MIMAKI TS55-1800 Operation Manual page 113

Display
ERROR 402
MOTOR Y
ERROR 403
X CURRENT
ERROR 404
Y CURRENT
ERROR 44f
Take-up Roll Sns Err
ERROR 505
MEDIA JAM
ERROR 509
HDC POSCNT
ERROR 50a
Y ORIGIN
ERROR 50f
L-SCALE BLACK
ERROR 50c
MEDIA WIDTH SENSOR
ERROR 516
MEDIA SET POSITION R
ERROR 528
PUMP MOTOR SENSOR
ERROR 52f
CARRIAGE ORG
ERROR 530
STATION ORG
ERROR 536
STATION LOCK
ERROR 537
MAINT.WASH SHUTTER
ERROR 602
CARTRIDGE END
ERROR 608
WRONG INK IC
ERROR 627
RE-INSERT CARTRIDGE
ERROR 628
WRONG INK CARTRIDGE
ERROR 63c
INK REMAIN ZERO
ERROR 64C
NCU ERROR
ERROR 650
NCU CONECT
Cause
An excessive load was applied to the Y
motor.
Overcurrent error of X motor was
detected.
Overcurrent error of Y motor was
detected.
Take-up roller sensor error
The roller sensor cannot be correctly
read.
A media clogging occurred.
An error occurred in the position control.
Y origin could not be detected.
Abnormal linear scale.
The media width could not be correctly
read.
The media is set out of range.
Pump sensor detection error.
The control origin position of the carriage
is not set.
The control origin position of the station
is not set.
An error of the station operation was
detected.
An error of the maintenance wash shut-
ter was detected.
Ink end (unusable, only available when
cleaning with 4-color set)
Ink IC chip of the ink pack cannot be
read correctly.
There is a slot in which the ink IC chip is
not inserted for more than a certain time.
An error occurred in the information of
the ink IC chip of the ink pack.
The usage exceeds the specified value.
Cartridge remaining amount 0 (ink end /
only at 4-color ink set)
The nozzle check was interrupted due to
some problem.
The NCU unit is not connected.
Chapter5 Troubleshooting
Measures
• Turn off the power on the machine and turn it
on after a while.
If displaying again, contact your local distrib-
utor, our sales office, or service center.
• Make sure that take-up unit and take-up ten-
sion bar settings in the machine setting are
"ON".( P.3-14)
• Check the set condition of the media.
• Confirm that the take-up unit operates using
the manual SW.
• Remove the media and reset it.
• Turn off the power on the machine and turn it
on after a while.
If displaying again, contact your local distrib-
utor, our sales office, or service center.
• Check the media set position.(
• Clean the media sensor.(
• Turn off the power on the machine and turn it
on after a while.
• Check the media set position.(
• Turn off the power on the machine and turn it
on after a while.
If displaying again, contact your local distrib-
utor, our sales office, or service center.
• Contact your local distributor, our sales
office, or service center.
• Turn off the power on the machine and turn it
on after a while.
If displaying again, contact your local distrib-
utor, our sales office, or service center.
• Replace with new ink.
• Make sure that the ink IC chip is correctly
inserted.
• Reinsert the ink IC chip.
• Turn off the power on the machine and turn it
on after a while.
If displaying again, contact your local distrib-
utor, our sales office, or service center.
• Set an ink IC chip.
• Check that the nozzle is not clogged.
• Replace with new ink.
• Turn off the power on the machine and turn it
on after a while.
If displaying again, contact your local distrib-
utor, our sales office, or service center.
1
P.2-4)
P.4-3)
2
P.2-4)
2
2
5
6
5-13