L2501, WSM INFORMATION 1. SAFETY FIRST SAFETY FIRST • This symbol, the industry's "Safety Alert Symbol", is used throughout this manual and on labels on the machine itself to warn of the possibility of personal injury. Read these instructions carefully. •...
Page 6
L2501, WSM INFORMATION OPERATE SAFELY • Do not use the machine after you consume alcohol or medication or when you are tired. • Put on applicable clothing and safety equipment. • Use applicable tools only. Do not use alternative tools or parts. •...
Page 7
L2501, WSM INFORMATION KEEP A GOOD AIRFLOW IN THE WORK AREA • If the engine is in operation, make sure that the area has good airflow. Do not operate the engine in a closed area. The exhaust gas contains poisonous carbon monoxide.
L2501, WSM INFORMATION 2. SAFETY DECALS The following safety decals are installed on the machine. If a decal becomes damaged, illegible or is not on the machine, replace it. The decal part number is listed in the parts list. WSM000001INI0013US0 9Y1211121INI0001US0 KiSC issued 09, 2014 A...
Page 10
L2501, WSM INFORMATION 9Y1211121INI0003US0 CARE OF DANGER, WARNING AND CAUTION LABELS 1. Keep danger, warning and caution labels clean and free from obstructing material. 2. Clean danger, warning and caution labels with soap and water, dry with a soft cloth. 3.
L2501, WSM INFORMATION 4. TRAVELING SPEEDS Manual Transmission Type (At rated engine rpm) Model L2501 Tire size (Rear) 11.2-24 Shuttle shift Range gear Main gear shift km/h lever shift lever lever Forward High 10.0 17.3 10.7 Reverse Reverse The company reserves the right to change the specifications without notice. ...
Page 15
GENERAL CONTENTS 1. TRACTOR IDENTIFICATION....................... G-1 [1] MODEL NAME AND SERIAL NUMBERS ................G-1 [2] E4B ENGINE .......................... G-2 [3] CYLINDER NUMBER ......................G-2 2. GENERAL PRECAUTIONS......................G-3 3. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING ........G-4 [1] WIRING ..........................G-4 [2] BATTERY ..........................
L2501, WSM GENERAL 1. TRACTOR IDENTIFICATION [1] MODEL NAME AND SERIAL NUMBERS When contacting your local KUBOTA distributor, always specify engine serial number, tractor serial number and hour meter reading. (1) Tractor Identification Plate (4) ROPS Identification Plate (2) Tractor Serial Number...
Nonroad Emission Standards continue to change. The timing or applicable date of the specific Nonroad Emission regulations depends on the engine output classification. Over the past several years, KUBOTA has been supplying diesel engines that comply with regulations in the respective countries affected by Nonroad Emission regulations. For KUBOTA Engines, E4B will be the designation that identifies engine models affected by the next emission phase (See the table below).
• When it is necessary to use special tools, use KUBOTA special tools. Refer to the drawings when you make special tools that you do not use frequently.
L2501, WSM GENERAL 3. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING To ensure safety and prevent damage to the machine and surrounding equipment, obey the following precautions in handling electrical parts and wiring. IMPORTANT • Check electrical wiring for damage and loosened connection every year.
Page 20
L2501, WSM GENERAL • Repair or change torn or aged wiring immediately. (1) Aged (3) Insulating Vinyl Tape (2) Torn WSM000001GEG0065US0 • Securely insert grommet. (1) Grommet (A) Correct (B) Incorrect WSM000001GEG0066US0 • Securely clamp, being careful not to damage wiring. (1) Clamp (3) Clamp (Wind Clamp Spirally)
L2501, WSM GENERAL [2] BATTERY • Be careful not to confuse positive and negative terminal posts. • When you remove battery cables, disconnect negative cable first. When you install battery cables, check for polarity and connect positive cable first. • Do not install any battery with capacity other than is specified (Ah).
L2501, WSM GENERAL • Use sandpaper to remove rust from terminals. • Repair deformed terminal. Make sure that there is no terminal being exposed or displaced. (1) Exposed Terminal (3) Sandpaper (2) Deformed Terminal (4) Rust WSM000001GEG0075US0 • Make sure that there is no female connector being too open. (A) Correct (B) Incorrect WSM000001GEG0076US0...
L2501, WSM GENERAL [6] COLOR OF WIRING • Colors of wire are specified to the color codes. • This symbol of "/" shows color with stripe(s). (An example) Red stripe on white color: W/R Color of wiring Color code Black Brown Green Gray...
(GC-LB) Pedal shaft Battery terminal Lift rod Tie-rod end (4WD) NOTE • The product name of KUBOTA genuine UDT fluid may be different from that in the Operator's Manual depending on countries or territories. 9Y1211121GEG0004US0 KiSC issued 09, 2014 A...
Page 25
• No.2-D is a distillate fuel of lower volatility for engines in industrial and heavy mobile service. (SAE J313 JUN87) Transmission Oil • KUBOTA Super UDT-2: For an enhanced ownership experience, we highly recommend Super UDT-2 to be used instead of standard hydraulic/transmission fluid. Super UDT-2 is a proprietary KUBOTA formulation that deliveries superior performance and protection in all operating conditions.
L2501, WSM GENERAL 5. TIGHTENING TORQUES [1] GENERAL USE SCREWS, BOLTS AND NUTS Tighten screws, bolts and nuts whose tightening torques are not specified in this Workshop Manual according to the table below. Indication on top of bolt No-grade or 4T Indication on top of nut No-grade or 4T Material of opponent part...
L2501, WSM GENERAL [3] METRIC SCREWS, BOLTS AND NUTS Grade Property class 8.8 Property class 10.9 Unit N·m kgf·m lbf·ft N·m kgf·m lbf·ft 24 to 27 2.4 to 2.8 18 to 20 30 to 34 3.0 to 3.5 22 to 25 48 to 55 4.9 to 5.7 36 to 41...
L2501, WSM GENERAL 6. MAINTENANCE CHECK LIST Service Interval Refer- After Item ence since 50 100 150 200 250 300 350 400 450 500 550 600 650 700 page every ...
Page 29
*4 When the battery is used for less than 100 hours per year, check the battery condition by reading the indicator annually. • The items listed above (@ marked) are registered as emission related critical parts by KUBOTA in the U.S.EPA nonroad emission regulation. As the engine owner, you are responsible for the performance of the required maintenance on the engine according to the above instruction.
L2501, WSM GENERAL 7. CHECK AND MAINTENANCE WARNING To avoid personal injury or death: • Be sure to check and service the tractor on a level surface with the engine shut off and the parking brake "ON" and implement lowered to the ground. 9Y1211121GEG0008US0 [1] DAILY CHECK To prevent trouble from occurring, it is important to know the condition of the tractor.