Page 1 2015 OWNER'S MANUAL 1190 RC8 R US Art. no. 3213285en...
Page 3 KTM accepts no liability for delivery options, devi- ations from illustrations and descriptions, misprints, and other errors.
Page 4 DEAR KTM CUSTOMER ISO 9001(12 100 6061) According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to the maximum possible quality of the products. Issued by: TÜV Management Service KTM Sportmotorcycle GmbH 5230 Mattighofen, Austria...
Page 5: Table Of Contents
TABLE OF CONTENTS SERIAL NUMBERS ............28 TABLE OF CONTENTS MEANS OF REPRESENTATION ........8 Vehicle identification number/type label....28 Symbols used ............8 Key number............28 Formats used............8 Engine number ..........29 SAFETY ADVICE.............. 9 Fork part number ..........29 Use definition - intended use ........
Page 6 TABLE OF CONTENTS 6.13.9 notes/warnings..........44 6.13.35 UNITS menu ..........77 6.13.10 Overview of ROAD mode ......... 48 6.13.36 Kilometers/miles menu, SET KM/MILES... 78 6.13.11 Distance menu 1, ODO/Trip 1/Time 1/Avs 1 ..49 6.13.37 Temperature display menu, SET °C/°F ..... 79 6.13.12 Distance menu 2, ODO/Trip 2/Time 2/Avs 2 ..
Page 7 TABLE OF CONTENTS 6.13.57 Setting the unit of fuel consumption (liters) SERVICE SCHEDULE ..........129 SET FUEL CONS ......... 104 Service schedule..........129 6.13.58 Unit of fuel consumption (gallons) 10 TUNING THE CHASSIS ..........132 SET GAL US/UK .......... 105 10.1 Fork/shock absorber .........
Page 8 TABLE OF CONTENTS 10.23 Adjusting the handlebar height/position ..... 156 12.2 Checking the front brake discs ......181 10.24 Subframe position..........161 12.3 Checking the rear brake disc ......182 10.25 Adjusting the subframe position ......162 12.4 Checking the front brake fluid level ....183 11 SERVICE WORK ON THE CHASSIS.......
Page 9 TABLE OF CONTENTS 15 COOLING SYSTEM ............223 23.3 Capacities ............258 15.1 Cooling system ..........223 23.3.1 Engine oil ........... 258 15.2 Checking the coolant level ........ 223 23.3.2 Coolant ............259 15.3 Filling cooling system compensating tank... 224 23.3.3 Fuel ............
Page 10: Means Of Representation
All work marked with this symbol requires specialist knowledge and technical understanding. In the interest of your own safety, have these jobs performed by an authorized KTM workshop. There, your motorcycle will be optimally cared for by specially trained experts using the specialist tools required.
Page 11: Safety Advice
SAFETY ADVICE Use definition - intended use KTM sport motorcycles are designed and constructed to meet the normal demands of regular road operation and also for use on race courses, but not for offroad use. Info The motorcycle is only authorized for operation on public roads in the homologated version.
Page 12: Degrees Of Risk And Symbols
SAFETY ADVICE Degrees of risk and symbols Danger Indicates a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures are not taken. Warning Indicates a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken. Caution Indicates a danger that may lead to minor injuries if the appropriate measures are not taken.
Page 14: Overview Of Labels
SAFETY ADVICE Overview of labels B01298-10...
Page 15 SAFETY ADVICE Information on putting into operation Type label for Canada Type label for the USA Emission control information Noise emission information Chain tension information Information on suspension setting Information on locking of passenger seat Information on fuel quality/engine electronics mapping Information on putting into operation 600961-01...
Page 16 SAFETY ADVICE M00734-01 Type label for Canada M00735-01 Type label for the USA...
Page 17 SAFETY ADVICE Emission control information M00736-01 M00737-01 Noise emission information...
Page 18 SAFETY ADVICE M00738-01 Chain tension information Information on suspension setting M00739-01...
Page 19: Reporting Safety Defects
If you believe that your vehicle has a defect which could cause an accident resulting in injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying KTM North America, Inc. If NHTSA receives multiple similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 20: Noise Emission Warranty
Noise emission warranty KTM Sportmotorcycle AG warrants that this exhaust system, at the time of sale, meets all applicable U.S. EPA Federal noise standards. This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all subsequent buyers.
Page 21: Tampering Warning
SAFETY ADVICE Tampering warning Tampering with the noise control system is prohibited. Federal law prohibits the following acts or the causing thereof: 1 The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate pur- chaser or while it is in use, or 2 the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
Page 22: Protective Clothing
Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always wear protective clothing that is in good condition and meets the legal requirements. In the interest of your own safety, KTM recommends that you only operate the vehicle while wearing protective clothing. 2.12 Work rules Special tools are necessary for certain tasks.
Page 23: Environment
Keep the Owner's Manual in an accessible place to enable you to refer to it as needed. If you would like to know more about the vehicle or have questions on the material you read, please contact an authorized KTM dealer.
Page 24: Important Notes
Guarantee, warranty The work prescribed in the service schedule must be carried out by an authorized KTM workshop only and confirmed in the customer's Service & Warranty Booklet and in the KTM Dealer.net; otherwise, all warranty claims will be void. No warranty claims can be considered for damage resulting from manipulations and/or alterations to the vehicle.
Page 25: Figures
Please follow the instructions in the text. Customer service Your authorized KTM dealer will be happy to answer any questions you may have on your vehicle and KTM. A list of authorized KTM dealers can be found on the KTM website.
Page 26: View Of Vehicle
VIEW OF VEHICLE View of vehicle, front left (example) B01301-10...
Page 27 VIEW OF VEHICLE Clutch lever ( p. 31) Light switch ( p. 33) Headlight flasher switch ( p. 33) Turn signal switch ( p. 34) Horn button ( p. 32) Filler cap Tool set ( p. 110) Seat lock ( p.
Page 28: View Of Vehicle, Rear Right (Example)
VIEW OF VEHICLE View of vehicle, rear right (example) B01302-10...
Page 29 VIEW OF VEHICLE Passenger seat Supporting strap ( p. 110) Fork rebound adjustment Indicator lamps ( p. 42) Ignition/steering lock ( p. 35) Emergency OFF switch ( p. 34) Electric starter button ( p. 35) Hand brake lever ( p. 31) Vehicle identification number/type label ( p.
Page 30: Serial Numbers
SERIAL NUMBERS Vehicle identification number/type label  The vehicle identification number is stamped on the frame behind the steering head on the right.  The type label USA is on the frame above the vehicle identification number. The type label for Canada is located on the frame on the left behind the steering head. 402400-10 Key number ...
Page 31: Engine Number
SERIAL NUMBERS Engine number  The engine number is stamped on the right side of the engine. 402296-10 Fork part number  The fork part number is stamped on the inner side of the fork stub. 402295-10...
Page 32: Shock Absorber Article Number
SERIAL NUMBERS Shock absorber article number  The shock absorber part number is stamped on the top of the shock absorber above the adjusting ring towards the rear. 402298-10 Steering damper part number  The steering damper part number is stamped on the top of the steering damper. 402401-10...
Page 33: Controls
CONTROLS Clutch lever  The clutch lever is fitted on the left side of the handlebar. The clutch is hydraulic and self-adjusting. 100659-10 Hand brake lever  The hand brake lever is fitted on the right side of the handlebar. The hand brake lever operates the front brake.
Page 34: Throttle Grip
CONTROLS Throttle grip  The throttle grip is fitted on the right side of the handlebar. B00568-10 Horn button  The horn button is fitted on the left side of the handlebar. Possible states • Horn button in neutral position pressed –...
Page 35: Light Switch
CONTROLS Light switch  The light switch is fitted on the left side of the handlebar. Possible states Low beam on – The light switch is turned downward. In this position, the low beam and tail light are switched on. High beam on –...
Page 36: Turn Signal Switch
CONTROLS Turn signal switch  The turn signal switch is fitted on the left side of the handlebar. Possible states Turn signal off Left turn signal on – The turn signal switch is pressed to the left. The turn signal switch automatically returns to the central position after use. Right turn signal on –...
Page 37: Electric Starter Button
CONTROLS Electric starter button  The electric starter button is fitted on the right side of the handlebar. Possible states • Electric starter button in neutral position pressed – In this position, the electric starter is operated. • Electric starter button 100664-11 6.10 Ignition/steering lock...
Page 38: Locking The Steering
CONTROLS 6.11 Locking the steering Note Danger of damage The parked vehicle may roll away or fall over. – Always place the vehicle on a firm and even surface. – Park the vehicle. – Turn the handlebar all the way to the left. –...
Page 39: Combination Instrument
CONTROLS 6.13 Combination instrument 6.13.1 Overview Display ( p. 40) Function buttons ( p. 41) Indicator lamps ( p. 42) Info display ( p. 43) 401121-10...
Page 40: Function Buttons, Handlebar
CONTROLS 6.13.2 function buttons, handlebar  The MODE button is fitted on the handlebar, front left.  The LAP button is fitted on the handlebar, rear left. MODE button Changes to the next item on the info display in ROAD mode and in RACE mode. LAP button Changes to the next item on the info display in ROAD mode.
Page 41: Activation And Test
The speed display counts from 0 to 300 and back. The remaining display segments outside the info display light up briefly. The KTM logo appears in the info display. The display then changes to the last selected mode. 401120-01...
Page 42: Display
CONTROLS 6.13.4 Display  The tachometer displays the engine speed in revolutions per minute (RPM).  The red marking marks the over-rev (excessive speed) range of the engine.  The gear display shows the engaged gear. Info The engaged gear can also be displayed in the info display. The speed ...
Page 43: Function Buttons
CONTROLS 6.13.5 Function buttons  The button controls different functions.  The button controls different functions.  The button "MODE" switches between display modes or opens one of the setup menus. 400430-11...
Page 44: Indicator Lamps
CONTROLS 6.13.6 Indicator lamps Possible states The turn signal indicator lamp flashes green simultaneously with the turn signal – The turn signal is switched on. The oil pressure warning lamp lights up red – The oil pressure is too low. The shift warning lights up/flashes red –...
Page 45: Info Display
CONTROLS 6.13.7 Info display  The info display has two menus. Menu 1 is ROAD mode (standard) for riding on public roads. Menu 2 is the RACE mode for riding on race tracks. It allows riders to time laps themselves. If the general warning lamp lights up, the corresponding message is shown periodically in the info display.
Page 46: Immobilizer
The second black ignition key is activated when the vehicle is shipped. Two additional spare ignition keys (key number on the KEYCODECARD) can be ordered from an authorized KTM workshop, but they must be activated before use. 6.13.9 notes/warnings LOW FUEL appears on the info display if the minimum range falls below the specified value.
Page 47 CONTROLS LOW BATTERY appears on the info display if the battery voltage falls below the specified value. Battery voltage 10.80 V 401124-01 SERVICE IN xxx KM(MPH) appears on the info display if the distance to the next service falls below the specified value. Distance 500 km (310 mi) 401125-01...
Page 48 CONTROLS ICE appears on the info display if the external temperature falls below the specified value. Temperature 3 °C (37 °F) ICE disappears if the external temperature rises above the specified value. Temperature 4 °C (39 °F) 401127-01...
Page 50: Overview Of Road Mode
CONTROLS 6.13.10 Overview of ROAD mode 401128-10...
Page 51: Distance Menu 1, Odo/Trip 1/Time 1/Avs 1
CONTROLS Functions in ROAD mode Distance menu 1, ODO/Trip 1/Time 1/Avs 1 Distance menu 2, ODO/Trip 2/Time 2/Avs 2 Gear display menu, ODO/Trip 1/Gear Fuel and external temperature menu, FUEL Mapping menu, ENGINE MAP Next service menu, DISTANCE TO Next Service 6.13.11 Distance menu 1, ODO/Trip 1/Time 1/Avs 1 Condition Alternative 1...
Page 52: Distance Menu 2, Odo/Trip 2/Time 2/Avs 2
CONTROLS Press the button No function Press the button No function Press the button The display changes to the SET‑UP menu and the button 3 - 5 seconds. Press the MODE but- The display of Trip 1, Time 1 and Avs 1 is reset ton for 3 - 5 sec- onds.
Page 53: Gear Display Menu, Odo/Trip 1/Gear
CONTROLS The calculation of this value starts with the first speed signal and ends 3 seconds after the last speed signal. Avs 2 shows the average speed and is coupled with Trip 2 and Time 2. Press the button No function Press the button No function Press the button...
Page 54 CONTROLS Trip 1 shows the distance covered since the last reset. For example, between two refueling stops. Trip 1 is always running and counts up to 9999.9. Gear shows the gear currently engaged. Press the button No function Press the button No function Press the button The display changes to the SET‑UP menu...
Page 55: Fuel And External Temperature Menu, Fuel
CONTROLS 6.13.14 Fuel and external temperature menu, FUEL Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. • The motorcycle is being ridden. • ROAD mode –...
Page 56: Mapping Menu, Engine Map
CONTROLS Press the MODE but- Next display mode ton briefly. 6.13.15 Mapping menu, ENGINE MAP Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. • The motorcycle is being ridden. •...
Page 57: Next Service Menu, Distance To Next Service
CONTROLS 6.13.16 Next service menu, DISTANCE TO Next Service Condition • The ignition is on. • The motorcycle is stationary. ROAD mode • – Press the MODE button briefly and repeatedly until DISTANCE TONext Service appears in the info display. DISTANCE TO Next Service shows the distance before the next service is necessary.
Page 58: Overview Of Race Mode
CONTROLS 6.13.17 Overview of RACE mode 401142-10...
Page 59: Remaining Laps Menu, Lapstogo
CONTROLS Functions in RACE mode Remaining laps menu, LAPSTOGO Maximum lap speed menu, TOPSPEED Gear display menu, LastLap/RaceTrip/Gear Fuel and external temperature menu, FUEL Mapping menu, ENGINE MAP Lap times menu, LAP/BESTLAP/LapTime Maximum speed menu, LAP/BESTLAP/TopSpeed Total distance menu in Race mode RACEODO 6.13.18 Remaining laps menu, LAPSTOGO Condition Alternative 1...
Page 60: Maximum Lap Speed Menu, Topspeed
CONTROLS LastLap shows the lap time of the last lap. ±Last shows the difference between the last lap and the lap before last. ±Best shows the difference between the last lap and the best lap. If the last lap was the fastest, you see behind ±Best: the Best! symbol in the info display. Press the button No function Press the button...
Page 61 CONTROLS If an R appears after TOPSPEED, the stopwatch is running in the background. If a P appears after TOPSPEED, the stopwatch in the background is active but waiting for a speed signal. The time is not running. This function is controlled with the LAP button. LastLap shows the maximum speed of the last lap.
Page 62: Gear Display Menu, Lastlap/Racetrip/Gear
CONTROLS 6.13.20 Gear display menu, LastLap/RaceTrip/Gear Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • RACE mode Alternative 2 • The ignition is on. • The motorcycle is being ridden. • RACE mode 401145-01 – Press the MODE button briefly and repeatedly until LastLap, RaceTrip, and Gear appear in the info display.
Page 63: Fuel And External Temperature Menu, Fuel
CONTROLS 6.13.21 Fuel and external temperature menu, FUEL Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • RACE mode Alternative 2 • The ignition is on. • The motorcycle is being ridden. • RACE mode –...
Page 64: Mapping Menu, Engine Map
CONTROLS Press the MODE but- Next display mode ton briefly. 6.13.22 Mapping menu, ENGINE MAP Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • RACE mode Alternative 2 • The ignition is on. • The motorcycle is being ridden. •...
Page 65: Lap Times Menu, Lap/Bestlap/Laptime
CONTROLS 6.13.23 Lap times menu, LAP/BESTLAP/LapTime Condition • The ignition is on. • The motorcycle is stationary. RACE mode • – Press the MODE button briefly and repeatedly until LAP/BESTLAP/LapTime appears in the info display. LAP shows the selected lap. BESTLAP shows the number of the lap with the best lap time.
Page 66: Maximum Speed Menu, Lap/Bestlap/Topspeed
CONTROLS 6.13.24 Maximum speed menu, LAP/BESTLAP/TopSpeed Condition • The ignition is on. • The motorcycle is stationary. RACE mode • – Press the MODE button briefly and repeatedly until LAP/BESTLAP/TopSpeed appears in the info display. LAP shows the selected lap. BESTLAP shows the lap in which the highest maximum speed was reached.
Page 67: Total Distance In Race Mode Menu, Raceodo
CONTROLS 6.13.25 Total distance in Race mode menu, RACEODO Condition • The ignition is on. • The motorcycle is stationary. RACE mode • – Press the MODE button briefly and repeatedly until RACEODO appears at the top of the info display. RACEODO shows the total distance covered in RACE mode.
Page 68: Overview Of Set-Up Mode
CONTROLS 6.13.26 Overview of SET‑UP mode ODO/Trip 1 ODO/Trip 2 ODO/Trip 1/Gear FUEL ENGINE MAP SHIFT RPMS DISTANCE TO Next Service LAP BLANK TIME CHANGE MODE SET NUM LAPS SET CLOCK LAPSTOGO TRIP F RESET SETTINGS... TOPSPEED ** SET-UP ** BACK...
Page 69 CONTROLS Settings in SET‑UP mode Mode menu, CHANGE MODE Time menu, SET CLOCK Settings menu, SETTINGS Units menu, UNITS Additional functions menu, OPTIONS EXIT SETUP menu...
Page 70: Set-Up Menu
CONTROLS 6.13.27 SET‑UP menu Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. • The motorcycle is stationary. • RACE mode – Press the button and the button for 3 - 5 seconds.
Page 71: Mode Menu, Change Mode
CONTROLS Press the MODE but- The menu in front of the arrow is selected ton for 3 - 5 sec- onds. Press the MODE but- The menu in front of the arrow is selected ton briefly. 6.13.28 Mode menu, CHANGE MODE Condition Alternative 1 •...
Page 72: Time Menu, Set Clock
CONTROLS Press the MODE but- Open and exit CHANGE MODE ton briefly. 6.13.29 Time menu, SET CLOCK Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. •...
Page 73: Settings Menu
CONTROLS 6.13.30 SETTINGS menu Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. • The motorcycle is stationary. • RACE mode – Press the button and the button for 3 - 5 seconds.
Page 74: Shift Warning Lamp Menu, Shift Rpms
CONTROLS Press the MODE but- The menu in front of the arrow is selected ton for 3 - 5 sec- onds. Press the MODE but- The menu in front of the arrow is selected ton briefly. 6.13.31 Shift warning lamp menu, SHIFT RPMS Condition Alternative 1 •...
Page 75: Lap Button Blank Time, Lap Blank Time Menu
CONTROLS Press the MODE but- Open and exit SHIFT RPMS or change to the next value ton for 3 - 5 sec- onds. Press the MODE but- Open and exit SHIFT RPMS or change to the next value ton briefly. 6.13.32 LAP button blank time, LAP BLANK TIME menu Condition Alternative 1...
Page 76: Number Of Laps Menu, Set Num Laps
CONTROLS Press the MODE but- Open and exit LAP BLANK TIME ton for 3 - 5 sec- onds. Press the MODE but- Open and exit LAP BLANK TIME ton briefly. 6.13.33 Number of laps menu, SET NUM LAPS Condition Alternative 1 •...
Page 77: Fuel Reserve Display Menu, Trip F Reset
CONTROLS Press the MODE but- Open and exit SET NUM LAPS ton for 3 - 5 sec- onds. Press the MODE but- Open and exit SET NUM LAPS ton briefly. 6.13.34 Fuel reserve display menu, TRIP F RESET Condition Alternative 1 •...
Page 78 CONTROLS Press the button No function and the button 3 - 5 seconds. Press the MODE but- Open and exit TRIP F RESET ton for 3 - 5 sec- onds. Press the MODE but- Open and exit TRIP F RESET ton briefly.
Page 79: Units Menu
CONTROLS 6.13.35 UNITS menu Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. • The motorcycle is stationary. • RACE mode – Press the button and the button for 3 - 5 seconds.
Page 80: Kilometers/Miles Menu, Set Km/Miles
CONTROLS Press the MODE but- The menu in front of the arrow is selected ton briefly. 6.13.36 Kilometers/miles menu, SET KM/MILES Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on.
Page 81: Temperature Display Menu, Set °C/°F
CONTROLS Press the MODE but- Open and exit SET KM/MILES ton briefly. 6.13.37 Temperature display menu, SET °C/°F Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. •...
Page 82: Fuel Consumption Menu (Liters), Set Fuel Cons
CONTROLS Press the MODE but- Open and exit SET °C/°F ton briefly. 6.13.38 Fuel consumption menu (liters), SET FUEL CONS Condition • The ignition is on. • The motorcycle is stationary. • The KM/H unit is activated. – Press the button and the button for 3 - 5 seconds.
Page 83: Fuel Consumption Menu (Gallons), Set Gal Us/Uk
CONTROLS 6.13.39 Fuel consumption menu (gallons), SET GAL US/UK Condition • The ignition is on. • The motorcycle is stationary. The MPH unit is activated. • – Press the button and the button for 3 - 5 seconds. – Press the button three times until the symbol shows UNITS in the info display.
Page 84: Additional Functions Menu, Options
CONTROLS 6.13.40 Additional functions menu, OPTIONS Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. • The motorcycle is stationary. • RACE mode 401158-01 – Press the button and the button for 3 - 5 seconds.
Page 85: Quick Shifter Menu, Option Qkshift
CONTROLS Press the MODE but- The menu in front of the arrow is selected ton briefly. 6.13.41 Quick shifter menu, OPTION QKSHIFT Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 •...
Page 86: External Temperature Display Menu, Option Outtemp
CONTROLS Press the MODE but- Open and exit OPTION QKSHIFT ton briefly. 6.13.42 External temperature display menu, OPTION OUTTEMP Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. •...
Page 87: Tire Pressure Monitor Menu, Option Tpms
CONTROLS Press the MODE but- Open and exit OPTIONOUTTEMP ton briefly. 6.13.43 Tire pressure monitor menu, OPTION TPMS Condition Alternative 1 • The ignition is on. • The motorcycle is stationary. • ROAD mode Alternative 2 • The ignition is on. •...
Page 88: Table Of Functions
CONTROLS – Press the button twice until the symbol shows OPTION TPMS in the info display. – Press the MODE button briefly. In the OPTION TPMS menu, you can switch the tire pressure check on/off (available as accessory). Press the button Switches tire pressure display on and off Press the button Switches tire pressure display on and off...
Page 89 CONTROLS Display Press the button Press the button Press the button Press the MODE but- Press the MODE but- and the button ton for 3 - 5 sec- ton briefly. 3 - 5 seconds. onds. Fuel and external tem- No function No function The display Note LOW FUEL in...
Page 90 CONTROLS Display Press the button Press the button Press the button Press the MODE but- Press the MODE but- and the button ton for 3 - 5 sec- ton briefly. 3 - 5 seconds. onds. Lap times menu, LAP/ The next lap is dis- The previous lap is The display All values in...
Page 91 CONTROLS Display Press the button Press the button Press the button Press the MODE but- Press the MODE but- and the button ton for 3 - 5 sec- ton briefly. 3 - 5 seconds. onds. LAP button blank time, Increases the value Decreases the value No function Open and exit Open and exit...
Page 92: Table Of Conditions And Menu Activation
CONTROLS Display Press the button Press the button Press the button Press the MODE but- Press the MODE but- and the button ton for 3 - 5 sec- ton briefly. 3 - 5 seconds. onds. Tire pressure monitor Switches tire pres- Switches tire pres- No function Open and exit...
Page 93 CONTROLS Display • • • • • • Menu can be activated ignition ignition ignition ignition ignition ignition is on. is on. is on. is on. is on. is on. • • • • • • motor- motor- motor- motor- motor- motor- cycle is...
Page 94 CONTROLS Display • • • • • • Menu can be activated ignition ignition ignition ignition ignition ignition is on. is on. is on. is on. is on. is on. • • • • • • motor- motor- motor- motor- motor- motor- cycle is...
Page 95 CONTROLS Display • • • • • • Menu can be activated ignition ignition ignition ignition ignition ignition is on. is on. is on. is on. is on. is on. • • • • • • motor- motor- motor- motor- motor- motor- cycle is...
Page 96: Adjusting The Mapping Of The Engine Electronics Engine Map
CONTROLS 6.13.46 Adjusting the mapping of the engine electronics ENGINE MAP Note Material damage Incorrect mapping damages the engine. – Adjust the mapping of the engine electronics for the fuel quality currently in use. Condition The ignition is on. The motorcycle is stationary. Condition ROAD mode –...
Page 97: Displaying Lap Times
CONTROLS 6.13.47 Displaying lap times Condition The ignition is on. The motorcycle is stationary. RACE mode – Press the MODE button briefly and repeatedly until LAP/BESTLAP/LapTime appears in the info display. LAP01 appears on the left of the info display. –...
Page 98: Setting Road Or Race Mode
CONTROLS – Press the MODE button briefly and repeatedly until LAP/BESTLAP/TopSpeed appears in the info display. LAP01 appears on the left of the info display. – Press the button The next lap is displayed. – Press the button The previous lap is displayed. –...
Page 99: Adjusting The Shift Speed Rpm1/2
CONTROLS The motorcycle is stationary. – Press the button and the button for 3 - 5 seconds. – Press the button once until the symbol shows SET CLOCK in the info display. – Press the MODE button briefly. The hour is shown. –...
Page 100 CONTROLS – Press the button and the button for 3 - 5 seconds. – shows SETTINGS in the info display. Press the button twice until the symbol – Press the MODE button briefly. – Press the MODE button briefly. RPM1 and RPM2 appear on the info display. The engine speed after RPM1 flashes.
Page 101: Setting The Blank Time Of The Lap Button Lap Blank Time
CONTROLS – Press the MODE button briefly. – shows EXIT SETUP in the Press the button briefly and repeatedly until the symbol info display. – Press the MODE button briefly. 6.13.52 Setting the blank time of the LAP button LAP BLANK TIME Condition The ignition is on.
Page 102: Setting The Number Of Laps Set Num Laps
CONTROLS – Press the button briefly and repeatedly until the symbol shows BACK... in the info display. – Press the MODE button briefly. – Press the button briefly and repeatedly until the symbol shows EXIT SETUP in the info display. –...
Page 103: Setting The Fuel Reserve Display Trip F Reset
CONTROLS – Press the button briefly and repeatedly until the symbol shows BACK... in the info display. – Press the MODE button briefly. – Press the button briefly and repeatedly until the symbol shows EXIT SETUP in the info display. –...
Page 104: Setting The Kilometers/Miles Set Km/Miles
CONTROLS – Press the button briefly and repeatedly until the symbol shows BACK... in the info display. – Press the MODE button briefly. – Press the button briefly and repeatedly until the symbol shows EXIT SETUP in the info display. –...
Page 105: Setting The Temperature Unit Set °C/°F
CONTROLS – Press the button and the button for 3 - 5 seconds. – shows UNITS in the info display. Press the button three times until the symbol – Press the MODE button briefly. – Press the MODE button briefly. The selected unit appears on the left in the display.
Page 106: Setting The Unit Of Fuel Consumption (Liters) Set Fuel Cons
CONTROLS – Press the button and the button for 3 - 5 seconds. – shows UNITS in the info display. Press the button three times until the symbol – Press the MODE button briefly. – Press the button once until the symbol shows SET °C/°F in the info display.
Page 107: Unit Of Fuel Consumption (Gallons) Set Gal Us/Uk
CONTROLS – Press the button and the button for 3 - 5 seconds. – shows UNITS in the info display. Press the button three times until the symbol – Press the MODE button briefly. – Press the button twice until the symbol shows SET FUEL CONS in the info display.
Page 108: Switching The External Temperature Display On/Off
CONTROLS – Press the button and the button for 3 - 5 seconds. – shows UNITS in the info display. Press the button three times until the symbol – Press the MODE button briefly. – Press the button three times until the symbol shows SET GAL US/UK in the info dis- play.
Page 109: Opening The Filler Cap
CONTROLS – Press the button and the button for 3 - 5 seconds. – shows OPTIONS in the info display. Press the button four times until the symbol – Press the MODE button briefly. – Press the button once until the symbol shows OPTION OUTTEMP in the info display.
Page 110 CONTROLS Warning Danger of poisoning Fuel is poisonous and a health hazard. – Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with soap and water.
Page 111: Closing The Filler Cap
CONTROLS 6.15 Closing the filler cap Warning Fire hazard Fuel is highly flammable, poisonous and harmful to your health. – After closing the filler cap, ensure that it is locked properly. Change cloth- ing that has been contaminated with fuel. Immediately clean contaminated areas on the skin with soap and water.
Page 112: Tool Set
CONTROLS 6.17 Tool set  The tool set is in the storage compartment under the seat. 100670-10 6.18 Supporting strap  The supporting strap is provided for the passenger to hold on to. B01308-10...
Page 113: Passenger Footrests
CONTROLS 6.19 Passenger footrests The passenger footrests can be folded up and down. Possible states Passenger footrests folded up – For operation without a passenger. • Passenger footrests folded down – For operation with a passenger. • 100672-01 6.20 Shift lever ...
Page 114: Foot Brake Lever
CONTROLS The gear positions can be seen in the picture.  The neutral or idle position is between the first and second gear. B00559-10 6.21 Foot brake lever  The foot brake lever is in front of the right footrest. The foot brake lever operates the rear brake.
Page 115: Side Stand
CONTROLS 6.22 Side stand  The side stand is located on the left side of the vehicle. The side stand is used for parking the motorcycle. Info The side stand must be folded up during motorcycle use. The side stand is coupled with the safety start system; see the riding instructions. Possible states Side stand folded out –...
Page 116: Preparing For Use
The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle. Warning Danger of accidents Uncontrollable handling characteristic due to non-approved and/or non-recommended tires/wheels. – Only tires/wheels approved by KTM and with the corresponding speed index should be used. Warning Danger of accidents Reduced road grip with new tires. –...
Page 117: Running The Engine In
PREPARING FOR USE – Make sure that the pre-delivery inspection work has been carried out exclusively by an authorized KTM workshop. You receive a delivery certificate and the Service and Warranty Booklet at vehicle handover. – Before your first trip, read the entire operating instructions carefully.
Page 118: Loading The Vehicle
PREPARING FOR USE Loading the vehicle Warning Danger of accidents Unstable handling characteristics. – Do not exceed the maximum permitted weight and axle loads. The overall weight consists of: motorcycle operational and with a full tank, driver and passenger with protective clothing and helmet, baggage. Warning Danger of accidents Unstable handling characteristics due to incorrect mounting of suitcase and/or tank rucksack.
Page 119 PREPARING FOR USE Warning Danger of accidents Unstable handling characteristics due to slipped baggage. – Check the way your baggage is fixed regularly. – If you carry any baggage, make sure it is fixed firmly as close as possible to the center of the vehicle and ensure even weight distribu- tion between the front and rear wheels.
Page 120: Riding Instructions
RIDING INSTRUCTIONS Checks and maintenance measures when preparing for use Info Before every trip, check the condition of the vehicle and ensure that it is roadworthy. The vehicle must be in perfect technical condition when it is being operated. – Check the engine oil level.
Page 121: Starting
RIDING INSTRUCTIONS Starting Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death. – When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed space without an effective exhaust extraction system.
Page 122: Starting Off
RIDING INSTRUCTIONS – Press the emergency OFF switch into the position – Switch on the ignition by turning the black programming key to the position ON After you switch on the ignition, you can hear the fuel pump working for about two seconds.
Page 123: Shifting, Riding
RIDING INSTRUCTIONS Shifting, riding Warning Danger of accidents Abrupt load alterations can cause the vehicle to get out of control. – Avoid abrupt load alterations and sudden braking actions, and adapt your speed to the road conditions. Warning Danger of accidents If you change down at high engine speed, the rear wheel can lock up. –...
Page 124 RIDING INSTRUCTIONS Warning Danger of accidents Reduced road grip with cold tires. – On every journey, take the first miles carefully at moderate speed until the tires reach operating temperature and optimal road grip is ensured. Warning Danger of accidents Reduced road grip with new tires. –...
Page 125 If you continue riding while the coolant temperature warning lamp is lit, the engine may be damaged. Info If you hear unusual noises while riding, stop immediately, switch off the engine and contact an authorized KTM workshop. – When conditions allow (incline, road situation, etc.), you can shift into a higher gear.
Page 126: Braking
Danger of accidents Reduced braking effect caused by spongy pressure point of front or rear brake. – Check the brake system and do not continue riding. (Your authorized KTM workshop will be pleased to help.) Warning Danger of accidents Failure of brake system.
Page 127: Stopping, Parking
RIDING INSTRUCTIONS Warning Danger of accidents Delayed brake action on salted roads. – There may be salt deposits on the brake discs. In order to restore the normal braking efficiency, you will need to remove the deposits from the discs by carefully applying the brakes. –...
Page 128: Transport
RIDING INSTRUCTIONS – Do not park the vehicle near flammable or explosive substances. Do not place objects on the vehicle while it is still warm from being run. Always let the vehicle cool first. Note Material damage Damage to or destruction of components due to excessive load. –...
Page 129: Refueling
RIDING INSTRUCTIONS Note Fire hazard Some vehicle components become very hot when the vehicle is operated. – Do not park the vehicle near flammable or explosive substances. Do not place objects on the vehicle while it is still warm from being run.
Page 130 – In some countries and regions, the available fuel quality and cleanliness may not be sufficient. This will result in problems with the fuel system. (Your authorized KTM workshop will be pleased to help.) – Only refuel with clean fuel that meets the specified standards.
Page 131: Service Schedule
● ● Check that the electrical equipment is functioning properly. ○ ● ● ● Read out the trouble code memory using the KTM diagnostics tool. ● ● ● Check the measured service values with the KTM diagnostics tool. ○ ●...
Page 132 Change the air filter. Clean the air filter box. ● ● ● Check the fuel pressure. ● ● ● Check the value of the manifold absolute pressure sensor (PM value) with the KTM diagnostics tool. ● ● ● Check the CO adjustment with the KTM diagnostics tool.
Page 133 Read out the fault memory using the KTM diagnostics tool after a test ride. ○ ● ● ● Set the service interval display. ○ ● ● ● Make the service entry in the KTM Dealer.net and in the Service and Warranty Booklet. ○ One-time interval ● Periodic interval...
Page 134: Tuning The Chassis
TUNING THE CHASSIS 10.1 Fork/shock absorber The fork and the shock absorber offer many options of adapting the chassis to your riding style and the payload. Info  To help you adapt the vehicle, we have summarized our findings in Table .
Page 135: Adjusting The Rebound Damping Of The Fork
TUNING THE CHASSIS – Turn adjusting screws  clockwise to the stop. Info The adjusting screws are located at the bottom end of the fork legs. Make the same adjustment on both fork legs. – Turn counterclockwise by the number of clicks corresponding to the fork type. Guideline Compression damping B00572-10...
Page 136: Adjusting The Spring Preload Of The Fork
TUNING THE CHASSIS – Turn adjusting screws  clockwise to the stop. Info The adjustment screws are located at the top end of the fork legs. Make the same adjustment on both fork legs. – Turn counterclockwise by the number of clicks corresponding to the fork type. Guideline Rebound damping Comfort...
Page 137: Compression Damping Of The Shock Absorber
TUNING THE CHASSIS – Turn adjusting screws  clockwise to the stop. Info The adjustment screws are located at the top end of the fork legs. Make the same adjustment on both fork legs. – Turn counterclockwise by the number of rotations corresponding to the fork type. Guideline Spring preload - Preload Adjuster Comfort...
Page 138: Adjusting The Low-Speed Compression Damping Of The Shock Absorber
Caution Danger of accidents Disassembly of pressurized parts can lead to injury. – The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will be pleased to help.) Info The low-speed setting can be seen during the slow to normal compression of the shock absorber.
Page 139: Adjusting The High-Speed Compression Damping Of The Shock Absorber
Caution Danger of accidents Disassembly of pressurized parts can lead to injury. – The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will be pleased to help.) Info The high-speed setting can be seen during the fast compression of the shock absorber.
Page 140: Adjusting The Rebound Damping Of The Shock Absorber
Adjusting the rebound damping of the shock absorber Caution Danger of accidents Disassembly of pressurized parts can lead to injury. – The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will be pleased to help.) – ...
Page 141 TUNING THE CHASSIS Info The spring preload defines the initial situation of the spring process on the shock absorber. The best spring preload setting is achieved when it is set for the weight of the rider and that of any baggage and a passenger, thus ensuring an ideal compromise between maneuverability and stability.
Page 142: Steering Damper
TUNING THE CHASSIS Info Turn clockwise to increase preload, turn counterclockwise to reduce spring preload. – Tighten screw  Guideline Remaining frame bolts 5 Nm (3.7 lbf ft) 100689-10 10.10 Steering damper The steering damper suppresses shocks to the steering arising from acceleration on uneven ground at high speed or when the load is temporarily taken from the front wheel.
Page 143: Adjusting The Steering Damper
TUNING THE CHASSIS 10.11 Adjusting the steering damper Info The hydraulic steering damper stabilizes the steering if the front wheel is raised off the ground or carries no load. In contrast to other damping elements, the steering damper is adjusted with the damping element open. –...
Page 144: Vehicle Level
TUNING THE CHASSIS 10.12 Vehicle level Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior. – Following modifications, ride slowly at first to get the feel of the new ride behav- ior. The vehicle level can be adjusted at the front by means of the fork leg clamp and at the rear by the eccentric shaft.
Page 145: Adjusting Front Vehicle Level
TUNING THE CHASSIS 10.13 Adjusting front vehicle level Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior. – Following modifications, ride slowly at first to get the feel of the new ride behavior. – ...
Page 146 TUNING THE CHASSIS Info The standard adjustment is the setting that provides the best vehicle handling. When the fork is compressed, the suspension setting changes, causing the vehi- cle to become more stable but also more difficult to handle. – Tighten screw ...
Page 147: Adjusting The Vehicle Level At The Rear
TUNING THE CHASSIS 10.14 Adjusting the vehicle level at the rear Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior. – Following modifications, ride slowly at first to get the feel of the new ride behavior. –...
Page 148: Footrest Position
TUNING THE CHASSIS – Tighten screw  Guideline Screw, clamp, eccentric shaft of deflec- 18 Nm (13.3 lbf ft) 100698-10 10.15 Footrest position The adjustable footrest system enables an individual setting of the footrest height and an individual adjustment of the controls. The lower footrest position enables a more comfortable knee angle, the upper footrest posi- tion a sporting sitting position and more forward-leaning freedom for use in racing.
Page 149 TUNING THE CHASSIS – Remove screws  B00561-10 –  Position the footrest bracket with spacers and screws. Guideline Standard Upper position Info The adjustable footrest bracket enables a more comfortable lower footrest posi- tion or a sporting upper footrest position. B00562-10 –...
Page 150 TUNING THE CHASSIS – Repeat adjustment work on the footrest bracket on the other side. – Adjust the shift lever. ( p. 150) – Adjust the foot brake lever. ( p. 154) 100702-01...
Page 151: Adjusting Shift Lever Stub
TUNING THE CHASSIS 10.17 Adjusting shift lever stub –  Remove the screw with the shift lever stub. –  Position the shift lever stub with the screw in one of the holes according to the desired lever length. Guideline Standard Central hole –...
Page 152: Adjusting The Foot Brake Lever Stub
TUNING THE CHASSIS 10.18 Adjusting the foot brake lever stub –  Remove the screw with the foot brake lever stub. –  Position the foot brake lever stub with the screw in one of the holes according to the desired lever length. Guideline Standard Central hole...
Page 153 TUNING THE CHASSIS – Remove screws  and take off the shift rod. –  Loosen lock nuts – Adjust the shift rod. Guideline Shift rod adjustment range 114… 153 mm (4.49… 6.02 in) Info Make the same adjustments on both sides. At least 5 screw threads must be screwed into the seating.
Page 154 TUNING THE CHASSIS – Position the shift rod. Guideline shift lever: upper drill hole,  Standard shift shaft: lower drill hole 0 0 A Medium shift force, medium shift shift lever: lower drill hole,  distance shift shaft: lower drill hole shift lever: lower drill hole, ...
Page 155 TUNING THE CHASSIS – Adjust the shift lever by turning the shift rod. Info The position of the shift lever can be greatly varied, depending on the length of the shift rod and the drill holes selected. As seen from the footrest, there ...
Page 156: Adjusting The Foot Brake Lever
TUNING THE CHASSIS 10.20 Adjusting the foot brake lever –   Use the tool to press in the anti-rotation lock , then turn the piston rod Info The range of adjustment is limited. – Remove the tool. The spring tension on the anti-rotation lock is released and the hex nut is locked. 100707-10 –...
Page 157: Handlebar Height/Position
TUNING THE CHASSIS – Move the foot brake lever back and forth between the end stop and the contact to the foot brake cylinder piston and check free travel  Guideline Free travel at foot brake lever 3… 5 mm (0.12… 0.2 in) Info The piston rod should not move in the process.
Page 158: Adjusting The Handlebar Height/Position
TUNING THE CHASSIS Handlebar position   The handlebar stubs can be set in position , enabling ergonomic adjustment of the handlebar position. Handlebar position difference 6.5° Standard  Position 600925-10 10.23 Adjusting the handlebar height/position Info The handlebar stub position must be identical on the left and right of the vehicle. Adjusting the high position of the handlebar stubs: –...
Page 159 TUNING THE CHASSIS – Remove distance sleeve  – All cables routed under the upper triple clamp must now be routed under the han- dlebar stub. – Push the handlebar stub carefully up to the upper triple clamp. Watch out for the handlebar position difference.
Page 160 TUNING THE CHASSIS Adjusting the low position of the handlebar stubs: –  Loosen screw Info Loosen the screw several turns to prevent damage to the fork paint when moving the handlebar stub. 100759-10 –   Remove screw with distance sleeve –...
Page 161 TUNING THE CHASSIS – Tighten the screw. Guideline Screw, handlebar stub 20 Nm (14.8 lbf ft) – Repeat the adjustments on the other handlebar stub. – Move the handlebar to and fro over the entire steering range. » If the cables restrict the freedom of movement of the steering: –...
Page 162 TUNING THE CHASSIS – Position the distance sleeve. –  Mount and tighten screw Guideline Remaining frame bolts 5 Nm (3.7 lbf ft) –  Tighten screw Guideline Screw, handlebar stub 20 Nm (14.8 lbf ft) 600986-10 – Repeat the adjustments on the other handlebar stub. –...
Page 163: Subframe Position
TUNING THE CHASSIS – Position the distance sleeve. –  Mount and tighten screw Guideline Remaining frame bolts 5 Nm (3.7 lbf ft) –  Tighten screw Guideline Screw, handlebar stub 20 Nm (14.8 lbf ft) 600986-11 – Repeat the adjustments on the other handlebar stub. –...
Page 164: Adjusting The Subframe Position
TUNING THE CHASSIS 10.25 Adjusting the subframe position Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior. – Following modifications, ride slowly at first to get the feel of the new ride behavior. Preparatory work –...
Page 165 TUNING THE CHASSIS – Mount the screws with the washer on the left and right sides of the vehicle but do not tighten yet. B01319-01 –  Remove screws with the washers on the left and right sides of the vehicle. –...
Page 166 TUNING THE CHASSIS Lowering the seat position: –  Remove screws with the washers on the left and right sides of the vehicle. – Push down on the subframe until the drilled holes of the frame are aligned with the holes at the top rear of the subframe.
Page 167 TUNING THE CHASSIS – Tighten screws  on the left and right sides of the vehicle. Guideline Screw, subframe 20 Nm Loctite ® 243™ (14.8 lbf ft) Info Check the cable routing; the lambda sensor cable should not be taut. B01318-12 –...
Page 168 TUNING THE CHASSIS Finishing work – Fit the seat. ( p. 170)
Page 169: Service Work On The Chassis
SERVICE WORK ON THE CHASSIS 11.1 Raising the rear of the motorcycle with lifting gear Note Danger of damage The parked vehicle may roll away or fall over. – Always place the vehicle on a firm and even surface. – Insert the adapter into the lifting gear at the rear. Adapter (61029055120) Rear wheel stand (61029055400) –...
Page 170: Raising The Front Of The Motorcycle With Lifting Gear
SERVICE WORK ON THE CHASSIS 11.3 Raising the front of the motorcycle with lifting gear Note Danger of damage The parked vehicle may roll away or fall over. – Always place the vehicle on a firm and even surface. Preparatory work –...
Page 171: Bleeding Fork Legs
SERVICE WORK ON THE CHASSIS 11.5 Bleeding fork legs Preparatory work – Lean the motorcycle on the side stand. Main work –  Release bleeder screws Any excess pressure escapes from the interior of the fork. – Tighten the bleeder screws. Info Perform this action on both fork legs.
Page 172: Fitting The Seat
SERVICE WORK ON THE CHASSIS 11.7 Fitting the seat – Position the recesses of the seat to the lugs on the frame, lower the rear end and simul- taneously push it forward. – Lock the seat by turning the ignition key in the seat lock. –...
Page 173: Removing The Passenger Seat
SERVICE WORK ON THE CHASSIS 11.9 Removing the passenger seat – Remove the seat. ( p. 169) –  Activate the release lever –  Take off the passenger seat toward the top. B01325-10 11.10 Mounting the passenger seat Warning Danger of accidents The passenger seat can come loose from the anchoring if it is not mounted correctly.
Page 174: Checking For Chain Dirt
SERVICE WORK ON THE CHASSIS 11.11 Checking for chain dirt – Check the chain for loose dirt. » If the chain is very dirty: – Clean the chain. ( p. 172) 400678-01 11.12 Cleaning the chain Warning Danger of accidents Oil or grease on the tires reduces their grip. –...
Page 175: Checking The Chain Tension
SERVICE WORK ON THE CHASSIS Info The service life of the chain depends largely on its maintenance. – Clean the chain regularly. – Rinse off loose dirt with a soft jet of water. – Remove old grease remains with chain cleaner. Chain cleaner ( p.
Page 176: Adjusting The Chain Tension
SERVICE WORK ON THE CHASSIS – Lean the motorcycle on the side stand. – Shift into neutral. – Push the chain upwards where the chain passes through the swingarm and measure  chain tension Info  The lower chain section must be taut.
Page 177 SERVICE WORK ON THE CHASSIS Main work –  Loosen nut – Loosen nuts  –  Adjust chain tension by turning the adjustment screws on the left and right. Guideline Chain tension 15… 20 mm (0.59… 0.79 in)  Turn adjusting screws on the left and right so that the markings on the left and ...
Page 178: Checking The Chain, Rear Sprocket And Engine Sprocket
SERVICE WORK ON THE CHASSIS 11.15 Checking the chain, rear sprocket and engine sprocket – Check the rear sprocket and engine sprocket for wear. » If the rear sprocket and engine sprocket are worn: – Change the power set. Info The engine sprocket, rear sprocket and chain should always be replaced together.
Page 179 SERVICE WORK ON THE CHASSIS – Shift into neutral. –  Pull the lower chain section with specified weight Guideline Weight, chain wear measurement 15 kg (33 lb.) –  Measure the distance of 18 chain links in the lower chain section. Info Chain wear is not always even, so you should repeat this measurement at differ- ent chain positions.
Page 180 SERVICE WORK ON THE CHASSIS – Check the chain sliding guard for wear at the opening. »   If the rivets of the chain are no longer visible at the lower edge of the open- ing of the chain sliding guard: –...
Page 181: Adjusting Basic Position Of Clutch Lever
SERVICE WORK ON THE CHASSIS 11.16 Adjusting basic position of clutch lever – Adjust the basic setting of the clutch lever to your hand size by turning adjusting  screw Info Turn the adjusting screw clockwise to increase the distance between the clutch lever and the handlebar.
Page 182: Correcting Fluid Level Of Hydraulic Clutch
SERVICE WORK ON THE CHASSIS – Check the fluid level. The fluid level must be between the MIN and MAX markings. » If the coolant level does not meet specifications: – Correct the fluid level of the hydraulic clutch. ( p.
Page 183: Brake System
Danger of accidents Reduced braking efficiency due to worn brake disc(s). – Change the worn brake disc(s) without delay. (Your authorized KTM workshop will be pleased to help.) – Check the thickness of the brake disc in several places to see if it is within the speci- ...
Page 184: Checking The Rear Brake Disc
Danger of accidents Reduced braking efficiency due to worn brake disc(s). – Change the worn brake disc(s) without delay. (Your authorized KTM workshop will be pleased to help.) – Check the thickness of the brake disc in several places to see if it conforms to measure- ...
Page 185: Checking The Front Brake Fluid Level
Warning Danger of accidents Reduced braking efficiency due to old brake fluid. – Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be pleased to help.) – Move the brake fluid reservoir mounted on the handlebar to a horizontal position.
Page 186 Warning Danger of accidents Reduced braking efficiency due to old brake fluid. – Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be pleased to help.) Warning Environmental hazard Hazardous substances cause environmental damage.
Page 187: Checking The Front Brake Linings
Checking the front brake linings Warning Danger of accidents Reduced braking efficiency caused by worn brake linings. – Change worn brake linings immediately. (Your authorized KTM workshop will be pleased to help.) Note Danger of accidents Reduced braking efficiency caused by damaged brake discs. –...
Page 188: Checking The Rear Brake Fluid Level
(Your authorized KTM workshop will be pleased to help.) Warning Danger of accidents Reduced braking efficiency due to old brake fluid. – Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be pleased to help.)
Page 189: Adding Rear Brake Fluid
If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately. Warning Danger of accidents Reduced braking efficiency due to old brake fluid. – Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be pleased to help.)
Page 190 BRAKE SYSTEM Warning Environmental hazard Hazardous substances cause environmental damage. – Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations. Info Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5 brake fluid.
Page 191: Checking The Rear Brake Linings
Checking the rear brake linings Warning Danger of accidents Reduced braking efficiency caused by worn brake linings. – Change worn brake linings immediately. (Your authorized KTM workshop will be pleased to help.) Note Danger of accidents Reduced braking efficiency caused by damaged brake discs. –...
Page 192: Wheels, Tires
WHEELS, TIRES 13.1 Removing the front wheel Preparatory work – Raise the rear of the motorcycle with lifting gear. ( p. 167) – Raise the front of the motorcycle with lifting gear. ( p. 168) Main work –  Remove the screws from both brake calipers.
Page 193: Installing The Front Wheel
WHEELS, TIRES – Remove spacers  C00336-10 13.2 Installing the front wheel – Check the wheel bearing for damage and wear. » If the wheel bearing is damaged or worn: – Replace the wheel bearing. –   Clean and grease the shaft seal rings and mating surfaces of the spacers.
Page 194 WHEELS, TIRES – Insert the wide spacer on the left-hand side  (when looking in the direction of travel). Info  The arrow indicates the direction of rotation of the front wheel. – Insert the narrow spacer on the right-hand side (when viewed in the direction of travel). C00337-10 Warning Danger of accidents Reduced braking efficiency due to oil or grease on the...
Page 195 WHEELS, TIRES – Position the brake calipers. The brake linings are correctly positioned. –  Mount screws on both brake calipers but do not tighten yet. – Operate the hand brake lever repeatedly until the brake linings are in contact with the brake disc and there is a pressure point.
Page 196: Removing The Rear Wheel
WHEELS, TIRES 13.3 Removing the rear wheel Preparatory work – Raise the rear of the motorcycle with lifting gear. ( p. 167) Main work –  Remove nut –  Remove chain adjuster –  Remove wheel spindle C00339-10 – Push the rear wheel as far forward as possible and then remove the chain from the rear sprocket.
Page 197: Installing The Rear Wheel
WHEELS, TIRES 13.4 Installing the rear wheel Warning Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs. – Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary. Warning Danger of accidents No braking effect when operating the rear brake.
Page 198 WHEELS, TIRES – Push the brake caliper frame  completely to the rear. – Position the rear wheel. The brake caliper support and brake linings are correctly positioned. C00343-10 – Push the rear wheel as far forward as possible and place the chain on the rear sprocket. –...
Page 199: Checking Rear Hub Cush Drive
WHEELS, TIRES – Place the chain adjuster  on the tensioning screw. –  Position the chain adjuster and place it on the tensioning screw. –  Tighten nut Guideline In order for the rear wheel to be correctly aligned, the markings on the left and right chain adjusters must be in the same position relative to the reference marks ...
Page 200: Checking The Tire Condition
Danger of accidents Uncontrollable vehicle handling in the event of a flat tire. – In the interest of safety, replace damaged or worn tires immediately. (Your authorized KTM workshop will be pleased to help.) Warning Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.
Page 201 WHEELS, TIRES Warning Danger of accidents Uncontrollable handling characteristic due to non-approved and/or non-recommended tires/wheels. – Only tires/wheels approved by KTM and with the corresponding speed index should be used. Warning Danger of accidents Reduced road grip with new tires. – New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be rough- ened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles.
Page 202: Checking The Tire Pressure
DOT marking. The first two digits refer to the week of manufacture and last two digits refer to the year of manufacture. KTM recommends that the tires are changed regardless of the actual wear, at the latest after five years.
Page 203 WHEELS, TIRES – Mount the dust cap. Info The rubber seal in the dust cap prevents air from leaking out of the tire if the valve is defective.
Page 204: Electrical System
ELECTRICAL SYSTEM 14.1 Removing the battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns. – Keep batteries out of the reach of children. – Wear suitable protective clothing and goggles. – Avoid contact with battery acid and battery gases. –...
Page 205 ELECTRICAL SYSTEM Main work –  Disconnect negative cable from the battery. B01328-10 – Remove the cover of the positive terminal. –  Disconnect positive cable from the battery. B01329-10 –  Remove screws –  Remove holder – Lift out the battery. B01329-11...
Page 206: Installing The Battery
ELECTRICAL SYSTEM 14.2 Installing the battery Main work – Position the battery in the battery compartment. Guideline The poles of the battery must face the rear of the vehicle. Battery (YTZ14S) ( p. 261) –  Position holder – Mount and tighten screws ...
Page 207: Recharging The Battery
Environmental hazard The battery contains elements that are harmful to the environment. – Do not dispose of batteries with the household waste. Dispose of a defective battery in an environmentally friendly manner. Give the battery to your authorized KTM dealer or dispose of it at a collection point for used batteries.
Page 208 ELECTRICAL SYSTEM Warning Environmental hazard Hazardous substances cause environmental damage. – Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations. Info Even when there is no load on the battery, it discharges steadily. The charge state and the type of charge are very important for the service life of the battery.
Page 209 ELECTRICAL SYSTEM Main work – Connect the battery charger to the battery. Switch on the battery charger. Battery charger (58429074000) You can also use the battery charger to test the rest potential and start potential of the battery, and to test the alternator. With this device, you cannot overcharge the battery. Info ...
Page 210: Changing The Main Fuse
ELECTRICAL SYSTEM 14.4 Changing the main fuse Warning Fire hazard The electrical system can be overloaded if the wrong fuses are used. – Use only fuses with the prescribed amperage. Never bypass or repair fuses. Info The main fuse protects all power consumers of the vehicle. The main fuse is under the seat. Preparatory work –...
Page 211 ELECTRICAL SYSTEM Main work –  Remove protection covers – Remove the faulty main fuse  Info  A reserve fuse is located in the starter relay. – Install a new main fuse. Fuse (58011109130) ( p. 261) Place the spare fuse in the starter relay so that it is available if needed. –...
Page 212: Changing The Fuses Of Individual Power Consumers
ELECTRICAL SYSTEM 14.5 Changing the fuses of individual power consumers Warning Fire hazard The electrical system can be overloaded if the wrong fuses are used. – Use only fuses with the prescribed amperage. Never bypass or repair fuses. Info The fuse box containing the fuses of individual power consumers is located under the seat. Preparatory work –...
Page 213 ELECTRICAL SYSTEM – Check the fuses. Info  A defective fuse can be identified by the burned-out fuse wire – Remove the faulty fuse. Guideline Fuse 1 - 10 A - ignition, combination instrument, immobilizer, alarm system (optional) 305696-10 Fuse 2 - 15 A - high beam, low beam, parking light, tail light, license plate lamp Fuse 3 - 10 A - horn, brake light Fuse 4 - 10 A - radiator fan Fuse 5 - 10 A - fuel pump...
Page 214: Changing The Low Beam Bulb
ELECTRICAL SYSTEM – Close the fuse box cover. Finishing work – Fit the seat. ( p. 170) 14.6 Changing the low beam bulb Note Damage to reflector Reduced brightness. – Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before mounting.
Page 215 ELECTRICAL SYSTEM – Push latch  in the direction of the arrow. –  Remove the lamp cover 100743-10 –  Unplug connector –  Push off the retaining clamp on both sides, squeeze and fold to the side. – Remove headlight bulb ...
Page 216 ELECTRICAL SYSTEM – Position lug  of the lamp cover in the notch. –  Engage latch – Check that the lighting is functioning properly. 401161-10 –  Position the rubber holder –  Fold down the combination instrument. Position the lug in the rubber retainer.
Page 217: Changing The High Beam Bulb
ELECTRICAL SYSTEM 14.7 Changing the high beam bulb Note Damage to reflector Reduced brightness. – Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before mounting.
Page 218 ELECTRICAL SYSTEM – Unplug connector  –  Push off the retaining clamp on both sides, squeeze and fold to the side. – Remove headlight bulb. – Position the new headlight bulb in the headlight housing. Guideline Insert the headlight bulb so that the lug is positioned in the cut-out. Low beam / high beam (H7 / base PX26d) ( p.
Page 219 ELECTRICAL SYSTEM – Position lug  of the lamp cover in the notch. – Engage the latch. – Check that the lighting is functioning properly. 401161-11 – Position the cover. Info Check for correct positioning and freedom of movement of the brake lines. –...
Page 220: Checking The Headlight Setting
ELECTRICAL SYSTEM 14.8 Checking the headlight setting – Stand the vehicle upright on a horizontal surface in front of a light wall and make a 0 0 A mark at the height of the center of the low beam headlight. –...
Page 221: Activating/Deactivating Ignition Key
ELECTRICAL SYSTEM Main work –  Turn the screw to adjust the headlight range. Guideline A motorcycle with rider, including the luggage and a passenger (where applicable) the light cut off must be aligned exactly on the lower mark (when checking headlight adjustment).
Page 222 ELECTRICAL SYSTEM – Insert the orange programming key in the ignition lock. – Switch on the ignition by turning the orange programming key to the ON position EFI warning lamp (MIL) lights up, switches off, and then starts to flash. The immobilizer indicator lamp lights up.
Page 223 ELECTRICAL SYSTEM Loss of both black ignition keys (no black ignition key available): This procedure is important to prevent misuse of the lost black ignition key. – Press the emergency OFF switch into the position 401114-11 – Insert the orange programming key in the ignition lock. –...
Page 224 ELECTRICAL SYSTEM programmed during the activation procedure are invalid, but can be reprogrammed in a further activation procedure. – Press the emergency OFF switch into the position – Insert the orange programming key in the ignition lock. – Switch on the ignition by turning the orange programming key to the ON position EFI warning lamp (MIL) lights up, switches off, and then starts to flash.
Page 225: Cooling System
COOLING SYSTEM 15.1 Cooling system  The water pump with a 3D water pump wheel in the engine ensures forced circulation of the coolant. The heat exchanger enables faster warming of the engine oil at the start of a journey and better heat dissipation for the engine oil during the journey. The pressure in the cooling system resulting from heat is regulated by a valve in the radia- ...
Page 226: Filling Cooling System Compensating Tank
COOLING SYSTEM Condition The engine is cold. The radiator is completely full. – Rest the motorcycle on its side stand on a horizontal surface. – Check the coolant level in the compensating tank. The coolant level must be between MIN and MAX. »...
Page 227 After draining coolant and refilling the cooling system, the motorcycle must be raised at the front according to the model type. This is the only way of ensuring that the cooling system is filled without air bubbles. (Your authorized KTM workshop will be pleased to help.) –...
Page 228: Tuning The Engine
TUNING THE ENGINE 16.1 Checking the play in the throttle cable – Check the throttle grip for smooth operation. – Move the handlebar to the straight-ahead position. Move the throttle grip backwards and forwards to ascertain the play in the throttle cable. Throttle cable play 3…...
Page 229: Adjusting The Play In The Throttle Cable
Adjusting the play in the throttle cable – Move the handlebar to the straight-ahead position. – Throttle position sensor circuit A - check in zero position. Info It is imperative to use the KTM diagnostics tool for this. –  Push back protection cap – ...
Page 230: Service Work On The Engine
SERVICE WORK ON THE ENGINE 17.1 Checking the engine oil level Condition The engine is at operating temperature. Preparatory work – Stand the motorcycle upright on a horizontal surface. Main work –  Remove oil dipstick . Check the engine oil level in the measurement range. Info After switching off the engine, wait one minute before checking the level.
Page 231: Draining Engine Oil, Cleaning Oil Screens
SERVICE WORK ON THE ENGINE 17.3 Draining engine oil, cleaning oil screens Warning Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden. – Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water. Warning Environmental hazard Hazardous substances cause environmental damage.
Page 232 SERVICE WORK ON THE ENGINE – Remove screws  –  Take off the left exhaust cover B01335-10 – Stand the motorcycle on its side stand on a level surface. – Place a suitable container under the engine. –  Remove the oil drain plugs with the magnets, O-rings, and oil screens.
Page 233 SERVICE WORK ON THE ENGINE – Thoroughly clean magnets  and oil screens  of the oil drain plugs. 100773-10 – Mount and tighten the oil drain plugs with the magnets, O-rings, and oil screens. Guideline Oil drain plug M20x1.5 20 Nm (14.8 lbf ft) –...
Page 234: Removing The Oil Filter
SERVICE WORK ON THE ENGINE – Position the left exhaust cover  –  Mount and tighten screws Guideline Screw, painted trim parts 3.5 Nm (2.58 lbf ft) B01335-10 17.4 Removing the oil filter Warning Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden. –...
Page 235 SERVICE WORK ON THE ENGINE Warning Environmental hazard Hazardous substances cause environmental damage. – Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations. Preparatory work – Place a suitable container under the engine. Main work –...
Page 236: Installing The Oil Filter
SERVICE WORK ON THE ENGINE 17.5 Installing the oil filter –  Insert oil filter –  Lubricate the O-ring of the oil filter cover. Position oil filter cover – Mount and tighten the screws. Guideline Remaining engine screws 6 Nm (4.4 lbf ft) 100776-10 17.6 Filling up with engine oil...
Page 237 SERVICE WORK ON THE ENGINE Engine oil (1st 3.00 l (3.17 qt.) External Engine oil quantity) temperature: (SAE 10W/50) ≥ 0 °C (≥ 32 °F) p. 268) External Engine oil (SAE temperature: 5W/40) ( p. 269) < 0 °C (< 32 °F) –...
Page 238: Adding Engine Oil
SERVICE WORK ON THE ENGINE Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death. – When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed space without an effective exhaust extraction system.
Page 239 SERVICE WORK ON THE ENGINE Info For optimal performance of the engine oil, do not mix different types of engine oil. If appropriate, change the engine oil. –  Replace oil dipstick Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death.
Page 240: Cleaning, Care
CLEANING, CARE 18.1 Cleaning motorcycle Note Material damage Damage and destruction of components by high-pressure cleaning equipment. – When cleaning the vehicle with a pressure cleaner, do not point the water jet directly onto electrical components, connectors, cables, bearings, etc. Maintain a minimum distance of 60 cm between the nozzle of the pressure cleaner and the component. Excessive pres- sure can cause malfunctions or destroy these parts.
Page 241 CLEANING, CARE – After rinsing the motorcycle with a gentle spray of water, allow it to dry thoroughly. – Remove the plug from the exhaust system. Warning Danger of accidents Reduced braking efficiency due to a wet or dirty brake sys- tem.
Page 242: Checks And Maintenance Steps For Winter Operation
CLEANING, CARE 18.2 Checks and maintenance steps for winter operation Info If the motorcycle is used in the winter, salt can be expected on the roads. Precautions need to be taken against road salt corrosion. If the vehicle was operated in road salt, clean it with cold water after riding. Warm water intensifies the effects of salt. –...
Page 243: Storage
205) Guideline Storage temperature of battery without 0… 35 °C (32… 95 °F) direct sunshine. – Store the vehicle in a dry location that is not subject to large fluctuations in tempera- ture. Info KTM recommends raising the motorcycle.
Page 244: Preparing For Use After Storage
STORAGE – Raise the rear of the motorcycle with lifting gear. ( p. 167) – Raise the front of the motorcycle with lifting gear. ( p. 168) – Cover the motorcycle with a porous sheet or blanket. Info Do not use non-porous materials since they prevent humidity from escaping, thus causing corrosion.
Page 245: Troubleshooting
OFF switch defective – Check the emergency OFF switch. – Safety start system defective Read out the trouble code memory using the KTM diagnostics tool. – Immobilizer active Read the immobilizer blink code. – EFI control unit not activated Encode the EFI control unit.
Page 246 Action – Engine cranks but doesn't start Fault in fuel injection system Read out the trouble code memory using the KTM diagnostics tool. – Fuel pump control defective Read out the trouble code memory using the KTM diagnostics tool. –...
Page 247 TROUBLESHOOTING Faults Possible cause Action – High oil consumption Engine oil too thin (viscosity) Change the engine oil and filter, clean the oil screen. p. 228) – Headlight and parking light do not Fuse 2 blown Change the fuses of individual power consumers. work p.
Page 248: Immobilizer Blink Code
IMMOBILIZER BLINK CODE Blink code of immobilizer indica- tor lamp 12 Immobilizer indicator lamp flashes 1x short, 1 second pause, 2x short Error level condition All ignition keys inactive Blink code of immobilizer indica- tor lamp 13 Immobilizer indicator lamp flashes 1x short, 1 second pause, 3x short Error level condition ICU antenna malfunction Blink code of immobilizer indica-...
Page 249 IMMOBILIZER BLINK CODE Blink code of immobilizer indica- tor lamp 31 Immobilizer indicator lamp flashes 3x short, 1 second pause, 1x short Error level condition Malfunction, encryption query from EFI control unit to immobilizer control unit Blink code of immobilizer indica- tor lamp 32 Immobilizer indicator lamp flashes 3x short, 1 second pause, 2x short Error level condition...
Page 250: Engine Control Blink Code
ENGINE CONTROL BLINK CODE Blink code EFI warning lamp (MIL) 02 EFI warning lamp (MIL) flashes 2x short Error level condition Crankshaft position sensor - circuit fault Blink code EFI warning lamp (MIL) 06 EFI warning lamp (MIL) flashes 6x short Error level condition Throttle position sensor circuit A - input signal too low Throttle position sensor circuit A - input signal too high...
Page 251 ENGINE CONTROL BLINK CODE Blink code EFI warning lamp (MIL) 12 EFI warning lamp (MIL) flashes 1x long, 2x short Error level condition Engine coolant temperature sensor - input signal too low Engine coolant temperature sensor - input signal too high Blink code EFI warning lamp (MIL) 13 EFI warning lamp (MIL) flashes 1x long, 3x short Error level condition...
Page 252 ENGINE CONTROL BLINK CODE Blink code EFI warning lamp (MIL) 18 EFI warning lamp (MIL) flashes 1x long, 8x short Error level condition Lambda sensor cylinder 2, sensor 1 - circuit fault Blink code EFI warning lamp (MIL) 22 EFI warning lamp (MIL) flashes 2x long, 2x short Error level condition Gear position sensor - circuit fault Blink code EFI warning lamp (MIL)
Page 253 ENGINE CONTROL BLINK CODE Blink code EFI warning lamp (MIL) 37 EFI warning lamp (MIL) flashes 3x long, 7x short Error level condition Ignition coil 1, cylinder 1 - circuit fault Blink code EFI warning lamp (MIL) 38 EFI warning lamp (MIL) flashes 3x long, 8x short Error level condition Ignition coil 1, cylinder 2 - circuit fault Blink code EFI warning lamp (MIL)
Page 254 ENGINE CONTROL BLINK CODE Blink code EFI warning lamp (MIL) 45 EFI warning lamp (MIL) flashes 4x long, 5x short Error level condition Lambda sensor heater cylinder 1, sensor 1 - short circuit to ground or open circuit Lambda sensor heater cylinder 1, sensor 1 - input signal too high Blink code EFI warning lamp (MIL) 46 EFI warning lamp (MIL) flashes 4x long, 6x short Error level condition...
Page 255 ENGINE CONTROL BLINK CODE Blink code EFI warning lamp (MIL) 68 EFI warning lamp (MIL) flashes 6x long, 8x short Error level condition Manifold absolute pressure sensor cylinder 1 - connection leaks Blink code EFI warning lamp (MIL) 69 EFI warning lamp (MIL) flashes 6x long, 9x short Error level condition Manifold absolute pressure sensor cylinder 2 - connection leaks Blink code EFI warning lamp (MIL)
Page 256: Technical Data
TECHNICAL DATA 23.1 Motor Design 2-cylinder 4-stroke Otto engine, 75° V arrangement, water-cooled Displacement 1,195 cm³ (72.92 cu in) Stroke 69 mm (2.72 in) Bore 105 mm (4.13 in) Compression ratio 13.5:1 Control DOHC, 4 valves per cylinder, chain-driven Valve - valve stem diameter Intake 42 mm (1.65 in) Exhaust...
Page 257: Motor Tightening Torques
TECHNICAL DATA 1st gear 14:36 2nd gear 16:30 3rd gear 20:30 4th gear 21:27 5th gear 23:26 6th gear 25:26 Mixture preparation Electronically controlled fuel injection Ignition system Contactless controlled fully electronic ignition with digital ignition adjustment Alternator 12 V, 450 W Spark plug Inside spark plug NGK LKAR9BI9...
Page 258 TECHNICAL DATA Screw, gear sensor 6 Nm (4.4 lbf ft) Loctite ® 243™ Screw, pulse generator 6 Nm (4.4 lbf ft) Loctite ® 243™ – Camshaft drive sprocket bolt 14 Nm (10.3 lbf ft) M6 – 10.9 Loctite ® 648™ Freewheel ring bolt 15 Nm (11.1 lbf ft) –...
Page 259 TECHNICAL DATA – Stud, chain shaft 8 Nm (5.9 lbf ft) Vacuum connection 2.5 Nm (1.84 lbf ft) Loctite ® 243™ Oil nozzle M6x0.75 4 Nm (3 lbf ft) Loctite ® 243™ – Plug, crankshaft retainer 15 Nm (11.1 lbf ft) M8 –...
Page 260: Capacities
TECHNICAL DATA – Screw, timing chain tensioner release M10x1 10 Nm (7.4 lbf ft) – Spark plug M10x1 15 Nm (11.1 lbf ft) Cylinder head screw M11x1.5 Tightening sequence: Lubricated with engine oil Using a crisscross pattern Step 1 15 Nm (11.1 lbf ft) Step 2 30 Nm (22.1 lbf ft) Step 3...
Page 261: Coolant
TECHNICAL DATA Engine oil 3.60 l (3.8 qt.) External temperature: < 0 °C Engine oil (SAE 5W/40) (< 32 °F) p. 269) 23.3.2 Coolant Coolant 2.60 l (2.75 qt.) Coolant ( p. 268) 23.3.3 Fuel Total fuel tank capacity, approx. 16.5 l (4.36 US gal) Super unleaded (ROZ 95/RON 95/PON 91) ( p.
Page 262 TECHNICAL DATA Rear 220 mm (8.66 in) Brake discs - wear limit Front 4.5 mm (0.177 in) Brake disc - wear limit Rear 4.5 mm (0.177 in) Tire air pressure, solo Front 2.5 bar (36 psi) Rear 2.5 bar (36 psi) Tire air pressure with passenger / full payload Front 2.5 bar (36 psi)
Page 263: Electrical System
W5W / base W2.1x9.5d 12 V 23.6 Tires Front tires Rear tires 120/70 ZR 17 M/C 58W TL 190/55 ZR 17 M/C 75W TL Continental Conti SportAttack 2 Continental Conti SportAttack 2 Additional information is available in the Service section under: http://www.ktm.com...
Page 264: Fork
TECHNICAL DATA 23.7 Fork Fork part number 05.18.7K.07 Fork WP Suspension Up Side Down 4354 Compression damping Comfort 20 clicks Standard 15 clicks Sport 15 clicks Full payload 15 clicks Rebound damping Comfort 20 clicks Standard 20 clicks Sport 10 clicks Full payload 10 clicks Spring preload - Preload Adjuster...
Page 265: Shock Absorber
TECHNICAL DATA 23.8 Shock absorber Shock absorber part number 17.18.7K.07 Shock absorber WP Suspension 4014 VP Compression damping, high-speed Comfort 3 turns Standard 2.5 turns Sport 1.5 turns Full payload 1.5 turns Compression damping, low-speed Comfort 20 clicks Standard 20 clicks Sport 20 clicks Full payload...
Page 266: Chassis Tightening Torques
TECHNICAL DATA Medium (standard) 85 N/mm (485 lb/in) Hard 95 N/mm (542 lb/in) Spring length 160 mm (6.3 in) Gas pressure 10 bar (145 psi) Static sag 11… 15 mm (0.43… 0.59 in) Riding sag 28… 35 mm (1.1… 1.38 in) Inbuilt length 290 mm (11.42 in) Shock absorber fluid (...
Page 267 TECHNICAL DATA – Screw, exhaust clamp 8 Nm (5.9 lbf ft) – Screw, exhaust heat shield 15 Nm (11.1 lbf ft) Screw, foot brake cylinder 10 Nm (7.4 lbf ft) Loctite ® 243™ Loctite ® 243™ Screw, foot brake lever 15 Nm (11.1 lbf ft) –...
Page 268 TECHNICAL DATA Screw, rear brake disc 30 Nm (22.1 lbf ft) Loctite ® 243™ – Screw, rear footrest bracket 25 Nm (18.4 lbf ft) – Screw, rear footrest bracket (footrest M8x25 15 Nm (11.1 lbf ft) bracket not mounted) Screw, shift lever 25 Nm (18.4 lbf ft) Loctite ®...
Page 269 TECHNICAL DATA Nut, swingarm pivot M19x1.5 130 Nm (95.9 lbf ft) Thread greased – Screw, seat lock M22x1.5 8 Nm (5.9 lbf ft) – Bolt, front axle M25x1.5 45 Nm (33.2 lbf ft) Nut, rear wheel spindle M25x1.5 90 Nm (66.4 lbf ft) Thread greased –...
Page 270: Substances
SUBSTANCES Brake fluid DOT 4 / DOT 5.1 Standard/classification – Guideline – Use only brake fluid that complies with the specified standard (see specifications on the container) and that exhibits the corresponding properties. Recommended supplier Castrol – RESPONSE BRAKE FLUID SUPER DOT 4 Motorex ®...
Page 271 SUBSTANCES Guideline – Use only engine oils that comply with the specified standards (see specifications on the container) and that possess the corresponding properties. Fully synthetic engine oil Recommended supplier Motorex ® – Power Synt 4T Engine oil (SAE 5W/40) Standard/classification –...
Page 272 SUBSTANCES Recommended supplier Motorex ® – Racing Fork Oil Hydraulic fluid (15) Standard/classification – ISO VG (15) Guideline – Use only hydraulic oil that complies with the specified standard (see specifications on the container) and that possesses the corre- sponding properties. Recommended supplier Motorex ®...
Page 273: Standard/Classification
SUBSTANCES Info Do not use fuel containing methanol (e. g. M15, M85, M100) or more than 10 % ethanol (e. g. E15, E25, E85, E100). Super unleaded (ROZ 98 / RON 98 / PON 94) Standard/classification – DIN EN 228 (ROZ 98 / RON 98 / PON 94)
Page 274: Auxiliary Substances
AUXILIARY SUBSTANCES Chain cleaner Recommended supplier Motorex ® – Chain Clean Chain lube for road use Guideline Recommended supplier Motorex ® – Chainlube Road Fuel additive Recommended supplier Motorex ® – Fuel Stabilizer Long-life grease Recommended supplier Motorex ® – Bike Grease 2000 Motorcycle cleaner Recommended supplier...
Page 275 AUXILIARY SUBSTANCES Preserving materials for paints, metal and rubber Recommended supplier Motorex ® – Moto Protect Special cleaner for glossy and matte paint finishes, metal and plastic surfaces Recommended supplier Motorex ® – Quick Cleaner Universal oil spray Recommended supplier Motorex ®...
Page 276: Standards
STANDARDS JASO T903 MA Different technical development directions required a new specification for 4-stroke motorcycles – the JASO T903 MA Standard. Ear- lier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle specification. Whereas long service intervals are demanded for automobile engines, high performance at high engine speeds are in the foreground for motorcycle engines.
Page 277: Index
INDEX rear brake, checking ......189 INDEX Brakes ........124 Accessories .
Page 278 INDEX fuel and external temperature menu, FUEL . 53, 61, 87, 90-91 UNITS menu ......77, 89, 92 fuel consumption menu (gallons), SET GAL US/UK .
Page 279 INDEX Fuel reserve display TRIP F RESET setting ........101 Figures .
Page 280 INDEX removing the front from the lifting gear ... . . 168 Immobilizer ........44 removing the rear from the lifting gear .
Page 281 INDEX Preparing for use Seat lock ........109 after storage .
Page 282 INDEX Steering damper ....... Tire condition adjusting ........141 checking .
Page 283 *3213285en* 3213285en 11/2014 KTM Sportmotorcycle GmbH Photo: Mitterbauer/KTM 5230 Mattighofen/Austria http://www.ktm.com...

KTM 1190 RC8 R Owner's Manual

1 Means of Representation

2 Safety Advice

3 Important Notes

4 View of Vehicle

5 Serial Numbers

6 Controls

7 Preparing for Use

8 Riding Instructions

10 Tuning the Chassis

11 Service Work on the Chassis

12 Brake System

13 Wheels, Tires

14 Electrical System

15 Cooling System

16 Tuning the Engine

17 Service Work on the Engine

18 Cleaning, Care

19 Storage

20 Troubleshooting

21 Immobilizer Blink Code

22 Engine Control Blink Code

23 Technical Data

24 Substances

25 Auxiliary Substances

26 Standards

Quick Links

Related Manuals for KTM 1190 RC8 R

Summary of Contents for KTM 1190 RC8 R