Christie Mirage S+14K User Manual page 101

Downloaded From projector-manual.com Christie Manuals
Table 3.4. System Error Codes
Code Description
GENERAL
12 Software error. Contact dealer/factory.
13 CRC error in flash ROM. Download new software.
14 Engineering-only programming is complete. Call Christie, replace TIPM.
15 Attempting to download s/w code without being in boot mode
16 Invalid interrupt. Power off/on. If persists, contact dealer/factory.
17 User has forced system to stay in boot mode
18 Attempting to program boot mode without jumper
LAMP / BALLAST
20 The lamp is unexpectedly on (likely a ballast and/or wiring problem)
21 Lamp airflow is low; overheating imminent
23 Cannot read valid ballast ID
26 Lamp door is open, or lamp is not installed (interlock)
27 Lamp cannot ignite
28 Lamp has turned off unexpectedly
29 Lamp ballast is overheated
2D Unknown or invalid Ballast ID, usually caused by faulty ballast cable or faulty ballast.
POWER & COOLING
46 Red DMD heatsink has overheated
47 Green DMD heatsink has overheated
48 Blue DMD heatsink has overheated
49 Prism has overheated (not applicable to Roadster S
4C Projector has shut down due to critical error
C0 Lamp cannot ignite due to blower failure
C6 TIPM is overheated
C7 TIPM is approaching the over-temperature threshold
53 Card cage fan failed (Fan 3) NOTE: may be connected as fan 4 or 5
54 LVPS fan failed fan failed (Fan 4) NOTE: may be connected as fan 3 or 5
55 Exhaust fan failed (Fan 5) NOTE: may be connected as fan 3 or 4
56 Prism fan failed (Fan 6)
57 Red DMD fan failed (Fan 7)
TIPM (10-bit Image Processor)
60 Boot code CRC failed
61 Unable to program DigMux PLD
62 Unable to program Control PLD
63 Unable to program Bubks PLD
64 Unrecognized ROM type
65 Write to flash ROM failed
66 General TIPM failure
67 Downloaded code will not fit into ROMs
68 Communication failure with scaler on TIPM
Keypad and EEPROM
70 Unable to access EEPROM on the built-in keypad
71 EEPROM memory on the built-in keypad has reinitialized
PANEL DRIVER or FORMATTERS
80 Unrecognized Panel Driver
81 Unable to program device on Panel Driver
82 TI flash download failure
83 TI flash download failure
84 TI flash download failure
2
85 TI - I C write failure
86 One or more Formatters is not responding — probable Formatter s/w fault
87 Formatter reports consecutive RDRAM failures
88 Red modular Formatter communication failure
89 Green modular Formatter communication failure
8A Blue modular Formatter communication failure
93 Modular Formatter architecture error
94 Modular Formatter / DMD mismatch
95 Modular Formatter sequence mismatch
MISCELLANEOUS
A0 Unable to program the optional interface module
A1 Unable to power the optional interface module
A2 Unable to program the Dual Slot Backplane Module (DSBP)
A3 Unable to program the warping module option (ChristieTWIST)
f you encounter a system error, clear it with
powering it off and on again (cooling if necessary). Contact dealer/factory if error persists.
The specific code number identifies the source of the error detected, and is
particularly useful in cases wher8e the projector is too far away to read the
accompanying text message in the LCD status display window. For example, the
code "21" means the lamp could not be turned on. Error codes for this projector are
listed in Table 3.4.
+
12K)
Exit Exit
. If necessary, try resetting the projector by
Roadster / Mirage S+ User's Manual
OPERATION
3-67