KTM 1190 RC8 R EU/UK 2009 Repair Manual page 7

CONTENTS
Reinstalling the throttle valve body when the
adjustments have been made........................................ 222
Throttle position sensor circuit B................................... 223
Manifold absolute pressure sensor................................. 223
Connecting the vacuum hand pump to the manifold
absolute pressure sensor .............................................. 224
Ambient air pressure sensor.......................................... 225
Injector ...................................................................... 225
Rollover sensor............................................................ 226
EFI control unit ........................................................... 227
Requesting the EFI control unit activation code.............. 227
Coding the EFI control unit........................................... 227
Flashing the EFI control unit ........................................ 228
IMMOBILIZER BLINK CODE............................................. 229
ENGINE CONTROL TROUBLE CODE ................................. 238
CONNECTOR OVERVIEW.................................................. 391
Motor drive circuit A connector AE ................................ 391
Connector AI ............................................................... 391
Crankshaft position sensor connector AL........................ 391
Clutch switch, connector AL ......................................... 391
Throttle position sensor circuit A, connector AM ............. 391
Throttle position sensor circuit B, connector AM............. 392
Gear position sensor, connector AM............................... 392
Fuel pump connector AM ............................................. 392
Wheel speed sensor, connector AM ............................... 392
Connector AO.............................................................. 392
Diagnostic connection plug AP...................................... 393
Rollover sensor connector AP........................................ 393
Throttle position sensor circuit A, connector AR.............. 393
Throttle position sensor circuit B, connector AR ............. 394
Fuel pump connector AR.............................................. 394
Side stand switch, connector AR................................... 394
Ignition coil cylinder 1 connector AS ............................. 394
Ignition coil cylinder 2 connector AS ............................. 394
CAN bus terminating resistor connector AT .................... 395
Crankshaft position sensor, connector AT....................... 395
Clutch switch connector AT .......................................... 395
Engine coolant temperature sensor cylinder 1 connector
AX.............................................................................. 395
Throttle stepper motor circuit B, connector CA ............... 395
Lambda sensor cylinder 1, connector CA ....................... 396
Lambda sensor cylinder 2, connector CA ....................... 396
Lambda sensor cylinder 1, connector CE ....................... 396
Lambda sensor cylinder 2, connector CE ....................... 396
Secondary air valve connector CK.................................. 396
Connector CM ............................................................. 397
Connector CO.............................................................. 397
Connector CP .............................................................. 398
Connector CQ.............................................................. 398
Connector CU.............................................................. 398
Fuel evaporation valve connector DF.............................. 399
Secondary air valve connector DF.................................. 399
Electric starter lock control unit, connector DN .............. 399
Immobilizer control unit, connector DN ......................... 399
Electric starter lock control unit, connector DO............... 399
Immobilizer control unit, connector DO.......................... 400
Ambient air pressure sensor connector DP ..................... 400
Manifold absolute pressure sensor cylinder 1,
connector DP .............................................................. 400
Manifold absolute pressure sensor cylinder 2
connector DP .............................................................. 400
Injector cylinder 1 connector DQ................................... 400
Injector cylinder 2 connector DQ................................... 401
ICU antenna connector DV ........................................... 401
Fuel pump relay connector EB ...................................... 401
ICU antenna connector EL............................................ 401
Connector EQ.............................................................. 401
Connector ER.............................................................. 402
Connector ES .............................................................. 402
Connector ET .............................................................. 402
Combination instrument connector EV ........................... 403
Exhaust air injection valve, connector FE ....................... 403
Fuel pump relay .......................................................... 404
CAN bus terminating resistor ........................................ 404
TECHNICAL DATA - ENGINE ............................................ 405
Capacity - engine oil .................................................... 405
Capacity - coolant........................................................ 406
TECHNICAL DATA - TOLERANCE, WEAR LIMITS OF
ENGINE ......................................................................... 407
TECHNICAL DATA - ENGINE TIGHTENING TORQUES........ 409
TECHNICAL DATA - CHASSIS .......................................... 411
Lighting equipment ..................................................... 411
Capacity - fuel............................................................. 412
TECHNICAL DATA - FORK................................................ 413
TECHNICAL DATA - SHOCK ABSORBER ........................... 414
TECHNICAL DATA - CHASSIS TIGHTENING TORQUES ...... 415
CLEANING/CONSERVATION............................................. 417
Cleaning motorcycle .................................................... 417
Conservation for winter operation .................................. 417
STORAGE ....................................................................... 419
Storage....................................................................... 419
Putting into operation after storage ............................... 419
SERVICE SCHEDULE....................................................... 420
Important service tasks to be carried out by an
authorized KTM-RC8 workshop. .................................... 420
Important service tasks to be carried out by an
authorized KTM-RC8 workshop. (as additional job) ......... 421
WIRING DIAGRAM .......................................................... 422
1 of 3......................................................................... 422
2 of 3......................................................................... 426
3 of 3......................................................................... 432
OPERATING SUBSTANCES .............................................. 436
AUXILIARY SUBSTANCES................................................ 438
SPECIAL TOOLS.............................................................. 440
STANDARDS................................................................... 452
INDEX ............................................................................ 453
5