Roland VM-C7100 Owner's Manual page 174

Lo Mid Q (Low Middle Q)
Lo Gain (Low Gain)
Lo Freq (low frequency)
Lo Q (Low Q)
Lo Type (Low Type)
Output Level (Level)
BassCut (Bass Cut Filter): Cuts off undesired low frequency band sounds such as pop noise.
Sw (Switch)
Freq (Frequency)
Enhancer:
Sw (Switch)
Mix Level (Mix Level)
Sens (Sensitivity)
Freq (Frequency)
Input:
Gain (Input Gain)
Detect Time (Detect Time)
LoSplit Point (Low Split Point)
HiSplit Point (High Split Point)
Expander:
Sw (Switch)
Hi Thres (High Threshold)
Hi Ratio (High Ratio)
Hi Atck (High Attack)
Hi Rel (High Release)
Mid Thres (Middle Threshold)
Mid Ratio (Middle Ratio)
Mid Atck (Middle Attack)
Mid Rel (Middle Release)
Lo Thers (Low Threshold)
Lo Ratio (Low Raito)
Lo Atck (Low Attack)
Lo Rel (Low Release)
0.36–16
-15– +15 dB
20–2.00 kHz
0.36–16
Shelv, Peak
-30– +15 dB
On, Off
Thru, 20 - 2000 Hz
Accentuates the sound and push the sound forward.
On, Off Turns the enhancer on or off.
-24– +12dB Set the amount of the enhancer sound to be added to the direct sound.
0–100 Sets the degree of the enhancer effect desired.
1.0–10.0 kHz Sets the frequency at which the enhancer effect starts working.
Splits the direct sound into three frequency bands, that is, low, middle and high
frequency bands.
-24– +12dB Sets the overall volume before entering expander/compressor.
0–10 ms Sets the length of delay to add to the direct sound input.
20–800 Hz Sets the frequency at which the direct sound is split into three bands (on the
low frequency band side).
1.6–16 kHz Sets the frequency at which the direct sound is split into three bands (on the
high frequency band side).
Expands the dynamic range at a certain ratio.
On, Off Turns the expander on or off.
-80–0 dB Sets the volume at which the expander for the high frequency band starts
working .
1:1–16:1, INF:1 Sets the ratio at which the output in the high frequency band is increased
when the input level has dropped below the high threshold level.
0–100 ms Sets the time until when the high frequency band expander starts working
after the input level dropps below the high threshold level.
50–5000 ms Sets the time until when the high frequency band expander stops working
after the input level exceeds the high threshold level.
-80–0 dB Sets the volume at which the expander for the middle frequency band starts working.
1:1–16:1, INF:1 Sets the ratio at which the output in the middle frequency band is increased
when the input level has dropped below the middle threshold level.
0–100 ms Sets the time until when the middle frequency band expander starts working
after the input level dropps below the middle threshold level.
50–5000 ms Sets the time until when the middle frequency band expander stops working
after the input level exceeds the middle threshold level.
-80–0 dB Sets the volume at which the expander for the low frequency band starts working .
1:1–16:1, INF:1 Sets the ratio at which the output in the low frequency band is increased
when the input level has dropped below the low threshold level.
0–100 ms Sets the time until when the low frequency band expander starts working
after the input level dropps below the low threshold level.
50–5000 ms Sets the time until when the high frequency band expander stops working
after the input level exceeds the low threshold level.
Chapter 8 Using the Internal Effects
Sets the width of the area around the low middle frequency
that will be affected by the gain settings.
Sets the boost/cut amount in the low frequency band.
Sets the center frequency in the low frequency band.
Sets the width of the area around the low frequency that
will be affected by the gain settings.
Sets the type of the low frequency band equalizer
(shelving type or peaking type).
Sets the overall volume after passing through the equalizer.
Turns the bass cut filter on or off.
Sets the frequency for cutting off undesired low frequency
band sounds such as pop noise.
*1
Continued...
173