Kubota L2800 Workshop Manual page 93

L2800, L3400, WSM
ENGINE BODY (Continued)
Timing Gear
Crank Gear to Idle Gear
Idle Gear to Cam Gear
Idle Gear to Injection Pump Gear
Crank Gear to Oil Pump Gear
Idle Gear
Idle Gear Shaft to Idle Gear Bushing
Idle Gear Shaft
Idle Gear Bushing
Camshaft
Camshaft
Cam
Camshaft Journal to Cylinder Block Bore
Camshaft Journal
Cylinder Block Bore
Piston Pin Bore
Second Ring to Ring Groove
[D1403-M]
[D1703-M]
Oil Ring to Ring Groove
Top Ring
[D1403-M]
[D1703-M]
Tractor Manuals Scotland
Item
Backlash
Backlash
Backlash
Backlash
Side Clearance
Clearance
O.D.
I.D.
Side Clearance
Alignment
Height
(Intake / Exhaust)
Clearance
O.D.
I.D.
I.D.
Clearance
Clearance
Clearance
Ring Gap
Ring Gap
Tractor Manuals Scotland - Please Do Not Copy
1-S6
Factory Specification
0.0415 to 0.1122 mm
0.00163 to 0.00442 in.
0.0415 to 0.1154 mm
0.00163 to 0.00454 in.
0.0415 to 0.1154 mm
0.00163 to 0.00454 in.
0.0415 to 0.1090 mm
0.00163 to 0.00201 in.
0.12 to 0.48 mm
0.0047 to 0.0189 in.
0.025 to 0.066 mm
0.00098 to 0.00260 in.
37.959 to 37.975 mm
1.49445 to 1.49508 in.
38.000 to 38.025 mm
1.49606 to 1.49704 in.
0.07 to 0.22 mm
0.0028 to 0.0087 in.
–
33.90 mm
1.3346 in.
0.050 to 0.091 mm
0.00197 to 0.00358 in.
39.934 to 39.950 mm
1.57221 to 1.57284 in.
40.000 to 40.025 mm
1.57480 to 1.57579 in.
25.000 to 25.013 mm
0.98425 to 0.98476 in.
0.093 to 0.128 mm
0.0037 to 0.0050 in.
0.093 to 0.128 mm
0.0037 to 0.0050 in.
0.020 to 0.060 mm
0.0008 to 0.0021 in.
0.20 to 0.35 mm
0.0079 to 0.0138 in.
0.20 to 0.40 mm
0.0079 to 0.0157 in.
ENGINE
Allowable Limit
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.9 mm
0.0354 in.
0.1 mm
0.0039 in.
–
–
0.3 mm
0.0118 in.
0.01 mm
0.0004 in.
33.85 mm
1.3327 in.
0.15 mm
0.0059 in.
–
–
25.05 mm
0.9862 in.
0.2 mm
0.0079 in.
0.2 mm
0.0079 in.
0.15 mm
0.0059 in.
1.25 mm
0.0492 in.
1.25 mm
0.0492 in.
W1013874
KiSC issued 08, 2007 A