Roland VM-C7100 Owner's Manual page 154

Parameter (full name)
Reverb 2:
Sw (Switch)
Type (Reverb Type)
Time (Reverb Time)
Pre-Delay (Pre-Delay)
Density (Density)
Effect Level (Effect Level).
Direct Level (Direct Level)
LoPass Freq (Low Pass Filter)
HiPass Freq (High Pass Filter)
Gate (Gate)
Gate Thresh (Threshold)
Gate Attack (Attack)
Gate Release (Release)
Gate Hold Time (Hold Time)
Mode (Gate Mode)
3 BAND EQ (Equalizer)
Sw (Switch)
Hi Gain (High Gain)
Hi Freq (high frequency)
Hi Q (High Q)
Hi Type (High Type)
Mid Gain (Middle Gain)
Mid Freq (middle frequency)
Mid Q (Middle Q)
Lo Gain (Low Gain)
Lo Freq (low frequency)
Lo Q (Low Q)
Lo Type (Low Type)
Output Level (Output Level)
*1: If Low Type (Lo Type) or High Type (Hi Type) is set to "Shelv (Shelving Type)," the setting for Lo Q or High Q
is invalid.
Frequency (p. 237), Q (p. 243), Shelving Type (p. 244), Peaking Type (p. 242), Equalizer (p. 236), Reverb (p. 244),
HPF (p. 238), LPF (p. 239)
Setting
Gate reverb with two modes of gate operation
On, Off
See the column on
the previous page.
0.1–10.0 sec.
0–200 ms
0–100
0–100
0–100
1.0–20.0 kHz, Thru
Thru, 20 - 2000 Hz
On, Off
0–100
1–100
1–100
1–100
Gate, Duckn
On, Off
-12– +12 dB
1.4–20.0 kHz
0.3–10.0
Shelv, Peak
-12– +12 dB
200–8000 Hz
0.3–10.0
-12– +12dB
20 - 2000 Hz
0.3–10.0
Shelv, Peak
0–100
Chapter 8 Using the Internal Effects
Function
Turns the reverb on or off.
Sets the reverb type.
Sets the length (time) of the reverb sound.
Sets the time until the reverb sound is output.
Sets the density of the reverb sound.
Sets the volume of the reverb sound.
Sets the volume of the direct sound.
Sets the frequency at which LPF starts taking effect.
Set this to "Thru" if LPF is to be disabled.
Sets the frequency at which HPF starts taking effect.
Set this to "Thru" if HPF is to be disabled.
Opens or closes the gate.
Sets the reference volume for controlling gate operations.
Sets the time from when the direct sound level exceeds the
threshold level until when the gate is completely open.
Sets the time from when the hold time has elapsed until the
sound is completely muted.
Sets the time from when the input falls below the threshold
level until when the release begins.
Sets the gate operation type.
Turns the equalizer on or off.
Sets the boost/cut amount in the high frequency band.
Sets the center frequency in the high frequency band.
Sets the width of the area around the high frequency that
will be affected by the gain settings.
Sets the type of the high frequency band equalizer
(shelving type or peaking type).
Sets the boost/cut amount in the middle frequency band.
Sets the center frequency in the middle frequency band.
Sets the width of the area around the middle frequency that
will be affected by the gain settings.
Sets the boost/cut amount in the low frequency band.
Sets the center frequency in the low frequency band.
Sets the width of the area around the low frequency that
will be affected by the gain settings.
Sets the type of the low frequency band equalizer
(shelving type or peaking type).
Sets the volume after passing through the equalizer.
*1
*1
153