Machine Default - Kyocera KM-1650 Service Manual

2DA/2DB-1

(4) Machine default

Auto drawer switching ON/OFF
Turns automatic drawer switching ON or OFF.
1. Select [Auto Cassette SW] and then press the enter
key.
2. Select [On/All types of paper], [On/Only same
paper type] or [Off] and then press the enter key.
Paper size (drawer 1 to 4)
Sets the size of paper that is loaded in drawer 1
through 4.
1. Select one of the [Paper Size (1st) to (4th)] and
then press the enter key.
2. Select [Auto Detection Metric], [Auto Detection
Inch] or a paper size and then press the enter key.
* For 16 ppm model, the setting for drawer 2, 3 and
4 will only be available when the optional paper
feeder is installed.
* For 20 ppm model, the setting for drawer 3 and 4
will only be available when the optional paper
feeder is installed.
Paper type (drawer 1 to 4)
Sets the type of paper that is loaded in drawers 1
through 4.
1. Select one of the [Paper Type (1st) to (4th)] and
then press the enter key.
2. Select the paper type and then press the enter key.
* For 16 ppm model, the setting for drawer 2, 3 and
4 will only be available when the optional paper
feeder is installed.
* For 20 ppm model, the setting for drawer 3 and 4
will only be available when the optional paper
feeder is installed.
Bypass tray settings display ON/OFF
1. Select one of the [Check Bypass] and then press
the enter key.
2. Select [On] or [Off] and then press the enter key.
Paper weight for paper type
Sets the paper weight for each paper type.
1. Select [P. type (Weight)] and then press the enter
key.
2. Select paper type and then press the enter key.
3. Select paper weight and then press the enter key.
Duplex print for paper type
Sets whether or not each custom type of paper (cus-
tom 1 to custom 8) will be available for use in duplex
printing.
1. Select [P. type (Duplex)] and then press the enter
key.
2. Select one of the [Custom 1 to 8] and then press
the enter key.
3. Select [On] or [Off] and then press the enter key.
1-4-58
Custom paper type
Sets whether or not to match the orientation in one-
sided printing and two-sided printing.
1. Select [Special P. type] and then press the enter
key.
2. Select [Match Print Direction] or [Fast Mode] and
then press the enter key.
Original orientation
Sets the default original orientation.
1. Select [Orig. direction] and then press the enter
key.
2. Select [Rear] or [Left top] and then press the enter
key.
Auto sleep time
Sets the time that elapses before the auto sleep func-
tion.
1. Select [Sleep mode time] and then press the enter
key.
2. Sets sleep mode type and then press the enter key.
Setting range:
1 to 240 min (Inch specifications)
1 to 120 mim (metric specifications)
Auto low power time
Sets the time that elapses before the low power mode
is automatically activated.
1. Select [Low power time] and then press the enter
key.
2. Sets low power time and then press the enter key.
Setting range:
1 to 240 mm (Inch specifications)
1 to 120 mm (metric specifications)
Copy eject location
Sets the paper output location with priority for copying.
This setting is only available when the optional finisher
or job separator are installed in the machine.
1. Select [Copy Otput Destn] and then press the enter
key.
2. Select output location and then press the enter key.
Fax eject location
Sets where incoming faxes will be ejected. This setting
is only available when the optional fax kit, finisher or
job separator are installed in the machine.
1. Select [Fax Output Destn] and then press the enter
key.
2. Select output location and then press the enter key.