacitors will slowly discharge. Do NOT touch the inverter circuit
or replace any components until the "CHARGE" indicator is off.
Caution
• Do NOT wire or connect/disconnect internal connectors of the inverter when the inverter is powered up or
after power off but the "CHARGE"" indicator is on.
• Do NOT connect inverter output U, V and W to the AC power source. This will result in damage to the
inverter.
• The inverter must be properly grounded. Use terminal E to connect earth ground and comply with local
standards.
• It is required to disconnect the ground wire in the control board if the inverter is not grounded.
• Do NOT perform a dielectric voltage withstand test (Megger) on the inverter this will result in inverter dam-
age to the semiconductor components.
• Do NOT touch any of the components on the inverter control board to prevent damage to the inverter by
static electricity.
230V Class : 0.75~1.5 kW / 400V Class: 0.75~2.2 kW
Disconnect the ground wire of J1. on the control board (C/B).
VDI100 • Instruction manual
Terminal Model of the round
screw size crimp terminal
M4 R14-4
M5 R14-5
M6 R14-6
M8 R14-8
M6 R22-6
M8 R22-8
M6 R38-6
M8 R38-8
M8 R60-8
M10 R60-10
M8 R70-8
M10 R70-10
M10 R80-10
M16 R80-16
M10 R100-10
M12 R100-12
M16 R80-16
Model of insulating
Fastening torque
kgf.cm (in.lbs)
12.2 to 14 (10.4 to 12.1)
20.4 to 24 (17.7 to 20.8)
25.5 to 30.0 (22.1 to 26.0)
61.2 to 66.0 (53.0 to 57.2)
25.5 to 30.0 (22.1 to 26.0)
61.2 to 66.0 (53.0 to 57.2)
25.5 to 30.0 (22.1 to 26.0)
61.2 to 66.0 (53.0 to 57.2)
61.2 to 66.0 (53.0 to 57.2)
102 to 120 (88.5 to 104)
61.2 to 66.0 (53.0 to 57.2)
102 to 120 (88.5 to 104)
102 to 120 (88.5 to 104)
255 to 280 (221 to 243)
102 to 120 (88.5 to 104)
143 to 157 (124 to 136)
255 to 280 (221 to 243)
230V Class : 2.2~5.5 kW / 400V Class: 3.7~5.5 kW
Disconnect the ground wire of J1. on the control board (C/B).
Model of
sleeve crimp tool
TIC 14 NH 1 / 9
TIC 14 NH 1 / 9
TIC 14 NH 1 / 9
TIC 14 NH 1 / 9
TIC 22 NOP 60/ 150H
TIC 22 NOP 60/ 150H
TIC 38 NOP 60/ 150H
TIC 38 NOP 60/ 150H
TIC 60 NOP 60/ 150H
TIC 60 NOP 150H
TIC 60 NOP 150H
TIC 60 NOP 150H
TIC 80 NOP 150H
TIC 80 NOP 150H
TIC 100 NOP 150H
TIC 100 NOP 150H
TIC 80 NOP 150H
21